Owner's manual

ManualsBrandsIEI Integration ManualsComputer AccessoriesECN-360A-D2550

ECN-360A-D2550 Embedded System

Page i

IEI Technology Corp.

User Manual

MODEL:

ECN-360A-D2550

Embedded System with Intel® dual core Atom™ D2550 Processor,

Tw o VGA, Six USB 2.0, Four COM,

GbE and RoHS Compliant

Rev. 1.00 – 1 July 2013

Summary of content (141 pages)

PAGE 1
ECN-360A-D2550 Em b e d d e d S ys te m , IEI Te c h n o lo g y Co rp . MODEL: ECN-360A-D2550 Em b e d d e d S ys te m with In te l® d u a l c o re Ato m ™ D2550 P ro c e s s o r, Two VGA, S ix US B 2.0, Fo u r COM, Gb E a n d Ro HS Co m p lia n t Us e r Ma n u a l Page i Re v. 1.
PAGE 2
ECN-360A-D2550 Em b e d d e d S ys te m Re vis io n Date Version Changes 1 July 2013 1.
PAGE 3
ECN-360A-D2550 Em b e d d e d S ys te m Co p yrig h t COP YRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
ECN-360A-D2550 Em b e d d e d S ys te m Ta b le o f Co n te n ts 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.2 MODEL VARIATIONS ................................................................................................... 2 1.3 FEATURES ..........................................................
PAGE 5
ECN-360A-D2550 Em b e d d e d S ys te m 4.1.3 External Interface Panel Connectors............................................................... 25 4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 26 4.2.1 5 V SATA Power Connectors ............................................................................ 26 4.2.2 Audio Connector .............................................................................................. 26 4.2.
PAGE 6
ECN-360A-D2550 Em b e d d e d S ys te m 5.2 MAIN ........................................................................................................................ 50 5.3 ADVANCED ............................................................................................................... 51 5.3.1 ACPI Settings ................................................................................................... 51 5.3.2 RTC Wake Settings ................................................................
PAGE 7
ECN-360A-D2550 Em b e d d e d S ys te m C.2 SETUP PROCEDURE FOR WINDOWS .......................................................................... 87 C.2.1 Hardware and BIOS Setup .............................................................................. 88 C.2.2 Create Partitions ............................................................................................. 88 C.2.3 Install Operating System, Drivers and Applications ....................................... 92 C.2.
PAGE 8
ECN-360A-D2550 Em b e d d e d S ys te m Lis t o f Fig u re s Figure 1-1: ECN-360A-D2550 .........................................................................................................2 Figure 1-2: ECN-360A-D2550 Front Panel ....................................................................................5 Figure 1-3: ECN-360A-D2550 Rear Panel .....................................................................................6 Figure 1-4: Physical Dimensions (mm) .............................
PAGE 9
ECN-360A-D2550 Em b e d d e d S ys te m Figure 4-17: USB Connector Location........................................................................................39 Figure 4-18: External Peripheral Interface Connector ..............................................................40 Figure 4-19: RJ-45 Ethernet Connector ......................................................................................41 Figure 4-20: VGA Connector ..........................................................................
PAGE 10
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-28: Press any key to continue ...................................................................................103 Figure C-29: Partitions for Linux...............................................................................................105 Figure C-30: Manual Recovery Environment for Linux ..........................................................106 Figure C-31: Access menu.lst in Linux (Text Mode) ...................................................
PAGE 11
ECN-360A-D2550 Em b e d d e d S ys te m Lis t o f Ta b le s Table 1-1: Model Variations ...........................................................................................................2 Table 1-2: Technical Specifications ..............................................................................................4 Table 2-1: Package List Contents ...............................................................................................11 Table 4-1: Peripheral Interface Connectors ........
PAGE 12
ECN-360A-D2550 Em b e d d e d S ys te m Ch a p te r 1 1 In tro d u c tio n Page 1
PAGE 13
ECN-360A-D2550 Em b e d d e d S ys te m 1.1 Ove rvie w Figure 1-1: ECN-360A-D2550 The ECN-360A-D2550 embedded system is a fanless system with two VGA ports for dual display. It is powered by Intel® dual core Atom™ D2550 processor and supports one 204-pin DDR3 SDRAM SO-DIMM module up to 4 GB (2GB memory preinstalled). The ECN-360A-D2550 supports a 2.5” SATA HDD with up to 3 Gb/s data transfer rate. Four serial ports and six USB 2.
PAGE 14
ECN-360A-D2550 Em b e d d e d S ys te m 1.4 Te c h n ic a l Sp e c ific a tio n s The ECN-360A-D2550 technical specifications are listed in Table 1-1. Ch a s s is Co lo r Black Dim e n s io n ( WxDxH) 255 x 130 x 63 S ys te m Fa n Fanless Ch a s s is Co n s tru c tio n SECC Mo th e rb o a rd Mo th e rb o a rd m o d e l NANO-CV-D25502 CP U Intel® dual core Atom™ D2550 1.
PAGE 15
ECN-360A-D2550 Em b e d d e d S ys te m 1 x Full size (support mSATA) P CIe Min i 1 x Half size P o we r 9~28V DC P o we r In p u t Power 1 : DC Jack Power 2: Terminal block P o we r Co n s u m p tio n 12V@1.
PAGE 16
ECN-360A-D2550 Em b e d d e d S ys te m Figure 1-2: ECN-360A-D2550 Front Panel 1.6 Re a r P a n e l The rear panel of the ECN-360A-D2550 has the following features (Figure 1-3):  1 x Line-out  1 x 9 V ~ 28 V power jack  1 x Reset button  2 x RJ-45 LAN connectors  3 x RS-232 (DB-9 connector)  1 x RS-422/485 (DB-9 connector)  1 x 9 V ~ 28 V terminal block  4 x USB 2.
