Manual

ManualsBrandsIEI Integration ManualsComputersAFL2-10A-N28

AFL2-10A-N28 Panel PC

Page I

IEI Technology Corp.

User Manual

AFL2-10A-N28 Series

MODEL:

Flat Bezel Panel PC with Intel®

tom™ N2800 Dual-Core CPU

Touchscreen, Wi-Fi, Bluetooth, USB, GbE LAN, RS-232/422/485,

2-Megapixel Camera, HD Audio and RoHS

Rev. 1.00 - 26 February, 2013

User Manual

Summary of content (203 pages)

PAGE 1
AFL2-10A-N28 Panel PC IEI Technology Corp. MODEL: AFL2-10A-N28 Series Flat Bezel Panel PC with Intel® Atom™ N2800 Dual-Core CPU Touchscreen, Wi-Fi, Bluetooth, USB, GbE LAN, RS-232/422/485, 2-Megapixel Camera, HD Audio and RoHS User Manual Page I Rev. 1.
PAGE 2
AFL2-10A-N28 Panel PC Revision Date Version Changes 26 February, 2013 1.
PAGE 3
AFL2-10A-N28 Panel PC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
AFL2-10A-N28 Panel PC Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.1.1 Features ............................................................................................................. 3 1.2 EXTERNAL OVERVIEW ......................................................................
PAGE 5
AFL2-10A-N28 Panel PC 3.11 MOUNTING THE SYSTEM ........................................................................................ 26 3.11.1 Wall Mounting ................................................................................................ 27 3.11.2 Panel Mounting .............................................................................................. 30 3.11.3 Cabinet and Rack Installation........................................................................ 31 3.11.
PAGE 6
AFL2-10A-N28 Panel PC 4.3.7 H/W Monitor .................................................................................................... 60 4.3.8 Serial Port Console Redirection ...................................................................... 60 4.4 IEI FEATURE ............................................................................................................. 62 4.5 CHIPSET ...................................................................................................................
PAGE 7
AFL2-10A-N28 Panel PC 6.6 REINSTALLING THE COVERS ....................................................................................112 7 INTERFACE CONNECTORS ..................................................................................113 7.1 PERIPHERAL INTERFACE CONNECTORS....................................................................114 7.2 INTERNAL PERIPHERAL CONNECTORS .....................................................................115 7.2.1 Audio Connector (AUDIO1) ...................
PAGE 8
AFL2-10A-N28 Panel PC 7.3.4 RS-422/485 RJ-45 Serial Port (COM2)......................................................... 127 7.3.5 RS-232 RJ-45 Serial Ports (COM3) .............................................................. 127 7.3.6 USB 2.0 Connectors (USB1).......................................................................... 128 7.3.7 USB 3.0 Connectors (USB3_1)...................................................................... 128 7.3.8 DisplayPort Connector (DISPLAY_PORT1) ...................
PAGE 9
AFL2-10A-N28 Panel PC C.6.1 Configure DHCP Server Settings.................................................................. 170 C.6.2 Configure TFTP Settings ............................................................................... 171 C.6.3 Configure One Key Recovery Server Settings ............................................... 172 C.6.4 Start the DHCP, TFTP and HTTP ................................................................. 173 C.6.5 Create Shared Directory.................................
PAGE 10
AFL2-10A-N28 Panel PC List of Figures Figure 1-1: AFL2-10A-N28 Flat Bezel Panel PC ...........................................................................2 Figure 1-2: Front View ....................................................................................................................3 Figure 1-3: LED Indicators.............................................................................................................4 Figure 1-4: Function Keys ...............................................
PAGE 11
AFL2-10A-N28 Panel PC Figure 3-24: Secure System to V-Stand .....................................................................................37 Figure 3-25: Secure V-Stand to Mounting Area.........................................................................38 Figure 3-26: Audio Connector .....................................................................................................39 Figure 3-27: DisplayPort Connection ...........................................................................
PAGE 12
AFL2-10A-N28 Panel PC Figure 5-27: LAN Driver Ready to Install Screen.......................................................................89 Figure 5-28: LAN Driver Setup Status Screen ...........................................................................89 Figure 5-29: LAN Driver Installation Complete..........................................................................90 Figure 5-30: USB 3.0 Driver Welcome Screen ...........................................................................
PAGE 13
AFL2-10A-N28 Panel PC Figure C-4: Command Prompt ................................................................................................. 145 Figure C-5: Partition Creation Commands.............................................................................. 146 Figure C-6: Launching the Recovery Tool .............................................................................. 148 Figure C-7: Manual Recovery Environment for Windows .....................................................
PAGE 14
AFL2-10A-N28 Panel PC Figure C-39: Restore Backup ................................................................................................... 167 Figure C-40: Restore System Backup Complete Window ..................................................... 167 Figure C-41: Symantec Ghost Window ................................................................................... 168 Figure C-42: Disable Automatically Restart............................................................................
PAGE 15
