KINO-GM45A Mini-ITX SBC KINO-GM45A CPU Card IEI Technology Corp. MODEL: KINO-GM45A Mini-ITX Motherboard Supports Intel® Core™2 Duo CPU, VGA/LVDS/HDTV-out, GbE, USB 2.0 and Two SATA II User Manual Page I Rev. 1.
KINO-GM45A Mini-ITX SBC Revision Date Version Changes 11 January, 2010 1.
KINO-GM45A Mini-ITX SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
KINO-GM45A Mini-ITX SBC Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 INTRODUCTION........................................................................................................... 2 1.2 CONNECTORS ............................................................................................................. 3 1.3 DIMENSIONS ..............................................................................
KINO-GM45A Mini-ITX SBC 3.2.11 12V Power Connector .................................................................................... 29 3.2.12 SATA Drive Connectors ................................................................................. 30 3.2.13 SATA Power Connector.................................................................................. 31 3.2.14 Serial Port Connector (RS-232/422/485) ...................................................... 31 3.2.15 Serial Port Connectors (RS-232) ...
KINO-GM45A Mini-ITX SBC 4.7.1 Audio Kit Installation....................................................................................... 57 4.7.2 Keyboard/Mouse Connector ............................................................................ 58 4.7.3 Dual RS-232 Cable with Slot Bracket.............................................................. 60 4.8 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 61 4.8.1 LAN Connection (Single Connector) ...........
KINO-GM45A Mini-ITX SBC 5.7.2 Southbridge Configuration ............................................................................ 100 5.8 EXIT ....................................................................................................................... 101 A BIOS MENU OPTIONS ........................................................................................... 103 B TERMINOLOGY......................................................................................................
KINO-GM45A Mini-ITX SBC List of Figures Figure 1-1: KINO-GM45A................................................................................................................2 Figure 1-2: Connectors ..................................................................................................................3 Figure 1-3: KINO-GM45A Dimensions (mm) ................................................................................4 Figure 1-4: External Interface Panel Dimensions (mm) ......................
KINO-GM45A Mini-ITX SBC Figure 4-5: Jumper Locations .....................................................................................................50 Figure 4-6: AT Power Select Jumper Location..........................................................................52 Figure 4-7: Clear CMOS Jumper .................................................................................................53 Figure 4-8: COM 2 Function Select Jumper Location........................................................
KINO-GM45A Mini-ITX SBC List of Tables Table 1-1: Technical Specifications..............................................................................................8 Table 3-1: Peripheral Interface Connectors ...............................................................................17 Table 3-2: Rear Panel Connectors ..............................................................................................17 Table 3-3: Audio Connector Pinouts ...................................................
KINO-GM45A Mini-ITX SBC Table 4-5: LVDS Panel Resolution Jumper Settings.................................................................55 Table 4-6: LVDS Voltage Selection Jumper Settings................................................................56 Table 5-1: BIOS Navigation Keys ................................................................................................
KINO-GM45A Mini-ITX SBC List of BIOS Menus BIOS Menu 1: Main .......................................................................................................................70 BIOS Menu 2: Advanced ..............................................................................................................72 BIOS Menu 3: CPU Configuration ...............................................................................................72 BIOS Menu 4: IDE Configuration..................................
KINO-GM45A Mini-ITX SBC Chapter 1 1 Introduction Page 1
KINO-GM45A Mini-ITX SBC 1.1 Introduction Figure 1-1: KINO-GM45A The KINO-GM45A Mini-ITX motherboard is a Socket P 45nm Intel® Core™2 Duo processor (Penryn) platform. Up to two 2.0 GB 667 MHz or 800 MHz DDR2 SDRAM SO-DIMM are supported by the Intel® GM45 graphics memory controller hub (GMCH). The Intel® GM45 GMCH also supports 18-bit or 24-bit dual-channel LVDS, analog CRT, HDMI and HDTV output.
KINO-GM45A Mini-ITX SBC 1.2 Connectors The connectors on the KINO-GM45A are shown in the figure below.
KINO-GM45A Mini-ITX SBC 1.3 Dimensions 1.3.
KINO-GM45A Mini-ITX SBC 1.3.2 External Interface Panel Dimensions External peripheral interface connector panel dimensions are shown in Figure 1-4.
KINO-GM45A Mini-ITX SBC 1.4 Data Flow Figure 1-5 shows the data flow between the two on-board chipsets and other components 4 installed on the motherboard and described in the following sections of this chapter.
KINO-GM45A Mini-ITX SBC 1.5 Technical Specifications KINO-GM45A technical specifications are listed in table below. Specification KINO-GM45A Form Factor Mini-ITX Socket Socket P CPU Supported 45 nm Socket P Intel® Core™2 Duo processor Front Side Bus (FSB) 1066 MHz (Max.), 800 MHz or 667 MHz Northbridge Chipset Intel® GM45 Southbridge Chipset Intel® ICH9M Memory Two 200-pin SO-DIMM sockets support two 667/800 MHz 2.0 GB (max.) DDR2 SDRAM SO-DIMM (system max. 4 GB) Audio Realtek ALC888 HD 7.
KINO-GM45A Mini-ITX SBC Specification KINO-GM45A Display Ports One VGA port One 18-bit or 24-bit dual-channel LVDS port One TV-out port supports HDTV One external HDMI port supports up to 1080p Ethernet One RJ-45 GbE port Serial Ports Three RS-232 via three 10-pin header connectors One RS-232/422/485 via 14-pin header connector USB 2.0/1.1 Ports Eight external USB ports Storage Serial ATA Two independent serial ATA (SATA) channels with 3.
KINO-GM45A Mini-ITX SBC Chapter 2 2 Unpacking Page 9
KINO-GM45A Mini-ITX SBC 2.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Make sure to adhere to the following guidelines: Wear an anti-static wristband: Wearing an anti-static wristband can prevent electrostatic discharge. Self-grounding: Touch a grounded conductor every few minutes to discharge any excess static buildup.
KINO-GM45A Mini-ITX SBC 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the KINO-GM45A was purchased from or contact an IEI sales representative directly by sending an email to sales@iei.com.tw.
KINO-GM45A Mini-ITX SBC 1 Utility CD 1 Quick Installation Guide 2.3.
KINO-GM45A Mini-ITX SBC PCIe Mini wireless LAN card 802.11b/g (P/N: WMUSB-V01-RS) PCIe Mini wireless LAN card 802.
KINO-GM45A Mini-ITX SBC Chapter 3 3 Connectors Page 14
KINO-GM45A Mini-ITX SBC 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 KINO-GM45A Layout The figures below show all the connectors and jumpers.
KINO-GM45A Mini-ITX SBC 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board.
KINO-GM45A Mini-ITX SBC Serial ATA (SATA) drive connector 7-pin SATA S_ATA2 SATA power connector 4-pin wafer CN6 SATA power connector 4-pin wafer CN7 SPDIF connector 5-pin header SPDIF1 SPI Flash connector 8-pin header JSPI1 USB connector (1) 8-pin header USB23 USB connector (2) 8-pin header USB45 USB connector (3) 8-pin header USB67 Table 3-1: Peripheral Interface Connectors 3.1.3 External Interface Panel Connectors The table below lists the connectors on the external I/O panel.
KINO-GM45A Mini-ITX SBC 3.2 Internal Peripheral Connectors The section describes all of the connectors on the KINO-GM45A. 3.2.1 Audio Connector CN Label: AUDIO1 CN Type: 10-pin box header (2x5) CN Location: See Figure 3-2 CN Pinouts: See Table 3-3 The audio connector is connected to external audio devices including speakers and microphones for the input and output of audio signals to and from the system. Figure 3-2: Audio Connector Location PIN NO. DESCRIPTION PIN NO.
KINO-GM45A Mini-ITX SBC 3.2.2 Backlight Inverter Connector CN Label: INVERTER1 CN Type: 5-pin wafer (1x5) CN Location: See Figure 3-3 CN Pinouts: See Table 3-4 The backlight inverter connector provides the backlight on the LCD display connected to the KINO-GM45A with +12V of power. Figure 3-3: Panel Backlight Connector Pinout Locations PIN NO. DESCRIPTION 1 LCD Backlight Control 2 GROUND 3 +12V 4 GROUND 5 Backlight Enable Table 3-4: Panel Backlight Connector Pinouts 3.2.
KINO-GM45A Mini-ITX SBC The digital I/O connector provides programmable input and output for external devices. The digital I/O provides 4-bit output and 4-bit input. Figure 3-4: Digital I/O Connector Locations Pin Description Pin Description 1 GND 2 VCC 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input 3 8 Input 2 9 Input 1 10 Input 0 Table 3-5: Digital I/O Connector Pinouts 3.2.
KINO-GM45A Mini-ITX SBC Figure 3-5: CPU Fan Connector Location Pin Description 1 GROUND 2 +12V 3 CPUFANIN 4 CPUFANOUT Table 3-6: CPU Fan Connector Pinouts 3.2.5 Fan Connector (System) CN Label: FAN1 CN Type: 3-pin wafer (1x3) CN Location: See Figure 3-6 CN Pinouts: See Table 3-7 4 4 The cooling fan connector provides a 12V, 500mA current to the cooling fan.
KINO-GM45A Mini-ITX SBC Figure 3-6: +12V Fan Connector Locations PIN NO. DESCRIPTION 1 SYSFANIN0 2 +12V 3 GND Table 3-7: +12V Fan Connector Pinouts 3.2.6 Front Panel Connector CN Label: F_PANEL1 CN Type: 8-pin header (2x4) CN Location: See Figure 3-7 CN Pinouts: See Table 3-8 The front panel connector connects to external switches and indicators to monitor and controls the motherboard.
KINO-GM45A Mini-ITX SBC Figure 3-7: Front Panel Connector Location FUNCTION PIN DESCRIPTION FUNCTION PIN DESCRIPTION Power Button 1 PWRBTSW- Power LED 2 +V5S 3 GROUND 4 GROUND 5 +V5S 6 SYSRST- 7 -HDLED 8 GROUND HDD LED Reset Table 3-8: Front Panel Connector Pinouts 3.2.
KINO-GM45A Mini-ITX SBC Figure 3-8: Keyboard/Mouse Connector Location Pin Description 1 +5 VCC 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 GROUND Table 3-9: Keyboard/Mouse Connector Pinouts 3.2.8 LVDS LCD Connector CN Label: LVDS1 CN Type: 30-pin crimp (2x15) CN Location: See Figure 3-9 CN Pinouts: See Table 3-10 4 4 The 30-pin LVDS LCD connectors can be connected to single channel or dual channel, 18-bit LVDS panel.
KINO-GM45A Mini-ITX SBC Figure 3-9: LVDS LCD Connector Pinout Location PIN NO. DESCRIPTION PIN NO.
KINO-GM45A Mini-ITX SBC 3.2.9 PCIe Mini Card Slot CN Label: CN5 CN Type: 52-pin PCIe Mini Card Slot CN Location: See Figure 3-10 CN Pinouts: See Table 3-11 4 The PCIe mini card slot enables a PCIe mini card expansion module to be connected to the board. Cards supported include among others wireless LAN (WLAN) cards. Figure 3-10: PCIe Mini Card Slot Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 PCIE_WAKE# 2 3.3V 3 N/C 4 GND 5 N/C 6 1.
KINO-GM45A Mini-ITX SBC 19 N/C 20 N/C 21 GND 22 PCIRST# 23 PERN2 24 3VDual 25 PERP2 26 GND 27 GND 28 1.5V 29 GND 30 SMBCLK 31 PETN2 32 SMBDATA 33 PETP2 34 GND 35 GND 36 USBD- 37 N/C 38 USBD+ 39 N/C 40 GND 41 N/C 42 N/C 43 N/C 44 N/C 45 N/C 46 N/C 47 N/C 48 1.5V 49 N/C 50 GND 51 N/C 52 3.3V Table 3-11: PCIe Mini Card Slot Pinouts 3.2.
KINO-GM45A Mini-ITX SBC Figure 3-11: PCIe Mini Card Expansion Connector Location Pin Description Pin Description 1 NC 2 -- 3 PCIE_TXP1 4 PCIE_TXP2 5 PCIE_TXN1 6 PCIE_TXN2 7 GND 8 GND 9 PCIE_RXP1 10 PCIE_RXP2 11 PCIE_RXN1 12 PCIE_RXN2 13 GND 14 GND 15 CLK_PCIE_MINI_1 16 CLK_PCIE_MINI_2 17 CLK_PCIE_MINI_1# 18 CLK_PCIE_MINI_2# 19 GND 20 GND 21 USB_PP8 22 USB_PP9 23 USB_PN8 24 USB_PN9 25 GND 26 GND 27 MINICARD_CLKREQ1# 28 MINICARD_CLKREQ2# 29 PM_GPI
KINO-GM45A Mini-ITX SBC Pin Description Pin Description 41 PCIRST3- 42 PCIE_WAKE# 43 +V1.5S 44 +V3.3S 45 +V1.5S 46 +V3.3S 47 +V1.5S 48 +V3.3S Table 3-12: PCIe Mini Card Expansion Connector Pinouts 3.2.11 12V Power Connector CN Label: PWR2 CN Type: 4-pin Molex power connector (1x4) CN Location: See Figure 3-12 CN Pinouts: See Table 3-13 The connector supports the 12V power supply. Figure 3-12: CPU 12V Power Connector Location PIN NO. DESCRIPTION PIN NO.
KINO-GM45A Mini-ITX SBC 3.2.12 SATA Drive Connectors CN Label: S_ATA1 and S_ATA2 CN Type: 7-pin SATA drive connectors CN Location: See Figure 3-13 CN Pinouts: See Table 3-14 4 4 The two SATA II drive connectors are each connected to a SATA II drive. The SATA II drives transfer data at speeds as high as 3.0 Gb/s. Figure 3-13: SATA Drive Connector Locations PIN NO.
KINO-GM45A Mini-ITX SBC 3.2.13 SATA Power Connector CN Label: CN6 and CN7 CN Type: 4-pin wafer (1x4) CN Location: See Figure 3-14 CN Pinouts: See Table 3-15 The SATA Power Connector provides +5V and +12V power output to the SATA connector. Figure 3-14: SATA Power Connector Locations PIN NO. DESCRIPTION 1 +5V 2 GND 3 GND 4 +12V Table 3-15: SATA Power Connector Pinouts 3.2.
KINO-GM45A Mini-ITX SBC Used for RS-232/422/485 communications. Figure 3-15: Serial Port Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 GND 10 N/C 11 TXD485+ 12 TXD485# 13 RXD485+ 14 RXD485# Table 3-16: Serial Port Connector Pinouts 3.2.
KINO-GM45A Mini-ITX SBC Figure 3-16: COM Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 Data Carrier Direct (DCD) 2 Data Set Ready (DSR) 3 Receive Data (RXD) 4 Request To Send (RTS) 5 Transmit Data (TXD) 6 Clear To Send (CTS) 7 Data Terminal Ready (DTR) 8 Ring Indicator (RI) 9 Ground (GND) 10 N/C Table 3-17: COM Connector Pinouts 3.2.