PAGE 17
ECN-360A-D2550 Em b e d d e d S ys te m Figure 1-3: ECN-360A-D2550 Rear Panel Page 6
PAGE 18
ECN-360A-D2550 Em b e d d e d S ys te m 1.
PAGE 19
ECN-360A-D2550 Em b e d d e d S ys te m Ch a p te r 2 2 Un p a c kin g Page 8
PAGE 20
ECN-360A-D2550 Em b e d d e d S ys te m 2.1 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during installation may result in permanent damage to the ECN-360A-D2550 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the ECN-360A-D2550. Dry climates are especially susceptible to ESD.
PAGE 21
ECN-360A-D2550 Em b e d d e d S ys te m 2.3 Un pa c kin g Ch e c klis t NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the ECN-360A-D2550 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw.
PAGE 22
ECN-360A-D2550 Em b e d d e d S ys te m Qu a n tity Ite m a n d P a rt Nu m b e r 1 Utility CD 1 One Key Recovery CD Im a g e Table 2-1: Package List Contents P a g e 11
PAGE 23
ECN-360A-D2550 Em b e d d e d S ys te m Ch a p te r 3 3 In s ta lla tio n P a g e 12
PAGE 24
ECN-360A-D2550 Em b e d d e d S ys te m 3.1 In s ta lla tio n P re c a u tio n s During installation, be aware of the precautions below:  Read the user manual: The user manual provides a complete description of the ECN-360A-D2550, installation instructions and configuration options.  DANGER! Disconnect Power: Power to the ECN-360A-D2550 must be disconnected during the installation process, or before any attempt is made to access the rear panel.
PAGE 25
ECN-360A-D2550 Em b e d d e d S ys te m S te p 1: Remove six retention screws from the bottom panel (Figure 3-1). Figure 3-1: Retention Screws Removal S te p 2: Open the bottom panel and locate the HDD bracket (Figure 3-2).
PAGE 26
ECN-360A-D2550 Em b e d d e d S ys te m S te p 3: Attach the HDD to the HDD bracket, and then slide the HDD to connect the HDD to the SATA connector. Secure the HDD with the HDD bracket by four retention screws (Figure 3-3). Figure 3-3: HDD Retention Screws S te p 4: Replace the HDD cover and secure it using six previously removed retention screws. 3.
PAGE 27
ECN-360A-D2550 Em b e d d e d S ys te m Figure 3-4: Wi-Fi Antenna Installation 3.5 Mo u n t th e S ys te m To mount the embedded system onto a wall or some other surface using the two mounting brackets, please follow the steps below. S te p 1: Turn the embedded system over. S te p 2: Align the two retention screw holes in each bracket with the corresponding retention screw holes on the sides of the bottom surface.
PAGE 28
ECN-360A-D2550 Em b e d d e d S ys te m Align the mounting holes in the sides of the mounting brackets with the predrilled S te p 5: holes in the mounting surface. NOTE: To have the best system heat dissipation, please make sure to face the I/O panel downward (Figure 3-5) when mounting the system. Insert four retention screws, two in each bracket, to secure the system to the S te p 6: wall. S te p 0: 3.
PAGE 29
ECN-360A-D2550 Em b e d d e d S ys te m S te p 2: Plug the audio plug into the audio jack. Plug the audio plug into the audio jack. If the plug on your speakers is different, an adapter will need to be used to plug them into the audio jack. The audio jack on the ECN-360A-D2550 is a line-out port which connects to a headphone or a speaker. Figure 3-6: Audio Connector S te p 3: Check audio clarity.
PAGE 30
ECN-360A-D2550 Em b e d d e d S ys te m Figure 3-7: LAN Connection S te p 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the RJ-45 connector. S te p 0: 3.6.3 DB-9 S e ria l P o rt Co n n e c tio n There are three RS-232 DB-9 connectors and one RS-422/485 DB-9 connector of the ECN-360A-D2550 for serial device connection. Follow the steps below to connect a serial device to the DB-9 connector of the ECN-360A-D2550.
PAGE 31
ECN-360A-D2550 Em b e d d e d S ys te m Figure 3-8: DB-9 Serial Port Connector S te p 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. Step 0: 3.6.4 US B De vic e Co n n e c tio n NOTE: User must install the USB 3.0 driver before connecting a USB device to the system or else the system may not recognize the connected device. There are six USB 2.0 connectors on the ECN-360A-D2550.
PAGE 32
ECN-360A-D2550 Em b e d d e d S ys te m Figure 3-9: USB Device Connection S te p 3: Insert the device connector. Once aligned, gently insert the USB device connector into the onboard connector. 3.6.5 VGA Mo n ito r Co n n e c tio n The ECN-360A-D2550 has two female DB-15 connectors on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the ECN-360A-D2550, please follow the instructions below.
PAGE 33
ECN-360A-D2550 Em b e d d e d S ys te m Figure 3-10: VGA Connector S te p 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector.
PAGE 34
ECN-360A-D2550 Em b e d d e d S ys te m Ch a p te r 4 4 S ys te m Mo th e rb o a rd P a g e 23
PAGE 35
ECN-360A-D2550 Em b e d d e d S ys te m 4.1 P e rip h e ra l In te rfa c e Co n n e c to rs This chapter details all the jumpers and connectors. 4.1.1 La yo u t The figure below shows all the connectors and jumpers. Figure 4-1: Connectors and Jumpers 4.1.2 P e rip h e ra l In te rfa c e Co n n e c to rs The table below lists all the connectors on the board.
PAGE 36
ECN-360A-D2550 Em b e d d e d S ys te m Co n n e c to r Typ e La b e l Backlight inverter connector 5-pin wafer INV1 Battery connector 2-pin wafer CN1 Digital Input/Output (DIO) connector 10-pin header DIO1 Fan connectors 3-pin wafer CPU_FAN1, SYS_FAN2 Front panel connector 10-pin header F_PANEL1 Keyboard and mouse connector 6-pin wafer KB_MS1 LVDS connector 20-pin crimp LVDS1 PCIe Mini card slots 52-pin PCIe Mini M_PCIE1, M_PCIE2 Power connector (9V~28V) 4-pin connector CN2 RS
PAGE 37
ECN-360A-D2550 Em b e d d e d S ys te m 4.2 In te rn a l P e rip h e ra l Co n n e c to rs The section describes all of the connectors on the motherboard. 4.2.1 5 V S ATA P o we r Co n n e c to rs CN La b e l: S ATA_P WR1, S ATA_P WR2 CN Typ e : 2-pin wafer CN Lo c a tio n : See Figure 4-2 CN P in o u ts : See Table 4-3 Use the 5 V SATA power connectors to connect to SATA device power connection. Figure 4-2: 5 V SATA Power Connector Locations Pin No.
PAGE 38
ECN-360A-D2550 Em b e d d e d S ys te m The 10-pin audio connector is connected to external audio devices including speakers and microphones for the input and output of audio signals to and from the system. Figure 4-3: Audio Connector Location Pin Description Pin Description 1 SPK_R 2 LINE1_R 3 AUD_GND 4 AUD_GND 5 SPK _L 6 LINE1_L 7 AUD_GND 8 AUD_GND 9 MIC1_R 10 MIC1_L Table 4-4: Audio Connector Pinouts 4.2.
PAGE 39
ECN-360A-D2550 Em b e d d e d S ys te m Figure 4-4: Backlight Inverter Connector Location Pin Description 1 LCD_BKLTCTL 2 GROUND 3 +12V 4 GROUND 5 BACKLIGHT ENABLE Table 4-5: Backlight Inverter Connector Pinouts 4.2.4 Ba tte ry Co n n e c to r CN La b e l: CN1 CN Typ e : 2-pin wafer CN Lo c a tio n : See Figure 4-5 CN P in o u ts : See Table 4-6 This is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off.
PAGE 40
ECN-360A-D2550 Em b e d d e d S ys te m Figure 4-5: Battery Connector Location Pin Description 1 Battery+ 2 GND Table 4-6: Battery Connector Pinouts 4.2.5 Dig ita l In p u t/Ou tp u t (DIO) Co n n e c to r CN La b e l: DIO1 CN Typ e : 10-pin header CN Lo c a tio n : See Figure 4-6 CN P in o u ts : See Table 4-7 The digital input/output connector is managed through a Super I/O chip. The DIO connector pins are user programmable.
PAGE 41
ECN-360A-D2550 Em b e d d e d S ys te m Pin Description Pin Description 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input 3 8 Input 2 9 Input 1 10 Input 0 Table 4-7: Digital I/O Connector Pinouts 4.2.6 Fa n Co n n e c to rs CN La b e l: CP U_FAN1, S YS _FAN1 CN Typ e : 3-pin wafer CN Lo c a tio n : See Figure 4-7 CN P in o u ts : See Table 4-8 The fan connectors attach to the CPU/system cooling fans. Figure 4-7: Fan Connector Locations PIN NO.
PAGE 42
ECN-360A-D2550 Em b e d d e d S ys te m 4.2.7 Fro n t P a n e l Co n n e c to r CN La b e l: F_P ANEL1 CN Typ e : 10-pin header CN Lo c a tio n : See Figure 4-8 CN P in o u ts : See Table 4-9 The front panel connector connects to the indicator LEDs and buttons on the computer's front panel.
PAGE 43
ECN-360A-D2550 Em b e d d e d S ys te m The keyboard and mouse connector can be connected to a standard PS/2 cable or PS/2 Y-cable to add keyboard and mouse functionality to the system. Figure 4-9: Keyboard/Mouse Connector Location Pin Description 1 VCC 2 Mouse Data 3 Mouse Clock 4 Keyboard Data 5 Keyboard Clock 6 GND Table 4-10: Keyboard/Mouse Connector Pinouts 4.2.
PAGE 44
ECN-360A-D2550 Em b e d d e d S ys te m Figure 4-10: LVDS1 Connector Location Pin Description Pin Description 1 GND 2 GND 3 LVDS_DATA0 4 LVDS_DATA0# 5 LVDS_DATA1 6 LVDS_DATA1# 7 LVDS_DATA2 8 LVDS_DATA2# 9 LVDS_CLK 10 LVDS_CLK# 11 NC 12 NC 13 GND 14 GND 15 LDDC_DATA 16 LDDC_CLK 17 VCC_LCD 18 VCC_LCD 19 VCC_LCD 20 VCC_LCD Table 4-11: LVDS1 Connector Pinouts 4.2.
PAGE 45
ECN-360A-D2550 Em b e d d e d S ys te m NOTE: The M_PCIE1 slot supports mSATA devices. However, the SATA1 connector will be disabled when an mSATA device is installed to the M_PCIE1 slot. Figure 4-11: PCIe Mini Card Slot Locations Pin Description Pin Description 1 PCIE_WAKE# 2 VCC3 3 N/C 4 GND 5 N/C 6 1.
PAGE 46
ECN-360A-D2550 Em b e d d e d S ys te m Pin Description Pin Description 29 GND 30 SMBCLK 31 PCIE_TXN 32 SMBDATA 33 PCIE_TXP 34 GND 35 GND 36 USBD- 37 GND 38 USBD+ 39 VCC3 40 GND 41 VCC3 42 N/C 43 GND 44 N/C 45 N/C 46 N/C 47 N/C 48 1.5V 49 N/C 50 GND 51 M-SATA Detect 52 VCC3 Table 4-12: PCIe Mini Card Slot Pinouts 4.2.
PAGE 47
ECN-360A-D2550 Em b e d d e d S ys te m Pin Description Pin Description 1 GND 2 GND 3 PWR 4 PWR Table 4-13: Power Connector Pinouts 4.2.12 RS -232 S e ria l P o rt Co n n e c to rs CN La b e l: COM1, COM2, COM3 CN Typ e : 10-pin header CN Lo c a tio n : See Figure 4-13 CN P in o u ts : See Table 4-14 Each of these connectors provides RS-232 connections.
PAGE 48
ECN-360A-D2550 Em b e d d e d S ys te m 4.2.13 RS -422/485 S e ria l P ort Co n n e c to r CN La b e l: COM4 CN Typ e : 4-pin wafer CN Lo c a tio n : See Figure 4-14 CN P in o u ts : See Table 4-15 This connector provides RS-422 or RS-485 communications. Figure 4-14: RS-422/485 Connector Location Pin Description Pin Description 1 RXD422- 3 TXD422+/TXD485+ 2 RXD422+ 4 TXD422-/TXD485- Table 4-15: RS-422/485 Connector Pinouts 4.2.
PAGE 49
ECN-360A-D2550 Em b e d d e d S ys te m NOTE: The SATA1 connector will be disabled when an mSATA device is installed to the M_PCIE1 slot. Figure 4-15: SATA Drive Connector Locations Pin Description 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND Table 4-16: SATA Drive Connector Pinouts 4.2.15 S O-DIMM Co n n e c to r CN La b e l: DIMM1 CN Typ e : 204-pin DDR3 SO-DIMM connector CN Lo c a tio n : See Figure 4-16 The SO-DIMM connector is for installing memory on the system.
PAGE 50
ECN-360A-D2550 Em b e d d e d S ys te m Figure 4-16: SO-DIMM Connector Location 4.2.16 US B Co n n e c to r CN La b e l: US B4 CN Typ e : 8-pin header CN Lo c a tio n : See Figure 4-17 CN P in o u ts : See Table 4-17 The USB connector provides connectivity to two USB 1.1/2.0 ports.
PAGE 51
ECN-360A-D2550 Em b e d d e d S ys te m 4.3 Exte rn a l P e rip h e ra l In te rfa c e Co n n e c to r P a n e l The figure below shows the external periphe4ral interface connector (EPIC) panel. The EPIC panel consists of the following: Figure 4-18: External Peripheral Interface Connector 4.3.
PAGE 52
ECN-360A-D2550 Em b e d d e d S ys te m Figure 4-19: RJ-45 Ethernet Connector LED Description LED Description A on: linked B off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 4-19: RJ-45 Ethernet Connector LEDs 4.3.2 US B Co n n e c to rs CN La b e l: US B_CON2, US B_CON3 CN Typ e : Dual USB 2.0 port CN Lo c a tio n : See Figure 4-18 CN P in o u ts : See Table 4-20 The ports connect to both USB 2.0 and USB 1.1 devices.
PAGE 53
ECN-360A-D2550 Em b e d d e d S ys te m 4.3.3 VGA Co n n e c to rs CN La b e l: VGA1, VGA2 CN Typ e : 15-pin Female CN Lo c a tio n : See Figure 4-18 CN P in o u ts : See Table 4-21 and Figure 4-20 Each VGA connector connects to a monitor that accepts a standard VGA input.
PAGE 54
ECN-360A-D2550 Em b e d d e d S ys te m 4.4 J u m p e r S e ttin g s NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper. The jumpers on the motherboard are listed in Table 4-22.
PAGE 55
ECN-360A-D2550 Em b e d d e d S ys te m Setting Description Off Use AT power Table 4-23: AT/ATX Power Selection Jumper Settings Figure 4-21: AT/ATX Power Selection Jumper Location 4.4.2 Cle a r CMOS J u m p e r J u m p e r La b e l: J P2 J u m p e r Typ e : 3-pin header J u m p e r S e ttin g s : See Table 4-24 J u m p e r Lo c a tio n : See Figure 4-22 To reset the BIOS, move the jumper to the "Clear BIOS" position for 3 seconds or more, and then move back to the default position.
PAGE 56
ECN-360A-D2550 Em b e d d e d S ys te m Figure 4-22: Clear CMOS Jumper Location 4.4.3 LVDS 1 Vo lta g e S e le c tio n WARNING: Permanent damage to the screen and ECN-360A-D2550 may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that came with the monitor to select the correct voltage.
PAGE 57
ECN-360A-D2550 Em b e d d e d S ys te m Figure 4-23: LVDS1 Voltage Selection Jumper Location 4.4.4 m S ATA/P CIe Min i S e le c tio n J u m p e r La b e l: MSATA_SW1 J u m p e r Typ e : 2-pin header J u m p e r S e ttin g s : See Table 4-26 J u m p e r Lo c a tio n : See Figure 4-24 The mSATA/PCIe Mini mode selection jumper specifies the M_PCIE1 connector as MSATA or PCIe Mini mode.
PAGE 58
ECN-360A-D2550 Em b e d d e d S ys te m Ch a p te r 5 5 BIOS P a g e 47
PAGE 59
ECN-360A-D2550 Em b e d d e d S ys te m 5.1 In tro d u c tio n The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Sta rtin g S e tu p The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DEL or F2 key as soon as the system is turned on or 2.
PAGE 60
ECN-360A-D2550 Em b e d d e d S ys te m Ke y Fu n c tio n Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu F1 General help, only for Status Page Setup Menu and Option Page Setup Menu F2 Load previous values F3 Load optimized defaults F4 Save changes and Exit BIOS Table 5-1: BIOS Navigation Keys 5.1.
PAGE 61
ECN-360A-D2550 Em b e d d e d S ys te m 5.2 Ma in The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliancy Project Version Build Date and Time American Megatrends 4.6.5.3 0.16 UEFI 2.3; PI 1.2 B239AR10.ROM 05/11/2012 11:53:40 Set the Date.
PAGE 62
ECN-360A-D2550 Em b e d d e d S ys te m  S ys te m Tim e [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Ad va n c e d Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING: Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.
PAGE 63
ECN-360A-D2550 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced ACPI Settings ACPI Sleep State [S1 (CPU Stop Clock)] Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. ---------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 64
ECN-360A-D2550 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the date::hr::min::sec specified ---------------------- : Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 65
ECN-360A-D2550 Em b e d d e d S ys te m 5.3.3 CP U Co n fig u ra tio n Use the CPU Configuration menu (BIOS Menu 5) to view detailed CPU specifications and configure the CPU. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced CPU Configuration Processor Type EMT64 Processor Speed System Bus Speed Ratio Status Actual Ratio System Bus Speed Processor Stepping Microcode Revision L1 Cache RAM L2 Cache RAM Processor Core Hyper-Threading Intel(R) Atom(TM) CPU D2550 @ 1.
PAGE 66
ECN-360A-D2550 Em b e d d e d S ys te m  Hyp e r-Th re a d in g [En a b le d ] Use the Hyper-Threading BIOS option to enable or disable the Intel Hyper-Threading Technology.  Disabled  Enabled Disables the Intel Hyper-Threading Technology. DEFAULT Enables the Intel Hyper-Threading Technology. 5.3.4 IDE Co n fig u ra tio n Use the IDE Configuration menu (BIOS Menu 6) to change and/or set the configuration of the SATA devices installed in the system.
PAGE 67
ECN-360A-D2550 Em b e d d e d S ys te m 5.3.5 US B Co n fig u ra tio n Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced USB Configuration USB Devices: 1 Keyboard Legacy USB Support [Enabled] Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
PAGE 68
ECN-360A-D2550 Em b e d d e d S ys te m  Enabled  Auto Legacy USB support enabled DEFAULT Legacy USB support disabled if no USB devices are connected 5.3.6 F81866 S u pe r IO Co nfig u ra tio n Use the F81866 Super IO Configuration menu (BIOS Menu 8) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 69
ECN-360A-D2550 Em b e d d e d S ys te m 5.3.6.1 S e ria l P o rt n Co n fig u ra tio n Use the Serial Port n Configuration menu (BIOS Menu 9) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Serial Port n Configuration Serial Port Device Settings Enable or Disable Serial Port (COM) [Enabled] IO=3F8h; IRQ=4 --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 70
ECN-360A-D2550 Em b e d d e d S ys te m    IO=2F8h; Serial Port I/O port address is 2F8h and the interrupt IRQ=3, 4 address is IRQ3, 4 IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=3, 4 address is IRQ3, 4 IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=3, 4 address is IRQ3, 4 5.3.6.1.2 S e ria l P o rt 2 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.
PAGE 71
ECN-360A-D2550 Em b e d d e d S ys te m 5.3.6.1.3 S e ria l P o rt 3 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 72
ECN-360A-D2550 Em b e d d e d S ys te m 5.3.6.1.4 S e ria l P o rt 4 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 73
ECN-360A-D2550 Em b e d d e d S ys te m 5.3.7 F81866 H/W Mo n ito r The F81866 H/W Monitor menu (BIOS Menu 10) contains the fan configuration submenus and displays operating temperature, fan speeds and system voltages. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced PC Health Status Smart Fan Mode Select > Smart Fan Mode Configuration System Temperature CPU_FAN1 Speed SYS_FAN1 Speed +VCC_CPU +VCC_GFX +V1.05S +V1.5_DDR3 VSB5V +V3.
PAGE 74
ECN-360A-D2550 Em b e d d e d S ys te m o o VSB3V VBAT 5.3.7.1 S m a rt Fa n Mo d e Co nfig u ra tio n Use the Smart Fan Mode Configuration submenu (BIOS Menu 11) to configure fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 75
ECN-360A-D2550 Em b e d d e d S ys te m 5.3.8 S e ria l P o rt Co n s o le Re d ire c tio n The Serial Port Console Redirection menu (BIOS Menu 12) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 76
ECN-360A-D2550 Em b e d d e d S ys te m  Bits p e r s e c o n d [115200] Use the Bits per second option to specify the serial port transmission speed. The speed must match the other side. Long or noisy lines may require lower speeds.   9600 Sets the serial port transmission speed at 9600.  19200 Sets the serial port transmission speed at 19200.  38400 Sets the serial port transmission speed at 38400.  57600 Sets the serial port transmission speed at 57600.
PAGE 77
ECN-360A-D2550 Em b e d d e d S ys te m  Sto p Bits [1] Use the Stop Bits option to specify the number of stop bits used to indicate the end of a serial data packet. Communication with slow devices may require more than 1 stop bit.  1  2 DEFAULT Sets the number of stop bits at 1. Sets the number of stop bits at 2. 5.3.9 iEi Fe a tu re Use the iEi Feature menu (BIOS Menu 13) to configure One Key Recovery function. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 78
ECN-360A-D2550 Em b e d d e d S ys te m 5.4 Ch ips e t Use the Chipset menu (BIOS Menu 14) to access the Host Bridge and Southbridge configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 79
ECN-360A-D2550 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset > Intel IGD Configuration Config Intel IGD Settings ******* Memory Information ******* Memory Frequency 1067 MHz(DDR3) Total Memory 1024 MB DIMM#1 1024 MB --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 80
ECN-360A-D2550 Em b e d d e d S ys te m  IGFX - Bo o t Typ e [VBIOS De fa u lt] Use the IGFX - Boot Type option to select the display device used by the system when it boots. Configuration options are listed below.   VBIOS Default  CRT1  CRT2  LVDS1 DEFAULT LVDS 1 P a n e l Typ e [800x600 LVDS ] Use the LVDS1 Panel Type option to select the type of flat panel connected to the system. Configuration options are listed below.
PAGE 81
ECN-360A-D2550 Em b e d d e d S ys te m 5.4.2 S o u th Brid g e Co n fig u ra tio n Use the South Bridge Configuration menu (BIOS Menu 17) to configure the Southbridge chipset. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Auto Power Button Status [Disabled] Restore AC Power Loss Power Saving Function(ERP) Set Spread Spectrum function [Last State] [Disabled] [Disabled] Select AC power state when power is re-applied after a power failure.
PAGE 82
ECN-360A-D2550 Em b e d d e d S ys te m  S e t Sp re a d Sp e c tru m Fu n c tio n [Dis a b le d ] The Set Spread Spectrum Function option can help to improve CPU EMI issues.  Disabled  Enabled DEFAULT The spread spectrum mode is disabled The spread spectrum mode is enabled 5.5 Bo o t Use the Boot menu (BIOS Menu 18) to configure system boot options. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 83
ECN-360A-D2550 Em b e d d e d S ys te m  Does not enable the keyboard Number Lock Off automatically. To use the 10-keys on the keyboard, press the Number Lock key located on the upper left-hand corner of the 10-key pad. The Number Lock LED on the keyboard lights up when the Number Lock is engaged.  Qu ie t Bo o t [En a b le d ] Use the Quiet Boot BIOS option to select the screen display when the system boots.
PAGE 84
ECN-360A-D2550 Em b e d d e d S ys te m 5.6 S e c u rity Use the Security menu (BIOS Menu 19) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup.
PAGE 85
ECN-360A-D2550 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Reset the system after saving the changes. Restore Defaults Save as User Defaults Restore User Defaults --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219.
PAGE 86
ECN-360A-D2550 Em b e d d e d S ys te m Appendix A A S a fe ty P re c a u tio n s P a g e 75
PAGE 87
ECN-360A-D2550 Em b e d d e d S ys te m WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the ECN-360A-D2550. A.1 S a fe ty P re c a u tio n s Please follow the safety precautions outlined in the sections that follow: A.1.1 Ge n e ra l S a fe ty P re c a u tio n s Please ensure the following safety precautions are adhered to at all times.
PAGE 88
ECN-360A-D2550 Em b e d d e d S ys te m A.1.2 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during the installation of the ECN-360A-D2550 may result in permanent damage to the ECN-360A-D2550 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the ECN-360A-D2550. Dry climates are especially susceptible to ESD.
PAGE 89
ECN-360A-D2550 Em b e d d e d S ys te m A.1.3 P ro d u c t Dis p o s a l CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations.  Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
PAGE 90
ECN-360A-D2550 Em b e d d e d S ys te m  The interior of the ECN-360A-D2550X does not require cleaning. Keep fluids away from the ECN-360A-D2550 interior.  Be cautious of all small removable components when vacuuming the ECN-360A-D2550.  Turn the ECN-360A-D2550 off before cleaning the ECN-360A-D2550.  Never drop any objects or liquids through the openings of the ECN-360A-D2550.  Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the ECN-360A-D2550.
PAGE 91
ECN-360A-D2550 Em b e d d e d S ys te m Appendix B B BIOS Me n u Op tio n s P a g e 80
PAGE 92
ECN-360A-D2550 Em b e d d e d S ys te m  System Overview .................................................................................................................50  System Date [xx/xx/xx] ........................................................................................................50  System Time [xx:xx:xx] .......................................................................................................51  ACPI Sleep State [S1 (CPU Stop Clock)] ..........................
PAGE 93
ECN-360A-D2550 Em b e d d e d S ys te m  Bootup NumLock State [On] ...............................................................................................71  Quiet Boot [Enabled] ...........................................................................................................72  Launch PXE OpROM [Disabled] .........................................................................................72  Option ROM Messages [Force BIOS] .................................................
PAGE 94
ECN-360A-D2550 Em b e d d e d S ys te m Ap p e n d ix C C On e Ke y Re c o ve ry P a g e 83
PAGE 95
ECN-360A-D2550 Em b e d d e d S ys te m C.1 On e Ke y Re c o ve ry In tro d u c tio n The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 96
ECN-360A-D2550 Em b e d d e d S ys te m After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section C.5. NOTE: The initial setup procedures for Linux system are described in Section C.3. C.1.1 S ys te m Re q u ire m e n t NOTE: The recovery CD can only be used with IEI products.
PAGE 97
ECN-360A-D2550 Em b e d d e d S ys te m partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. C.1.
PAGE 98
ECN-360A-D2550 Em b e d d e d S ys te m o o o o o o o Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. C.2 S e tu p P ro c e d u re fo r Win d ows Prior to using the recovery tool to backup or restore, a few setup procedures are required. S te p 1: Hardware and BIOS setup (see Section C.2.1) S te p 2: Create partitions (see Section C.2.
PAGE 99
ECN-360A-D2550 Em b e d d e d S ys te m C.2.1 Ha rdwa re a n d BIOS S e tu p S te p 1: Make sure the system is powered off and unplugged. S te p 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended. S te p 3: Connect an optical disk drive to the system and insert the recovery CD. S te p 4: Turn on the system. S te p 5: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 100
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-2: Launching the Recovery Tool S te p 3: The recovery tool setup menu is shown as below. Figure C-3: Recovery Tool Setup Menu S te p 4: Press <6> then .
PAGE 101
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-4: Command Prompt S te p 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 102
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-5: Partition Creation Commands P a g e 91
PAGE 103
ECN-360A-D2550 Em b e d d e d S ys te m NOTE: Use the following commands to check if the partitions were created successfully. S te p 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.Step0: C.2.3 In s ta ll Op e ra tin g S ys te m , Drive rs a n d Ap p lic a tio n s Install the operating system onto the unlabelled partition.
PAGE 104
ECN-360A-D2550 Em b e d d e d S ys te m C.2.4 Bu ild in g th e Re c o ve ry P a rtitio n S te p 1: Put the recover CD in the optical drive. S te p 2: Start the system. S te p 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-6: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <2> then .
PAGE 105
ECN-360A-D2550 Em b e d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section C.2.2 is hidden and the recovery tool is saved in this partition. Figure C-8: Building the Recovery Partition S te p 6: After completing the system configuration, press any key in the following window to reboot the system.
PAGE 106
ECN-360A-D2550 Em b e d d e d S ys te m C.2.5 Cre a te Fa c to ry De fa u lt Im a g e NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. S te p 1: Turn on the system. When the following screen displays (Figure C-10), press the key to access the recovery tool.
PAGE 107
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-12: About Symantec Ghost Window S te p 4: Use mouse to navigate to the option shown below (Figure C-13). Figure C-13: Symantec Ghost Path S te p 5: P a g e 96 Select the local source drive (Drive 1) as shown in Figure C-14. Then click OK.
PAGE 108
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-14: Select a Local Source Drive S te p 6: Select a source partition (Part 1) from basic drive as shown in Figure C-15. Then click OK. Figure C-15: Select a Source Partition from Basic Drive S te p 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure C-16). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 109
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-16: File Name to Copy Image to S te p 8: When the Compress Image screen in Figure C-17 prompts, click High to make the image file smaller.
PAGE 110
ECN-360A-D2550 Em b e d d e d S ys te m S te p 9: The Proceed with partition image creation window appears, click Yes to continue. Figure C-18: Image Creation Confirmation S te p 10: The Symantec Ghost starts to create the factory default image (Figure C-19). Figure C-19: Image Creation Complete S te p 11: When the image creation completes, a screen prompts as shown in Figure C-20. Click Continue and close the Ghost window to exit the program.
PAGE 111
ECN-360A-D2550 Em b e d d e d S ys te m S te p 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure C-21: Press Any Key to Continue C.3 Au to Re c o ve ry S e tu p P ro c e d u re The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 112
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-22: Auto Recovery Utility S te p 3: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-23: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <4> then .
PAGE 113
ECN-360A-D2550 Em b e d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition. In this process the partition created for recovery files in Section C.2.2 is hidden and the auto recovery tool is saved in this partition. Figure C-25: Building the Auto Recovery Partition S te p 6: After completing the system configuration, the following message prompts to confirm whether to create a factory default image.
PAGE 114
ECN-360A-D2550 Em b e d d e d S ys te m S te p 7: The Symantec Ghost starts to create the factory default image (Figure C-27). Figure C-27: Image Creation Complete S te p 8: After completing the system configuration, press any key in the following window to restart the system. Figure C-28: Press any key to continue S te p 9: Eject the One Key Recovery CD and restart the system. S te p 10: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 115
ECN-360A-D2550 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes. Please install Auto Recovery API service before enabling this function --------------------: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.
PAGE 116
ECN-360A-D2550 Em b e d d e d S ys te m S te p 1: Hardware and BIOS setup. Refer to Section C.2.1. S te p 2: Install Linux operating system. Make sure to install GRUB (v0.97 or earlier) MBR type and Ext3 partition type. Leave enough space on the hard drive to create the recover partition later. NOTE: If the Linux OS is not installed with GRUB (v0.97 or earlier) and Ext3, the Symantec Ghost may not function properly.
PAGE 117
ECN-360A-D2550 Em b e d d e d S ys te m DISKPART>sel disk 0 DISKPART>create part pri size= ___ DISKPART>assign letter=N DISKPART>exit system32>format N: /fs:ntfs /q /v:Recovery /y system32>exit S te p 4: Build the recovery partition. Press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient. When the recovery tool setup menu appears, type <3> and press (Figure C-30).
PAGE 118
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-31: Access menu.lst in Linux (Text Mode) S te p 6: Modify the menu.lst as shown below. S te p 7: The recovery tool menu appears. (Figure C-32) Figure C-32: Recovery Tool Menu S te p 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section C.2.5 to create a factory default image.
PAGE 119
ECN-360A-D2550 Em b e d d e d S ys te m C.5 Re c o ve ry To o l Fu n c tio n s After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section C.3 has been completed and the auto recovery function is enabled, the system will automatically restore from the factory default image without pressing the F3 key. The recovery tool main menu is shown below.
PAGE 120
ECN-360A-D2550 Em b e d d e d S ys te m WARNING: All data in the system will be deleted during the system recovery. Please backup the system files before restoring the system (either Factory Restore or Restore Backup). C.5.1 Fa c to ry Re s to re To restore the factory default image, please follow the steps below. S te p 1: Type <1> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.