AFL2-10A-N28 Panel PC List of Tables Table 1-1: LED Indicators ..............................................................................................................5 Table 1-2: Function Key Descriptions ..........................................................................................6 Table 1-3: System Specifications................................................................................................10 Table 3-1: DB-9 Connector Pinout ...........................................
PAGE 16
AFL2-10A-N28 Panel PC Table 7-27: Webcam Microphone Connector (WEBCAM_DMIC1) Pinouts.......................... 125 Table 7-28: Rear Panel Connectors ......................................................................................... 125 Table 7-29: Ethernet Connector (JP6) Pinouts ....................................................................... 126 Table 7-30: Power Connector (DC_IN1) Pinouts ....................................................................
PAGE 17
AFL2-10A-N28 List of BIOS Menus BIOS Menu 1: Main .......................................................................................................................48 BIOS Menu 2: Advanced ..............................................................................................................50 BIOS Menu 3: ACPI Configuration ..............................................................................................50 BIOS Menu 4: RTC Wake Settings ............................................
PAGE 18
AFL2-10A-N28 Panel PC Chapter 1 1 Introduction Page 1
PAGE 19
AFL2-10A-N28 Panel PC 1.1 Overview Figure 1-1: AFL2-10A-N28 Flat Bezel Panel PC The AFL2-10A-N28 is an Intel® Atom™ N2800 dual-core processor powered flat bezel panel PC with a rich variety of functions and peripherals. The AFL2-10A-N28 is designed for easy and simplified integration into kiosk and point-of-sales (POS) applications. An Intel® NM10 chipset ensures optimal memory, graphics, and peripheral I/O support. The system comes with two 2.
PAGE 20
AFL2-10A-N28 Panel PC 1.1.1 Features The AFL2-10A-N28 features are listed below: Flat-bezel LCD with LED backlight 1.86 GHz Intel® Atom™ N2800 dual-core processor One 204-pin DDR3 SO-DIMM slot (system max. 4 GB) preinstalled with 2 GB memory 5-wire resistive type touchscreen Wi-Fi 802.11b/g/n 2T2R high speed wireless Built-in 2-megapixel camera with AF, AE and AWB capabilities Built-in two 1.
PAGE 21
AFL2-10A-N28 Panel PC 1.2.1.1 LED Indicators There are several LED indicators located along the bottom of the LCD screen (Figure 1-3). Figure 1-3: LED Indicators The descriptions of each LED indicator are listed below. LED Indicator Description Power Off: power cord not attached or power supply failure Blinking amber: the system is connected to a power source and is ready to be turned on. Solid blue: the system is turned on. Power on/off by the hot keys.
PAGE 22
AFL2-10A-N28 Panel PC Bluetooth On: the Bluetooth module is enabled. Off: the Bluetooth module is disabled. Controlled by the BIOS. See Section 4.5.2 Microphone On: the digital microphone is enabled Off: the digital microphone is disabled. Controlled by the BIOS. See Section 4.5.2 Audio Mute On (solid red): the audio is turned off Off: the audio is turned on Controlled by the hot keys. See Table 1-3 Mini USB On: the Mini USB 2.0 module is enabled Off: the Mini USB 2.0 module is disabled.
PAGE 23
AFL2-10A-N28 Panel PC 1.2.1.2 Function Keys The function keys are located under the bottom right hand corner of the LCD screen (Figure 1-4). Figure 1-4: Function Keys The function keys are described in Table 1-3: Key Combination Function Key Description Fn Function key.
PAGE 24
AFL2-10A-N28 Panel PC 1.2.2 Rear Panel The rear panel provides access to retention screw holes that support VESA mounting. The HDD bay is protected by the HDD cover. Refer to Figure 1-5. Figure 1-5: Rear View 1.2.
PAGE 25
AFL2-10A-N28 Panel PC 1 x RS-232 RJ-45 connector (COM3) 1 x RS-422/485 RJ-45 connector 2 x USB 2.0 connectors 2 x USB 3.0 connectors Figure 1-6: Bottom Panel 1.2.4 Left Side Panel The left side panel of the AFL2-10A-N28 has a temperature sensor (Figure 1-7).
PAGE 26
AFL2-10A-N28 Panel PC 1.3 Internal Overview The AFL2-10A-N28 has the following components installed internally: 1 x Motherboard 1 x 2.0 GB 1066 MHz DDR3 SO-DIMM 1 x 802.11b/g/n wireless LAN module 1.4 System Specifications The technical specifications for the AFL2-10A-N28 systems are listed in Table 1-4. Specification AFL2-10A-N28 LCD Size 10.4" Max. Resolution 800 (W) x 600 (H) Brightness (cd/m2) 400 Contrast Ratio 700:1 LCD Color 262K/16.2M Pixel Pitch (H x V) (mm) 0.264 (H) x 0.
PAGE 27
AFL2-10A-N28 Panel PC OSD Function LCD on/off, brightness up/down, volume up/down, Hot Key Construction Material PC+ABS plastic front frame Mounting VESA 75 mm x 75 mm (Panel, Wall, Rack, Stand or Arm) Front Panel Color Black Weight (N/G) 2.98 kg / 4.5 kg Dimensions (W x H x D) 282.5 mm x 242.7 mm x 51.
PAGE 28
AFL2-10A-N28 Panel PC 1.5 Dimensions The AFL2-10A-N28 dimensions are shown below. Width: 282.5 mm Height: 242.7 mm Depth: 51.
PAGE 29
AFL2-10A-N28 Panel PC Chapter 2 2 Unpacking Page 12
PAGE 30
AFL2-10A-N28 Panel PC 2.1 Unpacking To unpack the flat bezel panel PC, follow the steps below: WARNING! The front side LCD screen has a protective plastic cover stuck to the screen. Only remove the plastic cover after the flat bezel panel PC has been properly installed. This ensures the screen is protected during the installation process. Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the external (second) box. Step 2: Open the external (second) box.
PAGE 31
AFL2-10A-N28 Panel PC Quantity Item Standard 1 AFL2-10A-N28 panel PC 1 Power adapter (P/N: 63040-010060-030-RS) 1 Power cord (P/N: 32702-000401-100-RS) 1 Power transfer cord (P/N: 32702-000300-100-RS) 1 RJ-45 to DB-9 COM Port Cable (P/N: 32005-000200-200-RS) 1 Pen for resistive touchscreen (P/N: 43125-0002C0-00-RS) 4 M3*4 flat head screw pack for HDD installation (P/N: 44013-030041-RS) 4 M4*6 pan head screw pack for VESA mount (P/N: 44403-040061-RS) 1 Utility CD 1 One Key Recovery CD (P/N
PAGE 32
AFL2-10A-N28 Panel PC Optional Wall mounting kit (P/N: AFLWK-12) Panel mounting kit (P/N: AFL2PK-10A) Rack mounting kit (P/N: AFL2RK-10A) Stand (P/N: STAND-C12/ STAND-B19) Stand (P/N: VSTAND-A10) Hybrid card reader (P/N: AFL2P-12AMSI-U-R10) Magnetic stripe reader (P/N: AFL2P-12AMSR-U-R10) Bluetooth module kit (P/N: AFL2-BT-KIT01-R11) OS: Win CE 6.