KINO-GM45A Mini-ITX SBC Figure 3-17: SPDIF Connector Location PIN DESCRIPTION 1 5V 2 NC 3 SPDIF OUT 4 GND 5 SPDIF IN Table 3-18: SPDIF Connector Pinouts 3.2.17 SPI Flash Connector CN Label: JSPI1 CN Type: 8-pin header (2x4) CN Location: See Figure 3-18 CN Pinouts: See Table 3-19 The 6-pin SPI Flash connector is used to flash the BIOS.
KINO-GM45A Mini-ITX SBC Figure 3-18: SPI Flash Connector PIN DESCRIPTION PIN DESCRIPTION 1 SPI_VCC 2 GND 3 SPI_CS 4 SPI_CLK 5 SPI_SO 6 SPI_SI 7 NC 8 NC Table 3-19: SPI Flash Connector 3.2.18 USB Connectors CN Label: USB23, USB45 and USB67 CN Type: 8-pin header (2x4) CN Location: See Figure 3-19 CN Pinouts: See Table 3-25 The USB connectors connect to USB devices. Each pin header provides two USB ports.
KINO-GM45A Mini-ITX SBC Figure 3-19: USB Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC 2 GND 3 DATA- 4 DATA+ 5 DATA+ 6 DATA- 7 GND 8 VCC Table 3-20: USB Port Connector Pinouts 3.3 External Peripheral Interface Connector Panel Figure 3-20 shows the KINO-GM45A external peripheral interface connector (EPIC) panel.
KINO-GM45A Mini-ITX SBC Figure 3-20: KINO-GM45A External Peripheral Interface Connector 3.3.1 Audio Connector CN Label: SPEAKOUT1 CN Type: Audio jack CN Location: See Figure 3-20 The audio line-out jack connects to a headphone or a speaker. With multi-channel configurations, this port can also connect to front speakers. 3.3.
KINO-GM45A Mini-ITX SBC Figure 3-21: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the port is linked. See Table 3-22. 5 STATUS DESCRIPTION STATUS DESCRIPTION GREEN Activity YELLOW Linked Table 3-22: RJ-45 Ethernet Connector LEDs 3.3.
KINO-GM45A Mini-ITX SBC 7 HDMI_DATA0 19 HDMI_HPD 8 GND 20 HDMI_GND 9 HDMI_DATA0# 21 HDMI_GND 10 HDMI_CLK 22 HDMI_GND 11 GND 23 HDMI_GND 12 HDMI_CLK# Table 3-23: HDMI Connector Pinouts 3.3.4 TV Connector CN Label: TV1 CN Type: 7-pin Mini-DIN CN Location: See Figure 3-20 CN Pinouts: See Table 3-24 A 7-pin mini DIN connector is located on the mounting bracket for easy connection to a TV OUT cable. PIN NO.
KINO-GM45A Mini-ITX SBC CN Location: See Figure 3-20 CN Pinouts: See Table 3-25 5 5 The KINO-GM45A has two external USB 2.0 ports. The ports connect to both USB 2.0 and USB 1.1 devices. PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC 5 VCC 2 DATA- 6 DATA- 3 DATA+ 7 DATA+ 4 GROUND 8 GROUND Table 3-25: USB Port Connector Pinouts (USB1_2) 3.3.
KINO-GM45A Mini-ITX SBC PIN DESCRIPTION PIN DESCRIPTION 1 RED 9 VGAVCC 2 GREEN 10 GROUND 3 BLUE 11 NC 4 NC 12 DDCDAT 5 GROUND 13 HSYNC 6 CRT_PLUG# 14 VSYNC 7 GROUND 15 DDCCLK 8 GROUND Table 3-26: VGA Connector Pinouts Page 41
KINO-GM45A Mini-ITX SBC Chapter 4 4 Installation Page 42
KINO-GM45A Mini-ITX SBC 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the KINO-GM45A may result in permanent damage to the KINO-GM45A and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO-GM45A. Dry climates are especially susceptible to ESD.
KINO-GM45A Mini-ITX SBC 4.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the KINO-GM45A is installed. All installation notices pertaining to the installation of the KINO-GM45A should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the KINO-GM45A and injury to the person installing the motherboard. 4.2.
KINO-GM45A Mini-ITX SBC o When working with the KINO-GM45A, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system. Before and during the installation of the KINO-GM45A DO NOT: Remove any of the stickers on the PCB board. These stickers are required for warranty validation. Use the product before verifying all the cables and power connectors are properly connected.
KINO-GM45A Mini-ITX SBC 4.4.1 Socket P CPU Installation WARNING: CPUs are expensive and sensitive components. When installing the CPU please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed. To install a socket P CPU onto the KINO-GM45A, follow the steps below: WARNING: When handling the CPU, only hold it on the sides. DO NOT touch the pins at the bottom of the CPU. Step 1: Unlock the CPU retention screw.
KINO-GM45A Mini-ITX SBC Figure 4-1: Make sure the CPU socket retention screw is unlocked Step 2: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air. Step 3: Correctly Orientate the CPU. Make sure the IHS (integrated heat sink) side is facing upwards. Step 4: Correctly position the CPU. Match the Pin 1 mark with the cut edge on the CPU socket. See Figure 4-1.
KINO-GM45A Mini-ITX SBC Figure 4-2: Lock the CPU Socket Retention Screw 4.4.2 Socket P Cooling Kit Installation An IEI Socket P CPU cooling kit can be purchased separately. (See Chapter 3) The cooling kit comprises a CPU heat sink and a cooling fan. WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the heat sink. The thermal paste between the CPU and the heat sink is important for optimum heat dissipation.
KINO-GM45A Mini-ITX SBC Figure 4-3: Cooling Kit Support Bracket Step 2: Open the lever at the top of the heat sink. Lift the lever at the top of the cooling kit to loosen the cooling kit clamps. Step 3: Secure the cooling kit. Gently place the heat sink and cooling kit onto the CPU. Make sure the hooks are properly secured to the bracket. To secure the cooling kit, close the top lever. Step 4: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the KINO-GM45A.
KINO-GM45A Mini-ITX SBC 4.4.3 SO-DIMM Installation To install an SO-DIMM, please follow the steps below and refer to Figure 4-4. Figure 4-4: SO-DIMM Installation Step 1: Locate the SO-DIMM socket. Place the board on an anti-static mat. Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the notch on the memory socket. Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See Figure 4-4) Step 4: Seat the SO-DIMM. Gently push downwards and the arms clip into place.
KINO-GM45A Mini-ITX SBC Before the KINO-GM45A is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the KINO-GM45A are listed in Table 4-1. 5 Description Type Label AT Power Mode Setting 2-pin wafer ATXCTL1 Clear CMOS 3-pin header J_CMOS1 COM2 Function Select 8-pin header JP5 LVDS Panel Resolution 8-pin header JP1 LVDS Voltage Select 3-pin header J_VLVDS1 Table 4-1: Jumpers 4.5.
KINO-GM45A Mini-ITX SBC Figure 4-6: AT Power Select Jumper Location 4.5.2 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 3-pin header (1x3) Jumper Settings: See Table 4-3 Jumper Location: See Figure 4-7 5 5 If the KINO-GM45A fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
KINO-GM45A Mini-ITX SBC Clear CMOS Description Short 1 - 2 Keep CMOS Setup Short 2 - 3 Clear CMOS Setup Default Table 4-3: Clear CMOS Jumper Settings The location of the clear CMOS jumper is shown in Figure 4-7 below. 5 Figure 4-7: Clear CMOS Jumper 4.5.
KINO-GM45A Mini-ITX SBC Setting Description Short 1-2 RS-232 Short 3-4 RS-422 Short 5-6 RS-485 Short 5-6, 7-8 RS-485 with RTS control Table 4-4: COM 2 Function Select Jumper Settings Figure 4-8: COM 2 Function Select Jumper Location 4.5.
KINO-GM45A Mini-ITX SBC JP1 Description Open LVDS1 640 x 480 (18-bit) Short 1-2 LVDS1 800 x 600 (18-bit) Short 3-4 LVDS1 1024 x 768 (18-bit) Short 1-2, 3-4 LVDS1 1024 x 768 (24-bit) Short 5-6 Reserve Short 1-2, 5-6 LVDS1 1280 x 1024 (48-bit) Short 3-4, 5-6 LVDS1 1600 x 1200 (48-bit) Short 1-2, 3-4, 5-6 Reserve Default Table 4-5: LVDS Panel Resolution Jumper Settings The LVDS Panel Resolution jumper location is shown in Figure 4-9.
KINO-GM45A Mini-ITX SBC 4.5.5 LVDS Voltage Selection WARNING: Permanent damage to the screen and KINO-GM45A may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that cam with the monitor to select the correct voltage. Jumper Label: J_VLVDS1 Jumper Type: 3-pin header (1x3) Jumper Settings: See Table 4-6 Jumper Location: See Figure 4-10 The LVDS Voltage Selection jumpers allow the LVDS screen voltages to be set. The jumper sets the voltage connected to LVDS1.
KINO-GM45A Mini-ITX SBC 4.6 Chassis Installation 4.6.1 Airflow WARNING: Airflow is critical to the cooling of the CPU and other onboard components. The chassis in which the KINO-GM45A must have air vents to allow cool air to move into the system and hot air to move out. The KINO-GM45A must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface.
KINO-GM45A Mini-ITX SBC Step 2: Align pin 1. Align pin 1 on the on-board connector with pin 1 on the audio kit connector. Pin 1 on the audio kit connector is indicated with a white dot. See Figure 4-11. Figure 4-11: Audio Kit Cable Connection Step 3: Connect the audio devices. Connect speakers to the line-out audio jack. Connect the output of an audio device to the line-in audio jack. Connect a microphone to the mic-in audio jack.Step 0: 4.7.
KINO-GM45A Mini-ITX SBC Step 2: Align the connectors. Correctly align pin 1 on the cable connector with pin 1 on the KINO-GM45A keyboard/mouse connector. See Figure 4-12. Step 3: Insert the cable connectors. Once the cable connector is properly aligned with the keyboard/mouse connector on the KINO-GM45A, connect the cable connector to the on-board connectors. See Figure 4-12. Figure 4-12: Keyboard/mouse Y-cable Connection Step 4: Attach PS/2 connectors to the chassis.
KINO-GM45A Mini-ITX SBC both marked. Please make sure the keyboard and mouse are connected to the correct PS/2 connector. Step 0: 4.7.3 Dual RS-232 Cable with Slot Bracket The dual RS-232 cable slot connector consists of two connectors attached to two independent cables. Each cable is then attached to a D-sub 9 male connector that is mounted onto a slot. To install the dual RS-232 cable, please follow the steps below. Step 1: Locate the connectors.
KINO-GM45A Mini-ITX SBC 4.8 External Peripheral Interface Connection The following external peripheral devices can be connected to the external peripheral interface connectors. RJ-45 Ethernet cable connectors USB devices VGA monitors To install these devices, connect the corresponding cable connector from the actual device to the corresponding KINO-GM45A external peripheral interface connector making sure the pins are properly aligned. 4.8.
KINO-GM45A Mini-ITX SBC Figure 4-14: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the onboard RJ-45 connector. Step 0: 4.8.2 USB Connection (Dual Connector) The external USB Series "A" receptacle connectors provide easier and quicker access to external USB devices. Follow the steps below to connect USB devices to the KINO-GM45A. Step 1: Locate the USB Series "A" receptacle connectors.
KINO-GM45A Mini-ITX SBC Figure 4-15: USB Connector 4.8.3 VGA Monitor Connection The KINO-GM45A has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the KINO-GM45A, please follow the instructions below. Step 1: Locate the female DB-15 connector. The location of the female DB-15 connector is shown in Chapter 3. Step 2: Align the VGA connector.
KINO-GM45A Mini-ITX SBC Figure 4-16: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector. Step 0: 4.9 Software Installation All the drivers for the KINO-GM45A are on the CD that came with the system. To install the drivers, please follow the steps below. Step 1: Insert the CD into a CD drive connected to the system.
KINO-GM45A Mini-ITX SBC Figure 4-17: Introduction Screen Step 3: Click KINO-GM45A. Step 4: A new screen with a list of available drivers appears (Figure 4-18).
KINO-GM45A Mini-ITX SBC Figure 4-18: Available Drivers Step 5: Install all of the necessary drivers in this menu.
KINO-GM45A Mini-ITX SBC Chapter 5 5 BIOS Screens Page 67
KINO-GM45A Mini-ITX SBC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2. Press the DELETE key when the “Press Del to enter SETUP” message appears on the screen. 0.
KINO-GM45A Mini-ITX SBC Key Function F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 5.1.
KINO-GM45A Mini-ITX SBC 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset System Overview ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ AMIBIOS Version :08.00.15 Build Date :11/16/09 ID: :B146MZ11 Processor Type Speed Count Exit Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time.
KINO-GM45A Mini-ITX SBC The System Overview field also has two user configurable fields: Î System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. Î System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. 5.
KINO-GM45A Mini-ITX SBC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Advanced Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction > > > > > > > > Exit Configure CPU CPU Configuration IDE Configuration SuperIO Configuration Hardware Health Configuration AHCI Configuration Remote Access Configuration USB Configuration Power Configuration> ÅÆ Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Sa
KINO-GM45A Mini-ITX SBC Brand String: Lists the brand name of the CPU being used Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed Cache L1: Lists the CPU L1 cache size Cache L2: Lists the CPU L2 cache size 5.3.2 IDE Configuration Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration of the IDE devices installed in the system.
KINO-GM45A Mini-ITX SBC Î Compatible DEFAULT Configures the on-board ATA/IDE controller to be in compatible mode. In this mode, a SATA channel will replace one of the IDE channels. This mode supports up to 4 storage devices. Î Configures the on-board ATA/IDE controller to be in Enhanced Enhanced mode. In this mode, IDE channels and SATA channels are separated. This mode supports up to 6 storage devices. Some legacy OS do not support this mode.
KINO-GM45A Mini-ITX SBC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Primary IDE Master ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Device :Not Detected Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Enabled] Power Exit Select the type of device connected to the system ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.
KINO-GM45A Mini-ITX SBC Î 32Bit Data Transfer: Enables 32-bit data transfer. Type [Auto] Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from after the Power-On Self-Test (POST) is complete. Î BIOS is prevented from searching for an IDE disk Not Installed drive on the specified channel. Î Auto DEFAULT The BIOS auto detects the IDE disk drive type attached to the specified channel.
KINO-GM45A Mini-ITX SBC Î Block (Multi Sector Transfer) [Auto] Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the device supports multi-sector transfers. Î BIOS is prevented from using Multi-Sector Transfer on the Disabled specified channel. The data to and from the device occurs one sector at a time. Î Auto DEFAULT BIOS auto detects Multi-Sector Transfer support on the drive on the specified channel.
KINO-GM45A Mini-ITX SBC Î Auto DEFAULT BIOS auto detects the DMA mode. Use this value if the IDE disk drive support cannot be determined. Î SWDMA0 Single Word DMA mode 0 selected with a maximum data transfer rate of 2.1 MB/s Î SWDMA1 Single Word DMA mode 1 selected with a maximum data transfer rate of 4.2 MB/s Î SWDMA2 Single Word DMA mode 2 selected with a maximum data transfer rate of 8.3 MB/s Î MWDMA0 Multi Word DMA mode 0 selected with a maximum data transfer rate of 4.
KINO-GM45A Mini-ITX SBC Î S.M.A.R.T [Auto] Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts impending drive failures. The S.M.A.R.T BIOS option enables or disables this function. Î Î Auto Î Disabled Prevents BIOS from using the HDD SMART feature. Î Enabled Allows BIOS to use the HDD SMART feature BIOS auto detects HDD SMART support.
KINO-GM45A Mini-ITX SBC Î Serial Port1 Address [3F8/IRQ4] Use the Serial Port1 Address option to select the Serial Port 1 base address.
KINO-GM45A Mini-ITX SBC Î 10 Î DEFAULT Serial port 3 IRQ address is 10 Serial Port4 Address [2E8] Use the Serial Port4 IRQ option to select the interrupt address for serial port 4. Î Disabled No base address is assigned to serial port 3 Î 3E8 Serial port 4 I/O port address is 3E8 Î 2E8 Î DEFAULT Serial port 4 I/O port address is 2E8 Serial Port4 IRQ [10] Use the Serial Port4 IRQ option to select the interrupt address for serial port 4.
KINO-GM45A Mini-ITX SBC 5.3.4 Hardware Health Configuration The Hardware Health Configuration menu (BIOS Menu 7) shows the operating temperature, fan speeds and system voltages. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Hardware Health Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ CPU_FAN1 Mode Setting [Full On Mode] CPU Temperature System Temperature PWM Temperature :52ºC/127ºF :36ºC/96ºF :21ºC/69ºF CPU_Fan Speed FAN1 Speed :5976 RPM :N/A CPU Core +1.05V +3.30V +5.
KINO-GM45A Mini-ITX SBC Use the AHCI Settings menu (BIOS Menu 8) to report on the auto-detection of devices connected to the onboard SATA drive connectors. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset AHCI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > AHCI Port0 [Not Detected] > AHCI Port1 [Not Detected] Exit Some SATA CD/DVD in AHCI mode need to wait ready longer ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.
KINO-GM45A Mini-ITX SBC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset AHCI Port0 ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Device :Not Detected ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ SATA Port0 [Auto] S.M.A.R.T. [Enabled] Power Exit Select the type of device connected to the system ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
KINO-GM45A Mini-ITX SBC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Configure Remote Access type and parameters ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Remote Access [Disabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
KINO-GM45A Mini-ITX SBC Î COM2 System is remotely accessed through COM2 Î COM3 System is remotely accessed through COM3 Î COM4 System is remotely accessed through COM4 NOTE: Make sure the selected COM port is enabled through the Super I/O configuration menu. Î Base Address, IRQ [3E8h, A] The Base Address, IRQ option cannot be configured and only shows the interrupt address of the serial port listed above.
KINO-GM45A Mini-ITX SBC Î Redirection is active during POST and during Boot Boot Loader Loader Î Always DEFAULT Redirection is always active (Some OSes may not work if set to Always) Î Terminal Type [ANSI] Use the Terminal Type BIOS option to specify the remote terminal type. Î ANSI Î VT100 The target terminal type is VT100 Î VT-UTF8 The target terminal type is VT-UTF8 DEFAULT The target terminal type is ANSI 5.3.
KINO-GM45A Mini-ITX SBC Î Module Version: x.xxxxx.xxxxx USB Devices Enabled The USB Devices Enabled field lists the USB devices that are enabled on the system Î USB Function [Enabled] Use the USB Function BIOS option to enable or disable USB function support. Î Î Disabled Î Enabled USB function support disabled DEFAULT USB function support enabled USB 2.0 Controller [Enabled] The USB 2.0 Controller BIOS option is enabled.
KINO-GM45A Mini-ITX SBC Î HiSpeed DEFAULT The controller is capable of operating at 480 Mb/s 5.3.8 Power Configuration The Power Configuration menu (BIOS Menu 12) allows the advanced power management options to be configured.
KINO-GM45A Mini-ITX SBC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset ACPI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Suspend mode [S1 (POS)] Exit Set the ACPI state used for System suspend ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
KINO-GM45A Mini-ITX SBC 5.4 PCI/PnP Use the PCI/PnP menu (BIOS Menu 14) to configure advanced PCI and PnP settings. WARNING! Setting wrong values for the BIOS selections in the PCIPnP BIOS menu may cause the system to malfunction.
KINO-GM45A Mini-ITX SBC Î Available DEFAULT The specified IRQ is available to be used by PCI/PnP devices Î The specified IRQ is reserved for use by Legacy ISA Reserved devices Available IRQ addresses are: Î IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device.
KINO-GM45A Mini-ITX SBC Î Reserved Memory Size [Disabled] Use the Reserved Memory Size BIOS option to specify the amount of memory that should be reserved for legacy ISA devices. Î Disabled Î 16K 16 KB reserved for legacy ISA devices Î 32K 32 KB reserved for legacy ISA devices Î 64K 54 KB reserved for legacy ISA devices DEFAULT No memory block reserved for legacy ISA devices 5.5 Boot Use the Boot menu (BIOS Menu 15) to configure system boot options.
