Owner manual

ManualsBrandsIEI Integration ManualsComputersPPC-5xxx-9455 v1.00

161

162

163

164

165

166

167

168

169

170

Table Of Contents

Revision
Copyright
Manual Conventions
Packing List
Table of Contents
List of Figures
List of Tables
BIOS Menus
1 Introduction
- 1.1 General Overview
- 1.2 External Overview
- 1.3 Internal Overview
2 Specifications
- 2.1 Introduction
- 2.2 Dimensions
- 2.3 Motherboard
- 2.4 CPU Support
- 2.5 System Chipsets
  - 2.5.1 Intel® 945G Northbridge Chipset
  - 2.5.2 ICH7 Southbridge Chipset
- 2.6 Graphics Support
  - Analog CRT Support
  - 2.6.2 LVDS Support
- 2.7 Memory
- 2.8 Storage
  - CompactFlash®
  - 2.8.2 SATA Hard Drive
- 2.9 Expansion Slots
- 2.10 External Device Connectors
- 2.11 Gigabit Ethernet
- 2.12 Front Panel
  - 2.12.1 Flat Screen
  - 2.12.2 Touch Screen
- 2.13 OEM Options
3 Unpacking
- 3.1 Anti-static Precautions
- 3.2 Unpacking Precautions
- 3.3 Package Contents
4 Installation and Configuration
- 4.1 Installation Precautions
- 4.2 Preinstalled Components
- 4.3 Installation and Configuration Steps
- 4.4 Remove the Back Cover
- 4.5 Jumper Settings
- 4.6 Drive Installation
- 4.7 Mounting the System
- 4.8 External Peripheral Interface Connectors
5 BIOS Setup
- 5.1 Introduction
- 5.2 Main
- 5.3 Advanced
- 5.4 PCI/PnP
- 5.5 Boot
- 5.6 Security
- 5.7 Chipset
  - 5.7.1 Northbridge Configuration
  - 5.7.2 Southbridge Configuration
- 5.8 Exit
6 Software Installation
- 6.1 Available Software Drivers
- 6.2 Chipset Driver
- 6.3 Graphics Driver
- 6.4 Gigabit Ethernet Driver Installation
- 6.5 Audio Driver
  - 6.5.1 BIOS Setup
  - 6.5.2 Driver Installation
- 6.6 Touch Panel Driver
7 System Maintenance
- 7.1 System Maintenance Introduction
- 7.2 Motherboard Replacement
- 7.3 Back Cover Removal
- 7.4 DIMM Replacement
- 7.5 Elevated Platform Removal
- 7.6 PSU Module Replacement
  - 7.6.1 Remove the Old PSU
  - 7.6.2 Install the New PSU
- 7.7 System Cooling Fan Replacement
  - 7.7.1 Remove the Old System Cooling Fans
  - 7.7.2 Install the New System Cooling Fans
A BIOS Options
B Terminology
C Digital I/O Interface
- C.1 Introduction
- C.2 DIO Connector Pinouts
- C.3 Assembly Language Samples
  - C.3.1 Enable the DIO Input Function
  - C.3.2 Enable the DIO Output Function
D Watchdog Timer
E Address Mapping
- E.1 Direct Memory Access (DMA)
- E.2 Input/Output (IO)
- E.3 Interrupt Request (IRQ)
- E.4 Memory
F Compatibility
- F.1 Compatible Operating Systems
- F.2 Compatible Processors
- F.3 Compatible Memory Modules
G Hazardous Materials Disclosure
- G.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury
Index

PPC-5xxx-9455 Panel PC

Page 148

Step 5: Remove the retention screws that connect the PSU bracket to the chassis

(

Figure 7-8).

Figure 7-8: PSU Rear Panel Screws

Step 6: Remove the retention screws that connect the PSU to the PSU bracket.Step 0:

7.6.2 Install the New PSU

Installation is done in the reverse order to removal. To install a new PSU module, please

follow the steps below.

Step 1: Attach the PSU bracket to the PSU module with the previously removed

retention screws.

Step 2: Insert the PSU module and bracket assembly into the chassis and attach the

PSU bracket to the chassis with the previously removed retention screws.

Step 3: Secure the PSU module to the chassis by reinserting the previously removed

retention screws through the bottom panel.

Step 4: Bundle the cables of the new PSU module and secure them with a plastic tie

similar to the old PSU module.

Step 5: Reconnect all previously disconnected power connectors to the motherboard

and disk drives.

Step 6: Reattach the elevated platform.

Step 7: Replace the back cover.Step 0: