DM Series Monitor DM Series Industrial Monitor IEI Technology Corp. MODEL: DM Series 6.5”~19” LCD Monitor IP 65 Protection, VGA/DVI-D, 9-36V Input User Manual Page I Rev. 2.
DM Series Monitor Revision Date Version Changes 5 May, 2011 2.04 Added panel opening dimensions in Section 5.5.1 23 February, 2011 2.03 Minor changes 29 December, 2010 2.02 Updated Chapter 7 Software Drivers 09 December, 2010 2.01 Modified AV-6600 AD board information. Updated Chapter 6 OSD Controls section 15 June, 2010 2.00 Updated for DM-xx-R20 series 16 July, 2009 1.14 Updated “Chapter 6: OSD Controls” April, 2008 1.
DM Series Monitor Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
DM Series Monitor Table of Contents 1 INTRODUCTION........................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.2 FEATURES ................................................................................................................... 2 1.3 MODEL VARIATIONS ......................................................................
DM Series Monitor 2.4.3 DM-170 Physical Dimensions ......................................................................... 19 2.4.4 DM-150 Physical Dimensions ......................................................................... 20 2.4.5 DM-121 Physical Dimensions ......................................................................... 21 2.4.6 DM-104 Physical Dimensions ......................................................................... 22 2.4.7 DM-84 Physical Dimensions ......................
DM Series Monitor 4.4.1 AV-6600 Peripheral Interface Connectors....................................................... 43 4.4.2 AV-6600 Rear Panel Connectors ..................................................................... 44 5 INSTALLATION........................................................................................................... 45 5.1 INSTALLATION PRECAUTIONS ................................................................................... 46 5.2 UNPACKING ..........................
DM Series Monitor 6.1.1 OSD Buttons..................................................................................................... 75 6.1.2 OSD Menu Structure ........................................................................................ 76 6.2 USING THE OSD....................................................................................................... 78 6.2.1 Main Display Features..................................................................................... 78 6.2.2 Color ...
DM Series Monitor C.4.3 Image Page.................................................................................................... 106 C.4.4 Display Page (for analog signal) .................................................................. 107 C.4.5 Color Page .................................................................................................... 108 C.4.6 PIP Page........................................................................................................ 109 C.4.7 System Page.
DM Series Monitor List of Figures Figure 1 1: DM Series .....................................................................................................................2 Figure 1-2: Typical Monitor Front View ........................................................................................5 Figure 1-3: DM-190 Bottom Panel View ........................................................................................6 Figure 1-4: AV-6600 AD Board ...................................................
DM Series Monitor Figure 5-14: Insert the Monitor....................................................................................................59 Figure 5-15: Panel Mounting Clamp Position ............................................................................59 Figure 5-16: DM-65 Panel Opening (Unit: mm) ..........................................................................60 Figure 5-17: DM-65 Panel Mounting....................................................................................
DM Series Monitor Figure 8-1: Gasket Replacement.................................................................................................90 Figure 8-2: smartOSD Installer....................................................................................................99 Figure 8-3: smartOSD Welcome Screen.....................................................................................99 Figure 8-4: smartOSD Folder Select Screen...................................................................
DM Series Monitor List of Tables Table 1-1: DM Series Model Variations.........................................................................................3 Table 1-2: DM Series Specifications .............................................................................................9 Table 2-1: Front Panel Variants...................................................................................................11 Table 2-2: General Physical Dimensions ...............................................
DM Series Monitor Table C-1: SmartOSD Menu Structure.....................................................................................
DM Series Monitor Chapter 1 1 Introduction Page 1
DM Series Monitor 1.1 Overview Figure 1 1: DM Series The DM series LCD monitor is the latest member of IEI’s line of sophisticated LCD designs, and it has been improved to be RoHS compliant. It is designed to fit industrial automation, or any other applications that require minimum installation space and flexible configuration. The flat front panel provides IP 65 protection, which effectively wards off dust and water.
DM Series Monitor RoHS compliant 1.3 Model Variations The DM series LCD monitor has the following seven base models. DM-65: 6.5” LCD screen DM-84: 8.4” LCD screen DM-104: 10.4” LCD screen DM-121: 12.1” LCD screen DM-150: 15” LCD screen DM-170: 17” LCD screen DM-190: 19” LCD screen The DM series LCD monitor base models may or may not have a variety of variants.
DM Series Monitor 1.4 Applications The DM series LCD monitor is designed for rigorous industrial environments where it may be exposed to both heat and moisture. Its durability and strength also makes it an ideal choice for public access computers.
DM Series Monitor 1.5.1 Front View The front of the DM series LCD monitor is a flat panel LCD screen surrounded by an aluminum frame. A control button panel (OSD), if available, is located either vertically on the right side of the frame or horizontally along the bottom of the frame with the following control buttons: LCD On/Off Auto Left Right Menu The OSD panel also has one power LED. Figure 1-2 shows a typical monitor front view.