PAGE 33
AFL2-10A-N28 Panel PC OS: Win XPE (CD-ROM) (P/N: AFL2-W10A-CV-XPE-R10) OS: Linux (CD-ROM) (P/N: AFL2-W10A-CV-LNX-R10) OS: Win 7 Embedded (DVD-ROM) (P/N: AFL2-W10A-CV-WES7P-R10 or AFL2-W10A-CV-WES7E-R10) If any of these items are missing or damaged, contact the distributor or sales representative immediately.
PAGE 34
AFL2-10A-N28 Panel PC Chapter 3 3 Installation Page 17
PAGE 35
AFL2-10A-N28 Panel PC 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the maintenance of the AFL2-10A-N28 may result in permanent damage to the AFL2-10A-N28 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the AFL2-10A-N28. Dry climates are especially susceptible to ESD.
PAGE 36
AFL2-10A-N28 Panel PC Anti-static Discharge: If a user open the rear panel of the flat bezel panel PC, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear an anti-static wristband. 3.3 Installation and Configuration Steps The following installation steps must be followed. Step 1: Unpack the flat bezel panel PC. Step 2: Install the HDD. Step 3: Install the RFID reader. (optional) Step 4: Configure the system.
PAGE 37
AFL2-10A-N28 Panel PC Figure 3-1: HDD Cover Retention Screws Step 2: Remove the HDD cover from the device. Step 3: Loosen the captive screw to release the HDD bracket from the chassis. Slide the HDD bracket out of the device as shown (Figure 3-2). Figure 3-2: HDD Bracket Removal Step 4: Insert an HDD into the bracket as shown in Figure 3-3.
PAGE 38
AFL2-10A-N28 Panel PC Figure 3-3: Inserting the HDD Step 5: Secure the HDD to the bracket using four (4) M3*4 retention screws (two screws on each side) (Figure 3-4). Figure 3-4: Securing the HDD Step 6: Slide the HDD module back into the device. Step 7: Tighten the captive screw. Step 8: Replace the HDD cover and secure it using two (2) retention screws.
PAGE 39
AFL2-10A-N28 Panel PC 3.5 RFID Reader Installation (Optional) An optional RFID reader can be installed in the AFL2-10A-N28. To install the RFID reader, follow the instructions below. Step 1: Remove a total of eleven (11) retention screws from the back cover (Figure 3-5). Figure 3-5: Back Cover Retention Screws Step 2: Remove the five (5) retention screws securing the internal cover to the chassis (Figure 3-6).
PAGE 40
AFL2-10A-N28 Panel PC Step 3: Using two retention screws to install the RFID reader module in the location shown in Figure 3-7. Figure 3-7: RFID Reader Module Installation Step 4: Connect the RFID module to the RFID connector on the main board (Figure 3-8). The RFID connector pinouts are listed in Section 7.2.17. Step 5: Place the RFID antenna on the location shown in Figure 3-8. Connect the RFID antenna to the RFID antenna connector on the RFID module.
PAGE 41
AFL2-10A-N28 Panel PC Step 6: Replace the internal cover and back cover using previously removed retention screws. Step 0: 3.6 AT/ATX Mode Selection AT or ATX power mode can be used on the AFL2-10A-N28. The selection is made through an AT/ATX switch located on the bottom panel. To select AT mode or ATX mode, follow the steps below. Step 1: Locate the AT/ATX switch on the bottom panel (Figure 3-9). Figure 3-9: AT/ATX Switch Location Step 2: Adjust the AT/ATX switch. Step 0: 3.6.
PAGE 42
AFL2-10A-N28 Panel PC broadcasting time for each panel PC can be set individually and controlled remotely. Other possible application includes Security surveillance Point-of-Sale (POS) Advertising terminal 3.7 Clear CMOS If the AFL2-10A-N28 fails to boot due to improper BIOS settings, the clear CMOS switch clears the CMOS data and resets the system BIOS information.
PAGE 43
AFL2-10A-N28 Panel PC Step 2: Press the reset button. Step 0: 3.9 Powering On the System To power on the system, follow the steps below: Step 1: Locate the Function and Brightness Up function keys. See Section 1.2.1.2. Step 2: Hold down the Function and Brightness Up buttons for six seconds to power on the system. Step 0: 3.10 Powering Off the System To power off the system, follow the steps below: Step 1: Locate the Function and Brightness Up function keys. See Section 1.2.1.2.
PAGE 44
AFL2-10A-N28 Panel PC V-Stand mounting The five mounting methods are described below. 3.11.1 Wall Mounting To mount the flat bezel panel PC onto the wall, please follow the steps below. Step 1: Select the location on the wall for the wall-mounting bracket. Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall. Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention screws.
PAGE 45
AFL2-10A-N28 Panel PC Step 6: Insert the four monitor mounting screws provided in the wall mount kit into the four screw holes on the real panel of the flat bezel panel PC and tighten until the screw shank is secured against the rear panel (Figure 3-13). WARNING: Please use the M4 screws provided in the wall mount kit for the rear panel. If the screw is missing, the thread depth of the replacement screw should be not more than 4 mm.
PAGE 46
AFL2-10A-N28 Panel PC Figure 3-13: Chassis Support Screws Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting bracket. (Figure 3-14).
PAGE 47
AFL2-10A-N28 Panel PC 3.11.2 Panel Mounting To mount the AFL2-10A-N28 flat bezel panel PC into a panel, please follow the steps below. Step 1: Select the position on the panel to mount the flat bezel panel PC. Step 2: Cut out a section corresponding to the size shown below. The size must be smaller then the outer edge. Figure 3-15: Cutout Dimensions Step 3: Slide the flat bezel panel PC through the hole until the frame is flush against the panel.
PAGE 48
AFL2-10A-N28 Panel PC Step 7: Tighten the screws that pass through the panel mounting clamps until the plastic caps at the front of all the screws are firmly secured to the panel. Step 8: Install the covers into the panel mounting bracket. Each mounting bracket includes two side covers and one top cover (Figure 3-16 p). Figure 3-16: Tighten the Panel Mounting Clamp Screws 3.11.3 Cabinet and Rack Installation The AFL2-10A-N28 flat bezel panel PC can be installed into a cabinet or rack.
PAGE 49
AFL2-10A-N28 Panel PC NOTE: When purchasing the cabinet/rack installation bracket, make sure it is compatible with both the AFL2-10A-N28 flat bezel panel PC and the rack/cabinet into which the AFL2-10A-N28 is installed. Step 1: Slide the rear chassis of the AFL2-10A-N28 flat bezel panel PC through the rack/cabinet bracket until the frame is flush against the front of the bracket (Figure 3-17).
PAGE 50
AFL2-10A-N28 Panel PC Step 6: Install the covers into the rack mounting bracket. Each mounting bracket includes two side covers and one top cover (Figure 3-18 p). Figure 3-18: Secure the Rack/Cabinet Bracket Step 7: Slide the flat bezel panel PC with the attached rack/cabinet bracket into a rack or cabinet (Figure 3-19).
PAGE 51
AFL2-10A-N28 Panel PC Step 8: Once the flat bezel panel PC with the attached rack/cabinet bracket has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 3-19). 3.11.4 Arm Mounting The AFL2-10A-N28 is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 75 mm interface pad. To mount the AFL2-10A-N28 on an arm, please follow the steps below.
PAGE 52
AFL2-10A-N28 Panel PC Figure 3-20: Arm Mounting Retention Screw Holes Step 4: Secure the AFL2-10A-N28 to the interface pad by inserting four retention screws through the mounting arm interface pad and into the AFL2-10A-N28.
PAGE 53
AFL2-10A-N28 Panel PC 3.11.5 Stand Mounting To mount the AFL2-10A-N28 using the stand mounting kit, please follow the steps below. Step 1: Locate the screw holes on the rear of the AFL2-10A-N28. This is where the bracket will be attached. Step 2: Align the bracket with the screw holes. Step 3: To secure the bracket to the AFL2-10A-N28 insert the retention screws into the screw holes and tighten them.Step0: Figure 3-22: Stand Mounting (Stand-A/Bxx) 3.11.
PAGE 54
AFL2-10A-N28 Panel PC Figure 3-23: Drill Pilot Holes for V-Stand Step 2: Align the screw holes on the V-Stand with the VESA mount screw holes on the system rear panel. Step 3: Insert the four VESA mount screws into the four screw holes on the system rear panel. Adjust the V-Stand to a proper position. Step 4: Tighten until the screw shank is secured against the rear panel.
PAGE 55
AFL2-10A-N28 Panel PC Step 5: Align the V-Stand screw holes with the pilot holes on the mounting area. Mount the V-Stand by inserting the retention screws into the four pilot holes and tightening them. Step 6: Adjust the V-Stand to have a best viewing angle to operate the system.Step0: Figure 3-25: Secure V-Stand to Mounting Area 3.12 External Peripheral Device Connection The following external peripheral devices can be connected to the external peripheral interface connectors.
PAGE 56
AFL2-10A-N28 Panel PC 3.12.1 Audio Connection The audio jack on the external audio connector enables the AFL2-10A-N28 to be connected to a stereo sound setup. To install the audio devices, follow the steps below. Step 1: Identify the audio plugs. The plugs on your home theater system or speakers may not match the colors on the rear panel. If audio plugs are plugged into the wrong jacks, sound quality will be very bad. Step 2: Plug the audio plug into the audio jack. Plug the audio plug into the audio jack.
PAGE 57
AFL2-10A-N28 Panel PC Step 1: Locate the DisplayPort connector. The location is shown in Chapter 3. Step 2: Align the connector. Align the DisplayPort connector with the DisplayPort port. Make sure the orientation of the connector is correct. Figure 3-27: DisplayPort Connection Step 3: Insert the DisplayPort connector. Gently insert the DisplayPort connector. The connector should engage with a gentle push.
PAGE 58
AFL2-10A-N28 Panel PC Figure 3-28: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the external interface. 3.12.4 Serial Device Connection There are two external RS-232 connectors (one by DB-9 and one by RJ-45) and one RS-422/485 RJ-45 connector for serial device connection. Follow the steps below to connect a serial device to the AFL2-10A-N28. 3.12.4.
PAGE 59
AFL2-10A-N28 Panel PC Figure 3-29: DB-9 Serial Port Connector Step 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. 3.12.4.2 RJ-45 Serial Port Connection Follow the steps below to connect a serial device to the RJ-45 serial port connector of the AFL2-10A-N28 panel PC. Step 1: Locate the RJ-45 serial port. The location of the RJ-45 serial port is shown in Chapter 1.
PAGE 60
AFL2-10A-N28 Panel PC Figure 3-30: RJ-45 Serial Port Connector Step 4: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. The DB-9 connector pinouts are listed below. Figure 3-31: DB-9 Connector Pinout Locations PIN NO.
PAGE 61
AFL2-10A-N28 Panel PC 3.12.5 USB Device Connection NOTE: User must install the USB 3.0 driver before connecting a USB device to the system or else the system may not recognize the connected device. There are two USB 2.0 connectors and two USB 3.0 connectors on the AFL2-10A-N28. To connect a USB device, please follow the instructions below. Step 1: Locate the USB connectors. The locations of the USB connectors are shown in Chapter 1. Step 2: Align the connectors.
PAGE 62
AFL2-10A-N28 Panel PC Chapter 4 4 BIOS Setup Page 45
PAGE 63
AFL2-10A-N28 Panel PC 4.1 Introduction A licensed copy of the BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed. 4.1.1 Starting Setup The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DEL or F2 key as soon as the system is turned on or 2.
PAGE 64
AFL2-10A-N28 Panel PC F2 key Load previous values. F3 key Load optimized defaults F4 key Save changes and Exit BIOS Esc key Main Menu – Quit and do not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu Table 6-1: BIOS Navigation Keys 4.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears.
PAGE 65
AFL2-10A-N28 Panel PC 4.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. 8 The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliency Project Version Build Date and Time American Megatrends 4.6.5.3 0.16 UEFI 2.3; PI 1.2 SE25AR12.ROM 11/01/2012 14:50:49 Set the Date.
PAGE 66
AFL2-10A-N28 Panel PC Î iWDD Version The iWDD Version displays the current iWDD version. The fields in iWDD Version cannot be changed. Î System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. Î System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 4.
PAGE 67
AFL2-10A-N28 Panel PC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit > > > > > > > > > ACPI Settings RTC Wake Settings CPU Configuration SATA Configuration USB Configuration F81866 Super IO Configuration H/M Monitor Serial Port Console Redirection iEi Feature System ACPI Parameters. ---------------------- ÅÆ: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.
PAGE 68
AFL2-10A-N28 Panel PC Î ACPI Sleep State [S1 (CPU Stop Clock)] Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used. Î S1 (CPU Stop DEFAULT The system enters S1 (POS) sleep state. The system appears off. The CPU is stopped; RAM is Clock) refreshed; the system is running in a low power mode. Î S3 (Suspend The caches are flushed and the CPU is powered to off. Power to the RAM is maintained.
PAGE 69
AFL2-10A-N28 Panel PC Î Wake System with Fixed Time [Disabled] Use the Wake System with Fixed Time option to specify the time the system should be roused from a suspended state.
PAGE 70
AFL2-10A-N28 Panel PC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Enabled for Windows XP CPU Configuration and Linux (OS optimized for Hyper-Threading Processor Type Intel(R) Atom(TM) Technology) and Disabled CPU N2800 @ 1.86GHz for other OS (OS not EMT64 Supported optimized for Processor Speed 1865 MHz Hyper-Threading System Bus Speed 533 MHz Technology).
PAGE 71
AFL2-10A-N28 Panel PC Î Disabled Î Enabled Disables Hyper-Threading Technology DEFAULT Enables Hyper-Threading Technology 4.3.4 SATA Configuration Use the SATA Configuration menu (BIOS Menu 6) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced SATA Port0 SATA Port1 Configure SATA as Not Present Not Present (1) IDE Mode. (2) AHCI Mode. (3) RAID Mode.
PAGE 72
AFL2-10A-N28 Panel PC 4.3.5 USB Configuration Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced USB Configuration USB Devices: 1 Keyboard, 1 Hub Legacy USB Support [Enabled] Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
PAGE 73
AFL2-10A-N28 Panel PC Î Disabled Legacy USB support disabled Î Auto Legacy USB support disabled if no USB devices are connected 4.3.6 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 8) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 74
AFL2-10A-N28 Panel PC 4.3.6.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 9) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Serial Port 1 Configuration Enable or Disable Serial Port (COM) Serial Port Device Settings [Enabled] IO=3F8h; IRQ=4 --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.
PAGE 75
AFL2-10A-N28 Panel PC Î Serial Port I/O port address is 2F8h and the IO=2F8h; IRQ=3 interrupt address is IRQ3 4.3.6.1.2 Serial Port 2 Configuration Î Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Î Î Disabled Î Enabled Disable the serial port DEFAULT Enable the serial port Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
PAGE 76
AFL2-10A-N28 Panel PC Î Î Disabled Î Enabled Disable the serial port DEFAULT Enable the serial port Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Î Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 77
AFL2-10A-N28 Panel PC 4.3.7 H/W Monitor The H/W Monitor menu (BIOS Menu 10) shows the operating temperature. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced CPU temperature System temperature Environment Temperature :+37 °C :+36 °C :+30 °C --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 78
AFL2-10A-N28 Panel PC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced COM1 Console Redirection > Console Redirection Settings [Disabled] COM3 Console Redirection > Console Redirection Settings [Disabled] Console Redirection Enable or Disable. --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 79
AFL2-10A-N28 Panel PC 4.4 iEi Feature Use the iEi Feature menu (BIOS Menu 15) to configure the auto recovery function. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Micro SD Card [Enabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes.
PAGE 80
AFL2-10A-N28 Panel PC 4.5 Chipset Use the Chipset menu (BIOS Menu 16) to access the North Bridge, South Bridge, and Integrated Graphics configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 81
AFL2-10A-N28 Panel PC 4.5.1 Host Bridge Configuration Use the Host Bridge menu (BIOS Menu 17) to configure the host bridge chipset. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset > Intel IGD Configuration Config Intel IGD Settings ******* Memory Information ******* Memory Frequency 1067 Mhz (DDR3) Total Memory 1024 MB DIMM#1 1024 MB --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt.
PAGE 82
AFL2-10A-N28 Panel PC Î IGFX - Boot Type [VBIOS Default] Use the IGFX – Boot Type option to select the display device used by the system when it boots. Configuration option is listed below. Î VBIOS Default DEFAULT LCD Panel Type [800x600-18BIT] Use the LCD Panel Type option to select the type of flat panel connected to the system. Configuration option is listed below. Î 800x600-18BIT DEFAULT Active LFP [Int-LVDS] Use the Active LFP option to select the Active LFP configuration.
PAGE 83
AFL2-10A-N28 Panel PC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Auto Power Button Status [OFF] WIFI Function DMIC Function Blue Tooth Function Power Saving Function Restore AC Power Loss [Enabled] [Enabled] [Enabled] [Disabled] [Last State] WIFI Function --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219.
PAGE 84
AFL2-10A-N28 Panel PC Î Power Saving Function [Disabled] Use the Power Saving Function BIOS option to enable or disable the power saving function. Î Disabled Î Enabled DEFAULT Power saving function is disabled. Power saving function is enabled. It will reduce power consumption when the system is off. Î Restore on AC Power Loss [Last State] Use the Restore on AC Power Loss BIOS option to specify what state the system returns to if there is a sudden loss of power to the system.
PAGE 85
AFL2-10A-N28 Panel PC Î Bootup NumLock State [On] Use the Bootup NumLock State BIOS option to specify if the number lock setting must be modified during boot up. Î On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.
PAGE 86
AFL2-10A-N28 Panel PC Î Force DEFAULT Sets display mode to force BIOS. BIOS Î Sets display mode to current. Keep Current Î UEFI Boot [Disabled] Use the UEFI Boot BIOS option to enable or disable UEFI boot. Î Enable UEFI boot if the 1st boot device is a GPT Enabled HDD. Î Disabled DEFAULT Disable UEFI boot. 4.7 Security Use the Security menu (BIOS Menu 22) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 87
AFL2-10A-N28 Panel PC Î User Password Use the User Password field to set or change a user password. 4.8 Save & Exit Use the Save & Exit menu (BIOS Menu 19) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Reset the system after saving the changes.
PAGE 88
AFL2-10A-N28 Panel PC Î Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults. Î Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options.
PAGE 89
AFL2-10A-N28 Panel PC Chapter 5 5 Software Drivers Page 72
PAGE 90
AFL2-10A-N28 Panel PC 5.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system: Chipset Graphic Touch Audio LAN USB 3.0 Wi-Fi Bluetooth Camera Installation instructions are given below. 5.
PAGE 91
AFL2-10A-N28 Panel PC Figure 5-1: Drivers 5.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list. (See Section 5.2) Step 2: Click “Chipset.” Step 3: Locate the setup file and double click on it. Step 4: The setup files are extracted as shown in Figure 5-2.
PAGE 92
AFL2-10A-N28 Panel PC Figure 5-2: Chipset Driver Screen Step 5: When the setup files are completely extracted the Welcome Screen in Figure 5-3 appears. Step 6: Click Next to continue. Figure 5-3: Chipset Driver Welcome Screen Step 7: The license agreement in Figure 5-4 appears. Step 8: Read the License Agreement.
PAGE 93
AFL2-10A-N28 Panel PC Step 9: Click Yes to continue. Figure 5-4: Chipset Driver License Agreement Step 10: The Read Me file in Figure 5-5 appears. Figure 5-5: Chipset Driver Read Me File Step 11: Click Next to continue Step 12: Once the setup process is complete, click Finish.
PAGE 94
AFL2-10A-N28 Panel PC Figure 5-6: Chipset Driver Setup Operations 5.4 Graphics Driver Installation To install the Graphics driver, please do the following. Step 1: Access the driver list. (See Section 5.2) Step 2: Click “Graphic” and select the folder which corresponds to your operating system. Step 3: Double click the setup file. Step 4: The Welcome Screen in Figure 5-7 appears. Step 5: Click Next to continue.
PAGE 95
AFL2-10A-N28 Panel PC Figure 5-7: Graphics Driver Welcome Screen Step 6: The License Agreement in Figure 5-8 appears. Step 7: Click Yes to accept the agreement and continue. Figure 5-8: Graphics Driver License Agreement Step 8: The Read Me file in Figure 5-9 appears. Step 9: Click Next to continue.
PAGE 96
AFL2-10A-N28 Panel PC Figure 5-9: Graphics Driver Read Me File Step 10: Setup Operations are performed as shown in Figure 5-10. Step 11: Once the Setup Operations are complete, click Next to continue. Figure 5-10: Graphics Driver Setup Operations Step 12: The Finish Screen in Figure 5-11 appears. Step 13: Select “Yes, I want to restart this computer now” and click Finish.
PAGE 97
AFL2-10A-N28 Panel PC Figure 5-11: Graphics Driver Installation Finish Screen 5.5 Touch Screen Driver To install the touch panel software driver, please follow the steps below. Step 1: Access the driver list. (See Section 5.2) Step 2: Click “Touch”. Step 3: Locate the setup file and double click on it. Step 4: A Welcome Screen appears (Figure 5-12). Step 5: Click NEXT to continue.
PAGE 98
AFL2-10A-N28 Panel PC Figure 5-12: Touch Screen Driver Welcome Screen Step 6: The License Agreement shown in Figure 5-13 appears. Step 7: Click I AGREE to accept and continue. Figure 5-13: Touch Screen Driver License Agreement Step 8: Browse for an install location or use the one suggested (Figure 5-14). Step 9: Click INSTALL to continue.
PAGE 99
AFL2-10A-N28 Panel PC Figure 5-14: Touch Screen Driver Choose Install Location Step 10: The Install screen appears and displays the progress of the installation (Figure 5-15). Step 11: Click NEXT to continue. Figure 5-15: Touch Screen Driver Installation Screen Step 12: When the installation is complete, click FINISH to exit setup. (Figure 5-16).
PAGE 100
AFL2-10A-N28 Panel PC Figure 5-16: Touch Screen Driver Update Complete 5.5.1 Calibrating the Touch Screen To calibrate the touch screen cursor with the motion of the touch screen pen (or finger), please follow the steps below: Step 1: Make sure the touch screen driver is properly installed. Step 2: Locate the PenMount Monitor icon in the bottom right corner of the screen. Figure 5-17: PenMount Monitor Icon Step 3: Click the icon. A pop up menu appears. See Figure 5-18.
PAGE 101
AFL2-10A-N28 Panel PC Figure 5-18: PenMount Monitor Popup Menu Step 4: Click Control Panel in the pop up menu shown in Figure 5-18. Step 5: The configuration screen in Figure 5-19 appears. Figure 5-19: Configuration Screen Step 6: Double click the PenMount 9000 icon as shown in Figure 5-19. Step 7: The calibration initiation screen in Figure 5-20 appears. Step 8: Select the Standard Calibration button as shown in Figure 5-20.
PAGE 102
AFL2-10A-N28 Panel PC Figure 5-20: Calibration Initiation Screen Step 9: The calibration screen in is shown. See Figure 5-21. Figure 5-21: Calibration Screen Step 10: Follow the instructions. The user is asked touch the screen at five specified points after which the screen is calibrated.
PAGE 103
AFL2-10A-N28 Panel PC 5.6 Audio Driver Installation To install the audio driver, please do the following. Step 1: Access the driver list. (See Section 5.2) Step 2: Click “Audio” and select the folder which corresponds to the operating system. Step 3: Double click the setup file. Step 4: The InstallShield Wizard starts to extracting files (Figure 5-22). Figure 5-22: Audio Driver – Extracting Files Step 5: The Audio Driver Welcome message in Figure 5-23 appears.
PAGE 104
AFL2-10A-N28 Panel PC Figure 5-23: Audio Driver Welcome Screen Step 7: The audio driver installation begins. See Figure 5-24. Figure 5-24: Audio Driver Installation Step 8: When the installation is complete, the screen in Figure 5-25 appears. Step 9: Select “Yes, I want to restart my computer now” and click Finish.
PAGE 105
AFL2-10A-N28 Panel PC 5.7 LAN Driver Installation To install the LAN driver, please do the following. Step 1: Access the driver list. (See Section 5.2) Step 2: Click “LAN” and select the folder which corresponds to the operating system. Step 3: Double click the setup file. Step 4: The Welcome screen in Figure 5-26 appears. Figure 5-26: LAN Driver Welcome Screen Step 5: Click Next to continue. Step 6: The Ready to Install the Program Screen in Figure 5-27 appears.
PAGE 106
AFL2-10A-N28 Panel PC Figure 5-27: LAN Driver Ready to Install Screen Step 8: The program begins to install. Step 9: The Setup Status screen in Figure 5-28 appears. Figure 5-28: LAN Driver Setup Status Screen Step 10: When the driver installation is complete, the screen in Figure 5-29 appears. Step 11: Click Finish to exit.
PAGE 107
AFL2-10A-N28 Panel PC Figure 5-29: LAN Driver Installation Complete 5.8 USB 3.0 Driver Installation To install the touch panel software driver, please follow the steps below. Step 1: Access the driver list. (See Section 5.2) Step 2: Click “USB 3.0”. Step 3: Locate the setup file and double click on it. Step 4: A Welcome Screen appears (Figure 5-30). Step 5: Click Next to continue.
PAGE 108
AFL2-10A-N28 Panel PC Figure 5-30: USB 3.0 Driver Welcome Screen Step 6: The License Agreement shown in Figure 5-31 appears. Step 7: Accept the agreement by selecting “I accept the terms in the license agreement”. Figure 5-31: USB 3.0 Driver License Agreement Step 8: Click NEXT to continue.
PAGE 109
AFL2-10A-N28 Panel PC Figure 5-32: USB 3.0 Driver Installation Step 9: The Install screen appears and displays the progress of the installation. Step 10: When the installation is complete, click Finish to exit setup. (Figure 5-33). Figure 5-33: USB 3.
PAGE 110
AFL2-10A-N28 Panel PC 5.9 Wi-Fi Driver Installation To install the wireless LAN driver, please follow the steps below. Step 1: Access the driver list. (See Section 5.2) Step 2: Click “WiFi” and select the folder which corresponds to your operating system. Step 3: Double click the setup file. Step 4: The License Agreement screen in Figure 5-34 appears. Figure 5-34: License Agreement Step 5: Accept the conditions of the license agreement and click NEXT to continue.
PAGE 111
AFL2-10A-N28 Panel PC Figure 5-35: Setup Type Step 7: Select “Install driver and Ralink WLAN Utility” and click NEXT to continue. Step 8: The Configuration Tool screen in Figure 5-36 appears. Figure 5-36: Configuration Tool Step 9: Select “Ralink Configuration Tool”and click NEXT to continue. Step 10: The Ready to Install the Program screen in Figure 5-37 appears.
PAGE 112
AFL2-10A-N28 Panel PC Figure 5-37: Ready to Install the Program Step 11: Click Install to proceed with the installation. Step 12: The Setup Status screen in Figure 5-38 appears and displays the progress of the installation. Figure 5-38: Setup Status Step 13: When the driver installation is complete, the screen in Figure 5-39 appears.
PAGE 113
AFL2-10A-N28 Panel PC Figure 5-39: Installation Complete Step 14: Click FINISH to complete installation. 5.10 Bluetooth Driver To install the Bluetooth software driver, please follow the steps below. Step 1: Access the driver list. (See Section 5.2) Step 2: Click “Bluetooth” and select the folder which corresponds to your operating system. Step 3: Double click the setup file. Step 4: The Welcome Screen appears (Figure 5-40). Step 5: Click NEXT to continue the installation process.
PAGE 114
AFL2-10A-N28 Panel PC Figure 5-40: Welcome Screen Step 6: The License Agreement appears as shown in Figure 5-41. Step 7: Agree to the license by selecting “I accept the terms in the license agreement” and click NEXT. Figure 5-41: License Agreement Step 8: Browse for an install location or use the one suggested (Figure 5-42) and click NEXT.
PAGE 115
AFL2-10A-N28 Panel PC Figure 5-42: Bluetooth Driver Destination Folder Step 9: The Installshield Wizard is ready to install the program. Step 10: Click INSTALL to continue (Figure 5-43). Figure 5-43: Ready to Install the Program Step 11: The installation screen appears and displays the progress of the installation (Figure 5-44).
PAGE 116
AFL2-10A-N28 Panel PC Figure 5-44: Installing BlueSoleil Step 12: When the installation process is complete, click FINISH. See Figure 5-45. Figure 5-45: Bluetooth Driver Complete Installation Screen Step 13: The user is then prompted to select to restart the computer now or later (Figure 5-46). For the settings to take effect, the computer must be restarted. Step 14: Click YES to restart the computer.
PAGE 117
AFL2-10A-N28 Panel PC Figure 5-46: Reboot the Computer 5.11 Camera Driver Installation To install the camera driver, please do the following. Step 1: Access the driver list. (See Section 5.2) Step 2: Click “Camera” and select the folder which corresponds to your operating system. Step 3: Double click the setup file. Step 4: The Welcome Screen in Figure 5-47 appears. Step 5: Click Next to continue.
PAGE 118
AFL2-10A-N28 Panel PC Figure 5-47: AMCap Driver Welcome Screen Step 6: Browse for an install location or use the one suggested (Figure 5-48). Step 7: Click INSTALL to continue. Figure 5-48: AMCap Driver Choose Install Location Step 8: The program begins to install. Step 9: When the driver installation is complete, the screen in Figure 5-49 appears.
PAGE 119
AFL2-10A-N28 Panel PC Step 10: Click Finish to save and exit.
PAGE 120
AFL2-10A-N28 Panel PC Chapter 6 6 System Maintenance Page 103
PAGE 121
AFL2-10A-N28 Panel PC 6.1 System Maintenance Introduction If the components of the AFL2-10A-N28 fail they must be replaced. Components that can be replaced include: SO-DIMM module WLAN module Please contact the system reseller or vendor to purchase the replacement parts. Back cover removal instructions for the AFL2-10A-N28 are described below. 6.
PAGE 122
AFL2-10A-N28 Panel PC 6.3 Turn off the Power WARNING: Failing to turn off the system before opening it can cause permanent damage to the system and serious or fatal injury to the user. Before any maintenance procedures are carried out on the system, make sure the system is turned off. To power off the system, follow the steps below: Step 1: Locate the Function and Brightness Up function keys. See Section 1.2.1.2.
PAGE 123
AFL2-10A-N28 Panel PC Step 3: Remove a total of eleven (11) retention screws from the back cover (Figure 6-1). Figure 6-1: Back Cover Retention Screws Step 4: Carefully separate the back cover from the chassis and lift the cover clear of the device Step 0: 6.4.2 Removing the Internal Cover To remove the internal cover, follow the steps below. Step 1: Remove the five (5) retention screws securing the internal cover to the chassis (Figure 6-2).
PAGE 124
AFL2-10A-N28 Panel PC Figure 6-2: Internal Cover Retention Screws Step 2: Lift the internal cover off the AFL2-10A-N28. Step 3: The internal parts will all be viewable.
PAGE 125