KINO-GM45A Mini-ITX SBC 5.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 16) to configure advanced system boot options. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Boot Settings Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Quick Boot [Enabled] Quiet Boot [Enabled] AddOn ROM Display Mode [Force BIOS] Bootup Num-Lock [On] RTL8111CP LAN Support [Disabled] Exit Allows BIOS to skip certain tests while booting.
KINO-GM45A Mini-ITX SBC Î AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. Î Force BIOS The system forces third party BIOS to display DEFAULT during system boot. Î The system displays normal information during Keep Current system boot. Î Bootup Num-Lock [On] Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be modified during boot up.
KINO-GM45A Mini-ITX SBC 5.6 Security Use the Security menu (BIOS Menu 17) to set system and user passwords. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Security Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Supervisor Password :Not Installed User Password :Not Installed Change Supervisor Password Change User Password ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
KINO-GM45A Mini-ITX SBC 5.7 Chipset Use the Chipset menu (BIOS Menu 18) to access the Northbridge and Southbridge configuration menus WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Advanced Chipset Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below section may cause system to malfunction.
KINO-GM45A Mini-ITX SBC 5.7.1 Northbridge Configuration Use the Northbridge Chipset Configuration menu (BIOS Menu 19) to configure the Northbridge chipset.
KINO-GM45A Mini-ITX SBC Î Boots Graphics Adapter [IGD] Use the Boots Graphics Adapter option to select the graphics controller used as the primary boot device. Select either an integrated graphics controller (IGD) or a combination of PCI graphics controller, a PCI express (PEG) controller or an IGD.
KINO-GM45A Mini-ITX SBC 640 x 480 18b 800 x 600 18b 1024 x 768 18b 1280 x 768 24b 1280 x 1024 48b 1600 x 1200 48b BY HARDWARE DEFAULT 5.7.2 Southbridge Configuration The Southbridge Configuration menu (BIOS Menu 20) the Southbridge chipset to be configured.
KINO-GM45A Mini-ITX SBC Î Restore on AC Power Loss [Last State] Use the Restore on AC Power Loss BIOS option to specify what state the system returns to if there is a sudden loss of power to the system. Î Power Off The system remains turned off Î Power On The system turns on Î Last State DEFAULT The system returns to its previous state. If it was on, it turns itself on. If it was off, it remains off. Î Spread Spectrum [Disabled] Use the Spread Spectrum option to reduce the EMI.
KINO-GM45A Mini-ITX SBC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Options ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Load Failsafe Defaults Exit Exit system setup after saving the changes. F10 key can be used for this operation ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
KINO-GM45A Mini-ITX SBC Appendix A A BIOS Menu Options Page 103
KINO-GM45A Mini-ITX SBC System Overview .................................................................................................................70 System Time [xx:xx:xx] .......................................................................................................71 System Date [xx/xx/xx] ........................................................................................................71 SATA#1 Configurations [Compatible] .............................................................
KINO-GM45A Mini-ITX SBC USB2.0 Controller Mode [HiSpeed]....................................................................................88 Suspend Mode [S1(POS)]....................................................................................................90 IRQ# [Available] ...................................................................................................................91 DMA Channel# [Available] ....................................................................................
KINO-GM45A Mini-ITX SBC Appendix B B Terminology Page 106
KINO-GM45A Mini-ITX SBC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
KINO-GM45A Mini-ITX SBC computer is usually a male DE-9 connector. DAC The Digital-to-Analog Converter (DAC) converts digital signals to analog signals. DDR Double Data Rate refers to a data bus transferring data on both the rising and falling edges of the clock signal. DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory.
KINO-GM45A Mini-ITX SBC MAC The Media Access Control (MAC) protocol enables several terminals or network nodes to communicate in a LAN, or other multipoint networks. PCIe PCI Express (PCIe) is a communications bus that uses dual data lines for full-duplex (two-way) serial (point-to-point) communications between the SBC components and/or expansion cards and the SBC chipsets. Each line has a 2.5 Gbps data transmission rate and a 250 MBps sustained data transfer rate.
KINO-GM45A Mini-ITX SBC USB The Universal Serial Bus (USB) is an external bus standard for interfacing devices. USB 1.1 supports 12Mbps data transfer rates, while USB 2.0 supports 480Mbps data transfer rates. VGA The Video Graphics Array (VGA) is a graphics display system developed by IBM.
KINO-GM45A Mini-ITX SBC Appendix C C Watchdog Timer Page 111
KINO-GM45A Mini-ITX SBC NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
KINO-GM45A Mini-ITX SBC NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
KINO-GM45A Mini-ITX SBC Appendix D D Hazardous Materials Disclosure Page 114
KINO-GM45A Mini-ITX SBC D.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
KINO-GM45A Mini-ITX SBC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X X O O O O O X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O Board Metal Fasteners Cable Assembly Assemblies Battery O O: This toxic or ha
KINO-GM45A Mini-ITX SBC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些 元件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下