DM Series Monitor 1.5.2 Bottom Panel View Figure 1-3 shows the bottom panel of the DM-190 monitor. Other models may include or 5 exclude additional connectors. Refer to Section 2.3 for listings of monitors and their 5 connectors. All connectors are fully described in Section 5.4.
DM Series Monitor 1.5.3 AD Board The DM series LCD monitor AD board provides a wide variety of control interfaces, receiving and managing signals from a CPU card through cabling. Figure 1-4 shows the 5 AV-6600 AD board as a sample of a typical AD board for the DM series LCD monitor. Refer to Chapter 4 for a complete description of AD boards and their connectors.
DM Series Monitor 1.6 Series Specifications Table 1-2 shows the DM Series specifications. 5 Model LCD Size DM-65 DM-84 DM-104 DM-121 DM-150 DM-170 DM-190 6.5” 8.4” 10.4” 12.1” 15” 17” 19” VGA VGA VGA VGA VGA VGA VGA DVI-D DVI-D DVI-D DVI-D Input Interface Max. 640x480 800x600 800x600 1024x768 1024x768 1280x1024 1280x1024 800 450 400 500 350 300 300 Contrast 600:1 600:1 700:1 700:1 700:1 800:1 1000:1 LCD Color 262K 262K 262K 262K 16.2M 16.7M 16.
DM Series Monitor Model IP Level N/G Weight DM-65 DM-84 DM-104 DM-121 DM-150 DM-170 DM-190 IP 65 IP 65 IP 65 IP 65 IP 65 IP 65 IP 65 1kg 1.8kg 3kg 3.8kg 6kg 8.6kg 10kg Table 1-2: DM Series Specifications 1.7 Certifications All DM series LCD monitor models comply with the following international standards: RoHS IP 65 For a more detailed description of these standards, please refer to Appendix B.
DM Series Monitor Chapter 2 2 Mechanical Overview Page 10
DM Series Monitor 2.1 Introduction This chapter describes the general mechanical overview of the DM series monitors including front and bottom panel variations, available interfaces and overall dimensions. 2.2 Front Panel The front panel of the DM series LCD monitor is comprised of a LCD in an aluminum frame with an OSD control panel. 2.2.1 Front Panel Variants Table 2-1 shows the three front panel variants for the DM series LCD monitor.
DM Series Monitor 2.2.2 Front Panel Variant 1 The following models of the DM series LCD monitor have an OSD control panel located vertically along the right side of the aluminum frame: DM-170 DM-150 DM-121 DM-104 DM-84 Figure 2-1 shows the location of the front panel variant 1 OSD controls.
DM Series Monitor 2.2.3 Front Panel Variant 2 The following model of the DM series LCD monitor has an OSD control panel located horizontally along the bottom of the aluminum frame: DM-190 Figure 2-2 shows the location of the front panel variant 2 OSD controls.
DM Series Monitor 2.2.4 Front Panel Variant 3 The following model of the DM series LCD monitor has an OSD control panel located in-line along the bottom of the aluminum frame: DM-65 Figure 2-3 shows the location of the front panel variant 3 OSD controls. 5 Figure 2-3: Front Panel Variant 3 2.3 Bottom Panel All peripheral device connectors are located on the bottom panel of the DM series LCD monitor. The following sections describe the bottom panel variants and their associated connectors. 2.3.
DM Series Monitor 2.3.2 DM-65 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-65 series LCD monitor. VGA connector 12V power connector USB connector for touchscreen 2.3.3 DM-84 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-84 series LCD monitor. VGA connector 12V power connector 9~36V terminal block (M model only) 2.3.
DM Series Monitor USB connector for touchscreen 9~36V terminal block (M model only) 2.3.6 DM-150 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-150 series LCD monitor. VGA connector DVI-D connector 12V power connector RS-232 serial connector for touchscreen USB connector for touchscreen 9~36V terminal block (M model only) 2.3.
DM Series Monitor 2.4 Physical Dimensions The following sections describe the physical dimensions for each model of the DM series LCD monitor. 2.4.1 General Physical Dimensions General physical dimensions for the DM series LCD monitors are shown in Table 2-2. 5 Model Width Height Depth (mm) (mm) (mm) DM-190 482 399 73 DM-170 452 356 65.2 DM-150 410 309 64.
DM Series Monitor 2.4.2 DM-190 Physical Dimensions The physical dimensions of the DM-190 are shown in Figure 2-4.
DM Series Monitor 2.4.3 DM-170 Physical Dimensions The physical dimensions of the DM-170 are shown in Figure 2-5.
DM Series Monitor 2.4.4 DM-150 Physical Dimensions The physical dimensions of the DM-150 are shown in Figure 2-6.
DM Series Monitor 2.4.5 DM-121 Physical Dimensions The physical dimensions of the DM-121 are shown in Figure 2-7.