PAGE 121
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-35: Recovery Complete Window C.5.2 Ba c ku p S ys te m To backup the system, please follow the steps below. S te p 1: Type <2> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure C-36: Backup System S te p 3: The screen shown in Figure C-37 appears when system backup is complete.
PAGE 122
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-37: System Backup Complete Window C.5.3 Re s to re Yo u r La s t Ba c ku p To restore the last system backup, please follow the steps below. S te p 1: Type <3> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure C-38: Restore Backup S te p 3: The screen shown in Figure C-39 appears when backup recovery is complete. Press any key to reboot the system.
PAGE 123
ECN-360A-D2550 Em b e d d e d S ys te m Figure C-39: Restore System Backup Complete Window C.5.4 Ma n u a l To restore the last system backup, please follow the steps below. S te p 1: Type <4> and press in the main menu. S te p 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure C-40: Symantec Ghost Window S te p 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 124
ECN-360A-D2550 Em b e d d e d S ys te m C.6 Re s to re S ys te m s fro m a Lin u x S e rve r thro u g h LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 125
ECN-360A-D2550 Em b e d d e d S ys te m C.6.1 Co n fig u re DHCP S e rve r S e ttin g s S te p 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) S te p 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.
PAGE 126
ECN-360A-D2550 Em b e d d e d S ys te m filename “pxelinux.0”; C.6.2 Co n fig u re TFTP S e ttin g s S te p 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) S te p 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
PAGE 127
ECN-360A-D2550 Em b e d d e d S ys te m Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp C.6.3 Co n fig u re On e Ke y Re c o ve ry S e rve r S e ttin g s S te p 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). S te p 2: Extract the recovery package to /. #cp RecoveryR10.tar.
PAGE 128
ECN-360A-D2550 Em b e d d e d S ys te m C.6.4 Sta rt th e DHCP, TFTP a n d HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart C.6.5 Cre a te S ha re d Dire c to ry S te p 1: Install the samba. #yum install samba S te p 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
PAGE 129
ECN-360A-D2550 Em b e d d e d S ys te m Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 S te p 4: Edit “/etc/samba/smb.conf” for your environment. For example: S te p 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer C.6.6 S e tu p a Clie n t S ys te m fo r Au to Re c o ve ry S te p 1: Configure the following BIOS options of the client system.
PAGE 130
ECN-360A-D2550 Em b e d d e d S ys te m S te p 2: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1  remain the default setting to boot from the original OS. Boot Option #2  select the boot from LAN option. S te p 3: Save changes and exit BIOS menu. Exit  Save Changes and Exit S te p 4: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD.
PAGE 131
ECN-360A-D2550 Em b e d d e d S ys te m NOTE: A firewall or a SELinux is not in use in the whole setup process. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them.
PAGE 132
ECN-360A-D2550 Em b e d d e d S ys te m C.7 Oth e r In fo rm a tio n C.7.1 Us in g AHCI Mo d e o r ALi M5283 / VIA VT6421A Co n tro lle r When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery. Please follow the steps below to install the SATA RAID/AHCI driver. S te p 1: Copy the SATA RAID/AHCI driver to a floppy disk and insert the floppy disk into a USB floppy disk drive.
PAGE 133
ECN-360A-D2550 Em b e d d e d S ys te m S te p 5: When the following window appears, press ~~to select “Specify Additional Device”. S te p 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD.~~
~~PAGE 134~~
ECN-360A-D2550 Em b e d d e d S ys te m After pressing , the system will get into the recovery tool setup menu. S te p 7: Continue to follow the setup procedure from Step 4 in Section C.2.2 Create Partitions to finish the whole setup process.Step0: C.7.2 S ys te m Me m o ry Re q u ire m e n t To be able to access the recovery tool by pressing while booting up the system, please make sure to have enough system memory. The minimum memory requirement is listed below.
~~PAGE 135~~
~~ECN-360A-D2550 Em b e d d e d S ys te m Appendix D D Wa tc h d o g Tim e r P a g e 124~~
~~PAGE 136~~
ECN-360A-D2550 Em b e d d e d S ys te m NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
~~PAGE 137~~
~~ECN-360A-D2550 Em b e d d e d S ys te m NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.~~
~~PAGE 138~~
~~ECN-360A-D2550 Em b e d d e d S ys te m Ap p e n d ix E E Ha za rd o u s Ma te ria ls Dis c lo s u re P a g e 127~~
~~PAGE 139~~
ECN-360A-D2550 Em b e d d e d S ys te m E.1 Ha za rd o u s Ma te ria ls Dis c lo s u re Ta ble for IP B P ro d u c ts Ce rtifie d a s Ro HS Co m p lia n t Un d e r 2002/95/EC With o u t Me rc u ry The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 140~~
ECN-360A-D2550 Em b e d d e d S ys te m P a rt Na m e To xic o r Ha za rd o u s S u b s ta n c e s a n d Ele m e n ts Le a d Me rc u ry Ca d m iu m He xa va le n t P o lyb ro m in a te d P o lyb ro m in a te d (P b ) (Hg ) (Cd ) Ch ro m iu m Bip h e n yls Dip h e n yl (CR(VI)) (P BB) Eth e rs (P BDE) Ho u s in g X O O O O X Dis p la y X O O O O X P rin te d Circ u it X O O O O X X O O O O O X O O O O X Fa n As s e m b ly X O O O O X P o we r S u p p ly
~~PAGE 141~~
ECN-360A-D2550 Em b e d d e d S ys te m 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯 (P b ) (Hg ) (Cd ) (CR(VI)) (P BB) 醚 (P BDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 S