DM Series Monitor 2.4.6 DM-104 Physical Dimensions The physical dimensions of the DM-104 are shown in Figure 2-8.
DM Series Monitor 2.4.7 DM-84 Physical Dimensions The physical dimensions of the DM-84 are shown in Figure 2-9.
DM Series Monitor 2.4.8 DM-65 Physical Dimensions The physical dimensions of the DM-65 are shown in Figure 2-10.
DM Series Monitor 2.5 Optional Mounting Kits The following sections describe the various optional mounting kits available for each model of the DM series LCD monitor. Refer to Section 5.5 for detailed instructions on the different mounting methods for the monitors. CAUTION: Due to safety concerns, it is highly recommended to use the VESA mounting kits provided by IEI for wall, stand and arm mounting. If the VESA mounting kit is purchased separately, please make sure the mounting kit is UL-listed. 2.5.
DM Series Monitor LCD Monitor Arm ARM-11 LCD Monitor Stand STAND-100-RS Table 2-4: DM-84 Mounting Kits 2.5.3 DM-104 Mounting Kits Table 2-5 lists the mounting kits available for the DM-104 monitor. 5 Model DM-104 Panel Mounting Kit PK-104M Rack Mounting Kit RK-104MS-R10 Wall Mounting Kit WK-104MS-R10 DIN Mounting Kit - LCD Monitor Arm ARM-11 LCD Monitor Stand STAND-100-RS Table 2-5: DM-104 Mounting Kits 2.5.
DM Series Monitor 2.5.5 DM-150 Mounting Kits Table 2-7 lists the mounting kits available for the DM-150 monitor. 5 Model DM-150 Panel Mounting Kit PK-150M Rack Mounting Kit RK-150MS-R10 Wall Mounting Kit WK-150MS-R10 DIN Mounting Kit - LCD Monitor Arm ARM-31 LCD Monitor Stand STAND-100-RS Table 2-7: DM-150 Mounting Kits 2.5.6 DM-170 Mounting Kits Table 2-8 lists the mounting kits available for the DM-170 monitor.
DM Series Monitor 2.5.7 DM-190 Mounting Kits Table 2-9 lists the mounting kits available for the DM-190 monitor.
DM Series Monitor Chapter 3 3 LCD Specifications Page 29
DM Series Monitor 3.1 LCD Specifications 3.1.1 LCD Overview The DM series LCD monitors use the following LCD panels. DM-190: HANNSTAR/HSD190MEN3-A DM-170: AUO G170EG01 V0 DM-150: AUO G150XG01 V1 DM-121: AUO G121XN01 V0 DM-104: AUO/G104SN02 V2 DM-084: AUO/G084SN05 V8 DM-65: AUO/G065VN01 V2 Detailed specifications for the LCD screens are listed in the following sections.
DM Series Monitor 3.1.2 DM-190 LCD Specifications Table 3-1 lists the DM-190 LCD specifications. 5 Model DM-190 Size 19” MFR/Model HANNSTAR/HSD190MEN3-A Resolution SXGA (1280 x 1024) Active Area (mm) Pixel Pitch (mm) Mode Number of Colors Color Saturation (NTSC%) View Angle (H/V) Brightness (cd/m2) Contrast Ratio Response Time (ms) (at 25C) Interface Supply Voltage (V) Backlight 376.32 x 301.06 0.294 TN 16.
DM Series Monitor 3.1.3 DM-170 LCD Specifications Table 3-2 lists the DM-170 LCD specifications. 5 Model DM-170 Size 17” MFR/Model AUO/G170EG01 V0 Resolution SXGA (1280 x 1024) Active Area (mm) 337.9 x 270.3 Pixel Pitch (mm) Mode Number of Colors Color Saturation (NTSC%) View Angle (H/V) Brightness (cd/m2) Contrast Ratio Response Time (ms) (at 25C) Power Consumption (W) Interface Supply Voltage (V) 0.264 TN 16.7M 72 170/160 350 800:1 8 25.
DM Series Monitor 3.1.4 DM-150 LCD Specifications Table 3-3 lists the DM-150 LCD specifications. 5 Model DM-150 Size 15” MFR/Model AUO/G150XG01 V1 Resolution XGA (1024 x 768) Active Area (mm) 304.1 x 228.1 Pixel Pitch (mm) 0.297 Mode TN Number of Colors 16.2M Color Saturation (NTSC%) View Angle (H/V) 65 140/120 Brightness (cd/m2) 350 Contrast Ratio 700:1 Response Time (ms) (at 25C) 8 Power Consumption (W) Interface 8.9 1ch LVDS Supply Voltage (V) 3.
DM Series Monitor 3.1.5 DM-121 LCD Specifications Table 3-4 lists the DM-121 LCD specifications. 5 Model DM-121 Size 12.1” MFR/Model AUO/G121XN01 V0 Resolution XGA (1024 x 768) Active Area (mm) Pixel Pitch (mm) Mode 245.76 x 184.32 0.3075 TN Number of Colors 262K View Angle (H/V) 160/160 Brightness (cd/m2) Contrast Ratio Response Time (ms) (at 25C) Power Consumption (W) Interface 500 700:1 35 9.15 1ch LVDS Supply Voltage (V) 3.
DM Series Monitor 3.1.6 DM-104 LCD Specifications Table 3-5 lists the DM-104 LCD specifications. 5 Model DM-104 10.4” Size MFR/Model AUO/G104SN02 V2 Resolution SVGA (800 x 600) Active Area (mm) Pixel Pitch (mm) Mode 211.2 x 158.4 0.264 TN Number of Colors 262K View Angle (H/V) 160 / 140 Brightness (cd/m2) Contrast Ratio 400 700:1 Response Time (ms) (at 25C) 30 Power Consumption (W) 5.2 Interface 1ch LVDS Supply Voltage (V) 3.
DM Series Monitor 3.1.7 DM-84 LCD Specifications Table 3-6 lists the DM-84 LCD specifications. 5 Model DM-84 Size 8.4” MFR/Model AUO/G084SN05 V8 Resolution SVGA (800 x 600) Active Area (mm) Pixel Pitch (mm) Mode 170.4 x 127.8 0.213 TN Number of Colors 262K View Angle (H/V) 160 / 140 Brightness (cd/m2) Contrast Ratio 450 600:1 Response Time (ms) (at 25C) 30 Power Consumption (W) 4.2 Interface LVDS Supply Voltage (V) 3.
DM Series Monitor 3.1.8 DM-65 LCD Specifications Table 3-7 lists the DM-65 LCD specifications. 5 Model DM-65 Size 6.5” MFR/Model AUO/G065VN01 V2 Resolution VGA (640 x 480) Active Area (mm) Pixel Pitch (mm) Mode Number of Colors Color Saturation (NTSC%) View Angle (H/V) Brightness (cd/m2) Contrast Ratio Response Time (ms) (at 25C) 132.48 x 99.36 0.207 TN 262K 55 160/140 800 600:1 25 Power Consumption (W) 3.86 Interface LVDS Supply Voltage (V) 3.
DM Series Monitor Chapter 4 4 AD Boards Page 38
DM Series Monitor 4.1 AD Board Overview The DM series LCD monitor AD board provides a wide variety of control interfaces, receiving and managing interface signals from a CPU card through cabling. There are three AD boards used for the DM series monitors: AV-9650, AV-6650 and AV-6600. Refer to Table 1-2 for a listing of DM series monitors and their associated AD board. The 5 following sections describe each AD board in detail. 4.2 AV-9650 AD Board Overview Figure 4-1: AV-9650 AD Board Overview 4.2.
DM Series Monitor Connector Type Label Auto-dimming connector 6-pin wafer connector CN7 Backlight Inverter connector 4-pin wafer connector CN16 Debug port connector 4-pin wafer connector CN9 9-pin wafer connector CN10 LVDS connector 30-pin crimp connector CN15 Power input connector 3-pin connector CN2 Power output connector 2-pin wafer connector CN4 USB signal input connector 4-pin wafer connector CN17 Touchscreen connector 9-pin wafer connector J4 VGA connector 10-pin box head
DM Series Monitor 4.
DM Series Monitor 4.3.1 AV-6650 Peripheral Interface Connectors Table 4-3 shows a list of the peripheral interface connectors on the AV-6650 AD board.
DM Series Monitor 4.4 AV-6600 AD Board Overview The AV-6600 AD board provides a wide variety of control interfaces, receiving and managing interface signals from a CPU card through cabling. The following sections describe the AV-6600 AD board in detail. Figure 4-3: AV-6600 AD Board Overview 4.4.1 AV-6600 Peripheral Interface Connectors Table 4-5 shows a list of the peripheral interface connectors on the AV-6600 AD board.
DM Series Monitor Auto-dimming connector 6-pin wafer connector CN7 Debug connector 4-pin wafer connector CN9 External OSD and LED indication connector 9-pin wafer connector CN10 Infrared connector 6-pin wafer connector CN8 Inverter interface connector 6-pin wafer connector CN6 LVDS connector 30-pin connector CN5 Power output connector (+12 V) 2-pin wafer connector CN3 Power output connector (+5 V) 2-pin wafer connector CN4 Power input connector 3-pin connector CN2 RS-232 and USB s
DM Series Monitor Chapter 5 5 Installation Page 45
DM Series Monitor 5.1 Installation Precautions When installing the DM series LCD monitor, please follow the precautions listed below: Read the user manual: The user manual provides a complete description of the DM series LCD monitor, installation instructions and configuration options. DANGER! Disconnect Power: Power to the monitor must be disconnected when installing the DM series LCD monitor, or before any attempt is made to access the rear panel.
DM Series Monitor 5.2 Unpacking 5.2.1 Packaging When shipped, the DM series LCD monitor is wrapped in a plastic bag. Two polystyrene ends are placed on either side of the monitor. The monitor is then placed into a first (internal) cardboard box. This box is then sealed and placed into a second (external) cardboard box. The second box is also sealed. A bag containing accessory items is placed underneath the monitor, at the bottom of the internal (first) box. 5.2.
DM Series Monitor 5.2.3 Packing List All the monitors in the DM series are shipped with the following components: 1 x DM-190/170/150/121/104/84/65 series LCD monitor.
DM Series Monitor 5.3.2 Voltage Select Jumper Settings If the monitor comes with both 12V and 9~36V DC power connectors, the voltage select jumper on the integrated AD board must be configured for the DC connector that is used to power the monitor. Refer to Chapter 4 for the appropriate jumper settings of each AD 5 board. NOTE: The default voltage select jumper is configured for a 12V power source.
DM Series Monitor 5.4 Connectors Table 5-1 lists the rear panel connectors for the DM series LCD monitors.
DM Series Monitor 5.4.1 Rear Panel Connectors Overview Figure 5-1: Monitor Rear Panel Connections Figure 5-1 shows all the possible rear panel connectors for the DM series LCD monitor. 5 Refer to Table 5-1 for a list of the monitors and their corresponding connectors. The 5 following sections fully describe the rear panel connectors for the DM series LCD monitor. 5.4.2 VGA Connector Use the rear panel standard 15-pin female VGA connector to connect the monitor to the system graphics interface.
DM Series Monitor Table 5-2: VGA Connector Pinouts Figure 5-2: VGA Connector 5.4.3 DVI-D Connector Use the rear panel standard 24-pin female DVI-D connector to connect the monitor to the system graphics interface.
DM Series Monitor 5.4.4 12V Power Connector Use the rear panel +12V DC jack to connect the monitor to a power source. Figure 5-4: 12V Power Connector 5.4.5 RS-232 Touch Panel Connector Use the rear panel standard RS-232 DB-9 female touch panel connector to connect the monitor to the system graphics interface.
DM Series Monitor 5.4.6 USB Touch Panel Connector Use the rear panel standard USB touch panel connector to connect the monitor to the system graphics interface. PIN DESCRIPTION PIN DESCRIPTION 1 VCC 5 VCC 2 Data- 6 Data- 3 Data+ 7 Data+ 4 GND 8 GND Table 5-5: USB Touch Panel Connector Pinouts Figure 5-6: USB Touch Panel Connector 5.4.7 Optional DC Power Connector Use the rear panel 3-pin terminal block DC power connector to connect the monitor to a DC power source.
DM Series Monitor 5.5 Mounting the Monitor The DM series LCD monitor can be mounted in a panel, cabinet, rack, DIN rail or wall. The monitor can also be mounted on a monitor arm or stand. The mounting methods are described below. CAUTION: When mounting the monitor take care to tighten the retention screws or bolts until fully secure, but do not over tighten. Over tightening the retention screws or bolts may cause them to become stripped, rendering them useless. 5.5.
DM Series Monitor 5.5.1.1 Standard Panel Mounting The standard panel mounting procedure applies to the following DM series LCD monitors: DM-190 DM-170 DM-150 DM-121 DM-104 DM-84 To mount the DM series LCD monitor into a panel, please follow the steps below. Step 1: Select the position on the panel to mount the monitor. Step 2: Cut out a section of the panel that corresponds to the rear panel dimensions of the monitor.
DM Series Monitor Figure 5-9: DM-104 Panel Opening (Unit: mm) Figure 5-10: DM-121 Panel Opening (Unit: mm) Figure 5-11: DM-150 Panel Opening (Unit: mm) Page 57
DM Series Monitor Figure 5-12: DM-170 Panel Opening (Unit: mm) Figure 5-13: DM-190 Panel Opening (Unit: mm) Step 3: Slide the monitor through the hole until the metal frame is flush against the panel (Figure 5-14).
DM Series Monitor Figure 5-14: Insert the Monitor Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of the monitor, behind the metal frame. Refer to the mounting kit packing list for the required number of mounting clamps.
DM Series Monitor Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 5-15). 5 5.5.1.2 DM-65 Panel Mounting To mount the DM-65 monitor into a panel, follow steps one through three of the standard panel mounting procedure (Section 5.5.1.1), then continue using the steps below. 5 Step 1: Cut out a section of the panel that corresponds to the rear panel dimensions of the monitor.
DM Series Monitor Figure 5-17: DM-65 Panel Mounting Step 3: Tighten the panel retention screws that pass through the panel mounting clips until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 5-17). 5 Step 0: 5.5.2 Cabinet and Rack Installation Each model of the DM series LCD monitor has a series of holes located on the rear of the front panel for mounting the monitor to a rack or cabinet. NOTE: 1.
DM Series Monitor 5.5.2.1 Standard Cabinet and Rack Installation The standard cabinet/rack mounting procedure applies to the following DM series LCD monitors: DM-170 DM-150 DM-121 DM-104 To mount the DM series LCD monitor into a cabinet/rack, please follow the steps below. Step 1: The back of the metal frame surrounding the DM series LCD monitor has several retention screw holes for a cabinet/rack installation bracket.
DM Series Monitor Figure 5-18: Secure the Cabinet/Rack Bracket Step 5: Slide the monitor with the attached cabinet/rack bracket into a rack or cabinet (Figure 5-19).
DM Series Monitor Figure 5-19: Install into a Cabinet/Rack Step 6: Once the monitor with the attached cabinet/rack has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 5-19). 5 5.5.2.2 DM-190 Cabinet and Rack Installation To mount the DM-190 monitor into a cabinet/rack, please follow the steps below. Step 1: Insert and tighten the supplied mounting nuts and bolts to the rack for the rack mounting bracket.
DM Series Monitor Figure 5-20: Rack Mounting Nuts and Bolts Installation (DM-190) Step 2: Secure the rack mounting bracket to two sides of the monitor using the supplied retention screws. Each bracket requires four screws.
DM Series Monitor Step 3: Carefully insert the slotted holes of the brackets on the monitor through the bolts on the rack and gently pull the monitor downwards until the bolts rests securely in the slotted holes. (See Figure 5-22). Ensure that all six of the bolts fit snuggly 5 into their respective slotted holes. Figure 5-22: Rack Mounting (DM-190) 5.5.2.3 DM-84 and DM-65 Cabinet and Rack Installation Use the standard panel mounting procedure (Section 5.5.1.
DM Series Monitor Step 1: Attach the DIN rail mounting bracket to the rear of the monitor. Secure the bracket to the monitor with the supplied retention screws (Figure 5-23). 5 Figure 5-23: DIN Rail Mounting Bracket Step 2: Make sure the inserted screw in the center of the bracket is at the lowest position of the elongated hole (Figure 5-24).
DM Series Monitor Figure 5-25: Mounting the DIN RAIL Step 4: Secure the DIN rail to the mounting bracket by turning the top screw clockwise. This draws the lower clamp up and secures the monitor to the DIN rail (Figure 5 5-26).
DM Series Monitor 5.5.4 Wall Mounting CAUTION: Due to safety concerns, it is highly recommended to use the VESA mounting kits provided by IEI for wall, stand and arm mounting. If the VESA mounting kit is purchased separately, please make sure the mounting kit is UL-listed. Each model of the DM series LCD monitor has four holes located on the rear panel for mounting the monitor to a wall. To mount the DM series LCD monitor onto a wall, please follow the steps below.
DM Series Monitor Step 6: Insert the four monitor mounting screws (M4 screws) provided in the wall mounting kit into the four screw holes on the real panel of the monitor and tighten until the screw shank is secured against the rear panel (Figure 5-28). 5 Figure 5-28: Monitor Support Screws Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket.
DM Series Monitor NOTE: In the diagram below the bracket is already installed on the wall. Figure 5-29: Wall Mounting the Monitor 5.5.5 Monitor Stand Installation The DM series LCD monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-30).
DM Series Monitor Figure 5-30: VESA Mounting Holes The monitor stand mounting plate has a matching VESA hole pattern. To mount the DM series LCD monitor onto a stand, please follow the steps below. Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the monitor stand mounting plate. Step 2: Secure the monitor to the stand with the supplied retention screws (Figure 5 5-31).
DM Series Monitor 5.5.6 Monitor Arm Installation The DM series LCD monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-30). The monitor arm mounting plate has a matching 5 VESA hole pattern. To mount the DM series LCD monitor onto a monitor arm, please follow the steps below.
DM Series Monitor Chapter 6 6 On-Screen-Display (OSD) Controls Page 74
DM Series Monitor 6.1 User Mode OSD Structure 6.1.1 OSD Buttons There are several on-screen-display (OSD) control buttons oriented either vertically along the right hand side or horizontally along the bottom of the monitor front panel. Refer to Section 2.2 for availability and orientation of the OSD controls on specific DM series 5 monitors. Figure 6-1 shows a typical arrangement of OSD controls for all models of the DM series 5 LCD monitor except the DM-65.
DM Series Monitor Figure 6-2 shows the OSD controls for the DM-65. 5 Figure 6-2: DM-65 OSD Control Buttons 6.1.2 OSD Menu Structure Table 6-1 shows the OSD menu structure for all models of the SRM series LCD monitor. 5 Level 0 Level 1 Value Main Display Features Menu Brightness 0 to 100 Contrast 0 to 100 Clock 0 to 100 Phase 0 to 100 H. Position 0 to 100 V.
DM Series Monitor OSD Menu Exit Menu OSD Time Out 0 to 60 sec OSD Position 1 to 5 OSD Transparency 20, 40, 60, 80, 100 Factory Reset Select Auto Adjust Select Auto Color Select Gamma Off, On Exit Select Table 6-1: OSD Menus Page 77
DM Series Monitor 6.2 Using the OSD OSD menu options are described below. 6.2.1 Main Display Features Main display features are shown in Figure 6-3. Figure 6-3: Main Display Features The brightness option adjusts the brightness of screen. This function Brightness adjusts the offset value of ADC. Setting this value too high or too low will affect the quality of image. When the auto- dimming function is turned on, the brightness control is not effective.
DM Series Monitor 6.2.2 Color Color options are shown in Figure 6-4. Figure 6-4: Color Options The Color menu fine-tunes the palette of color hues for the LCD. 6500k NTSC standard Kelvin 7500k NTSC standard Kelvin 9300k NTSC standard Kelvin User This item allows fine-tuning the balance among Red, Green, and Blue color hues if images look garish or unrealistic.
DM Series Monitor 6.2.3 OSD Configurations The OSD configurations are shown in Figure 6-5. Figure 6-5: OSD Configurations Menu OSD Configurations are described below. OSD Time Out Determines how many seconds the OSD screen stays on screen before it disappears when OSD is left unattended. Adjusts the OSD position on the screen. Position 1 is in the upper left OSD Position of the screen, position 2 in the upper right and position 3 in the center.
DM Series Monitor Chapter 7 7 Software Drivers Page 81
DM Series Monitor 7.1 Introduction The touch panel controller enables analog resistive touch panels for four-wire, five-wire & eight-wire models. The controller directly communicates with the PC system through the touch panel communications interface. The controller design is superior in sensitivity, accuracy, and friendly operation. The touch panel driver emulates the left mouse button and the right mouse button functions.
DM Series Monitor USB Interface: If the touch screen interface connection is a USB connection, connect the USB connector on the single board computer to the external USB port connector of the DM Series monitor. 7.3 Touch Panel Driver Installation WARNING: Before the touch screen driver is installed, make sure the system is connected to the monitor with a USB cable or an RS-232 null cable. Also, make sure the VGA connector on the system is connected to the VGA connector on the bottom of the monitor.
DM Series Monitor Step 4: Double click the setup icon in Figure 7-1. Step 5: The Welcome screen in Figure 7-2 appears. Figure 7-2: Welcome Screen Step 6: Click Next to continue. Step 7: The license agreement in Figure 7-3 appears. Accept the terms of the agreement by clicking I Agree.
DM Series Monitor Step 8: The installation destination screen appears. See Figure 7-4. Click Install. Figure 7-4: Initiate Install Step 9: The installation of the program begins. See Figure 7-5. Figure 7-5: Installation Starts Step 10: When the installation is complete, the complete screen appears. See Figure 7-6. To complete the installation process click Finish.
DM Series Monitor Figure 7-6: Finish Installation 7.4 Change the Touch Screen Interface If the touch screen interface must be changed from an RS-232 interface to a USB interface or, from a USB interface to an RS-232 interface, the following steps must be followed. Step 1: Uninstall the touch screen driver Step 2: Remove the interface cable i.e. remove the RS-232 cable or the USB cable Step 3: Install the new cable i.e. install the USB cable or the RS-232 cable.
DM Series Monitor Step 3: Locate the PenMount Monitor icon in the bottom left corner of the screen. Figure 7-7: PenMount Monitor Icon Step 4: Click the icon. A pop up menu appears. See Figure 7-8. Figure 7-8: PenMount Monitor Popup Menu Step 5: Click Control Panel in the pop up menu shown in Figure 7-8. Step 6: The configuration screen in Figure 7-9 appears.
DM Series Monitor Step 7: Double click the PenMount 6000 icon as shown in Figure 7-9. Step 8: The calibration initiation screen in Figure 7-10 appears. Step 9: Select the Standard Calibration button as shown in Figure 7-10. Figure 7-10: Calibration Initiation Screen Step 10: The calibration screen in is shown. See Figure 7-11. Figure 7-11: Calibration Screen Step 11: Follow the instructions. The user is asked touch the screen at five specified points after which the screen is calibrated.
DM Series Monitor Chapter 8 8 Gasket Replacement Page 89
DM Series Monitor 8.1 Gasket Replacement A gasket used for a long time may gradually lose its ability to protect the monitor from fluids and vapors; scratches or dirt may also accumulate. It is recommended that the gasket be replaced yearly. NOTE: If the monitor is mounted vertically, first remove it and place it on a flat, level surface with the display screen facing down before changing the gasket. Step 1: Remove the old gasket from the sides of the monitor. Step 2: Attach the new gasket to the monitor.
DM Series Monitor Appendix A A Safety Precautions Page 91
DM Series Monitor WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the DM Series. A.1 Safety Precautions Please follow the safety precautions outlined in the sections that follow: A.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times. Follow the electrostatic precautions outlined below whenever the DM Series is opened.
DM Series Monitor A.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the DM Series may result in permanent damage to the DM Series and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the DM Series. Dry climates are especially susceptible to ESD.
DM Series Monitor The interior of the DM Series does not require cleaning. Keep fluids away from the DM Series interior. Be cautious of all small removable components when vacuuming the DM Series. Turn the DM Series off before cleaning the DM Series. Never drop any objects or liquids through the openings of the DM Series. Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the DM Series.
DM Series Monitor Appendix B B Certifications Page 95
DM Series Monitor B.1 RoHS Compliant All models in the DM LCD monitor series comply with the Restriction of Hazardous Materials (RoHS) Directive. This means that all components used to build the industrial workstations and the workstation itself are RoHS compliant.
DM Series Monitor Appendix C C smartOSD Page 97
DM Series Monitor C.1 IEI smartOSD Quick Installation Guide IEI smartOSD is a proprietary On-Screen-Display (OSD) software solution from IEI that enables easy, remote monitor setting adjustments in a Windows environment. IEI smartOSD delivers excellent performance and provides more flexibility than the typical OSD hardware solutions when adjusting a monitor.
DM Series Monitor Figure 8-2: smartOSD Installer Step 2: Click “Smart OSD” in Figure 8-2. 5 Step 3: The welcome screen shown in Figure 8-3 appears. 5 Figure 8-3: smartOSD Welcome Screen Step 4: Click Next to continue. Step 5: The Folder Select screen in Figure 8-4 appears.
DM Series Monitor Figure 8-4: smartOSD Folder Select Screen Step 6: Select the installation folder in Figure 8-4 shown above. 6 Step 7: Click Next to continue. Step 8: The screen in Figure 8-5 appears. 6 Figure 8-5: smartOSD Confirm Installation Step 9: Confirm the installation by clicking Next in the screen above. Step 10: The program starts to install and the progress bar shown in Figure 8-6 appears.
DM Series Monitor Figure 8-6: smartOSD Installation Progress Step 11: When the installation is complete the “Complete Installation” screen in Figure 6 8-7 appears. Figure 8-7: smartOSD Installation Complete Step 12: Click Close in the screen above. Step 13: After quick setup is complete, the IEI smartOSD wizard logo appears on the desktop as shown in the screen below. Step 14: To access the smartOSD, click the smartOSD wizard logo.
DM Series Monitor C.4 Software Illustration The table below shows the smartOSD menu structure for all IEI LCD monitors. NOTE: To update the display setting status immediately, push the refresh button on every page To turn the system on, press ALT + P. Item Elements Management Save/Load File Power Management EDID EDID contains basic information about the monitor and its capabilities.
DM Series Monitor Display Auto Adjust Phase Clock Color Auto Color User Red Gain User Green Gain User Blue Gain Color Temperature (5000k and 4200k disabled in the DM Series) Gamma PIP PIP (disabled in the DM Series) PIP Source Input (disabled in the DM Series) PIP Size (disabled in the DM Series) System Monitor Power Control Auto Brightness (disabled in the DM Series) Main Source Input (S-Video and CVBS disabled) Volume (disabled in the DM Series) Factory Presets/OSD Lock/OSD Unlock Mute (disabled in
DM Series Monitor C.4.
DM Series Monitor C.4.
DM Series Monitor C.4.
DM Series Monitor C.4.
DM Series Monitor C.4.
DM Series Monitor C.4.6 PIP Page NOTE: The functions in the PIP page are only available in the MDM Series and AFOLUX Series monitors.
DM Series Monitor C.4.
DM Series Monitor C.4.
DM Series Monitor C.5 smartOSD FAQ For troubleshooting, please see the steps below: C.5.1 Windows 2000 Installation Failure Installation fails under Windows 2000 and shows the following image: Figure C-9: DLL Missing Solution: Download and install service pack Windows Installer 3.1 C.5.
DM Series Monitor Solution: Install SmartOSD.exe as the administrator authority Figure C-11: Install as Administrator C.5.3 Model Failure The Model Fail error message shown below appears. Figure C-12: Firmware Incompatibility Solution: SmartOSD only supports firmware version 2.0 and following versions.
DM Series Monitor C.5.4 DCC Port Failure The DDC port fail error message shown below appears. Figure C-13: DCC Port Failure Solutions: Check VGA or DVI cable Check an IEI monitor is being used Make sure the version is version 2.3 for the AFOLUX/MDM series and version 1.5 for the DM/ISDM/TDM/SRM/LCD-KIT series that have the SmartOSD functions Check if the OSD control status is busy. A busy signal may cause the signal message for a short time.