AFL2-10A-N28 Panel PC 6.5 Replacing Components 6.5.1 Memory Module Replacement The flat bezel panel PC is preinstalled with one 2.0 GB DDR3 memory module. If the memory module fails, follow the instructions below to replace the memory module. Step 1: Follow all anti-static procedures. See Section 6.2. Step 2: Turn off the power. See Section 6.3. Step 3: Remove the back cover. See Section 6.4.1 above. Step 4: Remove the internal back cover. See Section 6.4.2 above.
PAGE 126
AFL2-10A-N28 Panel PC Figure 6-4: DDR SO-DIMM Module Installation Step 11: Replace the internal cover and secure it to the chassis using the previously removed retention screws. Step 12: Replace the back cover and secure it using the previously removed retention screws. Step 0: 6.5.2 WLAN Card Replacement The AFL2-10A-N28 has one WLAN card slot. To replace the WLAN card, follow the instructions below. Step 1: Follow all anti-static procedures. See Section 6.2. Step 2: Turn off the power. See Section 6.3.
PAGE 127
AFL2-10A-N28 Panel PC Figure 6-5: Releasing the WLAN Card Step 7: Grasp the WLAN card by the edges and carefully pull it out of the socket (Figure 6-6). Figure 6-6: Removing the WLAN card Step 8: Install a new WLAN card by inserting the card into the slot at an angle Step 9: Push the WLAN card down until the spring retainer clips lock into place.
PAGE 128
AFL2-10A-N28 Panel PC Step 10: Connect the main (1) and auxiliary (2) antennas. The main antenna is indicated with a strip of black electrical tape. See Figure 6-7. NOTE: To ensure the WLAN module functions correctly, please make sure the WLAN antennas are attached in the proper configuration. Figure 6-7: Attaching the Antennas Step 11: Replace the internal cover and secure it to the chassis using the previously removed retention screws.
PAGE 129
AFL2-10A-N28 Panel PC 6.6 Reinstalling the Covers WARNING: Failing to reinstall the covers may result in permanent damage to the system. Please make sure all coverings are properly installed.
PAGE 130
AFL2-10A-N28 Panel PC Chapter 7 7 Interface Connectors Page 113
PAGE 131
AFL2-10A-N28 Panel PC 7.1 Peripheral Interface Connectors The AFL2-10A-N28 panel PC motherboard comes with a number of peripheral interface connectors and configuration jumpers. The connector locations are shown in Figure 7-1. The Pin 1 locations of the on-board connectors are also indicated in the diagram below. The connector pinouts for these connectors are listed in the following sections.
PAGE 132
AFL2-10A-N28 Panel PC Figure 7-2: Main Board Layout Diagram (Solder Side) 7.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. The table below shows a list of the peripheral interface connectors on the AFL2MB-15A. Pinouts of these connectors can be found in the following sections.
PAGE 133
AFL2-10A-N28 Panel PC Connector Type Label EC debug connector 18-pin header CN1 HDD connector 20-pin connector JSATA1 Hot key connector 9-pin wafer HOTKEYCN1 Hot key LED connector 8-pin wafer HOTKEYLEDCN1 LED indicator connector 16-pin header LEDCN1 LVDS connector 20-pin crimp LCD1 LVDS backlight connector 5-pin wafer INVERTER1 microSD connector 5-pin wafer MICRO_SD1 Mini USB connector 4-pin wafer MINI_USB1 PCIe Mini card slot PCIe Mini card slot MINI_PCIE1 Power button conn
PAGE 134
AFL2-10A-N28 Panel PC 7.2.1 Audio Connector (AUDIO1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 LINE_OUTR 2 LMIC1-L 3 AMP_INR 4 LMIC1-R 5 LINE_OUTL 6 FRONT_JD 7 FRONT_JD 8 MIC1_JD 9 GND_AUDIO 10 GND_AUDIO 10 y y 9 y y y y y y 2 y y 1 Table 7-2: Audio Connector (AUDIO1) Pinouts 7.2.2 Battery Connector (CN2) PIN NO. DESCRIPTION 1 VCC 2 GND Table 7-3: Battery Connector (CN2) Pinouts 7.2.3 Bluetooth USB Connector (BLUETOOTH1) PIN NO.
PAGE 135
AFL2-10A-N28 Panel PC 7.2.4 CRT Connector (VGA1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 L_RED 2 DDC_DATA 9 3 L_GREEN 4 DDC_CLK 5 L_BLUE 6 D_GND y y 7 HSYNC 8 GND 10 2 9 VSYNC 10 GND 2 18 1 y y y y y y y y y y Table 7-5: CRT Connector (VGA1) Pinouts 7.2.5 Debug Connector (LPC_DEBUG1) PIN NO. DESCRIPTION 1 PLT_RST# 2 LPC_DEBUG_CLK 3 GND 4 LPC_AD3 5 LPC_AD2 6 LPC_AD1 7 LPC_AD0 8 LPC-FRAME# 9 VCC3 Table 7-6: Debug Connector (LPC_DEBUG1) Pinouts 7.2.
PAGE 136
AFL2-10A-N28 Panel PC 15 EC_EPP_PD6 16 EC_EPP_PE 17 EC_EPP_PD7 18 EC_EPP_SLCT Table 7-7: EC Debug Connector (CN1) Pinouts 7.2.7 HDD Connector (JSATA1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 2 VCC12 3 NC 4 VCC12 5 NC 6 NC 7 GND 8 VCC5 9 SATA_RXP0_C 10 VCC5 11 SATA_RXN0_C 12 VCC5 13 GND 14 VCC5 15 SATA_TXN0_C 16 GND 17 SATA_TXP0_C 18 VCC3 19 GND 20 VCC3 Table 7-8: HDD Connector (JSTAT1) Pinouts 7.2.8 Hot Key LED Connector (HOTKEYLEDCN1) PIN NO.
PAGE 137
AFL2-10A-N28 Panel PC 7.2.9 Hot Key Connector (HOTKEYCN1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 EC_KSO0 2 EC_KSO1 3 EC_KSO2 4 EC_KSO3 5 EC_KSO4 6 EC_KSO5 7 EC_KSI6 8 EC_KSI7 9 GND Table 7-10: Hotkey Connector (HOTKEYCN1) Pinouts 7.2.10 LED Indicator Connector (LEDCN1) PIN NO. DESCRIPTION PIN NO.
PAGE 138
AFL2-10A-N28 Panel PC 17 VCC3 18 VCC_LCD 19 VCC_LCD 20 VCC_LCD Table 7-12: LVDS Connector (LCD1) Pinouts 7.2.12 LVDS Backlight Connector (INVERTER1) PIN NO. DESCRIPTION 1 BRIGHTNESS 2 GND 3 BKL_POWER 4 GND 5 ENABKL Table 7-13: LVDS Backlight Connector (INVERTER1) Pinouts 7.2.13 microSD Connector (MICRO_SD1) PIN NO. DESCRIPTION 1 VCC_MSD 2 -DATA3 3 +DATA3 4 GND 5 VCC3 Table 7-14: microSD Connector (MICRO_SD1) Pinouts 7.2.14 Mini USB Connector (MINI_USB1) PIN NO.
PAGE 139
AFL2-10A-N28 Panel PC 7.2.15 Power Button Connector (PW_BT1) PIN NO. DESCRIPTION 1 PWRBTN_SW# 2 GND Table 7-16: Power Button Connector (PW_BT1) Pinouts 7.2.16 RFID USB Connector (RFID1) PIN NO. DESCRIPTION 1 VCC 2 -DATA5 3 +DATA5 4 GND Table 7-17: RFID USB Connector (RFID1) Pinouts 7.2.17 RFID COM Connector (RFID_COM1) PIN NO. DESCRIPTION 1 VCC 2 SIN2 3 SOUT2 4 GND Table 7-18: RFID COM Connector (RFID_COM1) Pinouts 7.2.18 SATA LED Connector (JP5) PIN NO.
PAGE 140
AFL2-10A-N28 Panel PC 7.2.19 Speaker Connector (SPKR1) PIN NO. DESCRIPTION 1 SPK_OUT_P_R 2 SPK_OUT_N_R 3 SPK_OUT_N_L 4 SPK_OUT_P_L Table 7-20: Speaker Connector (SPKR1) Pinouts 7.2.20 SPI Flash Connector (SPI1) PIN NO. DESCRIPTION 1 SPI_VCC 2 SPI_2N_CS# 3 SPI_2N_MISO 4 SPI_2N_CLK 5 SPI_2N_MOSI 6 GND Table 7-21: SPI Flash Connector (SPI1) Pinouts 7.2.21 EC SPI Flash Connector (JSPI2) PIN NO.
PAGE 141
AFL2-10A-N28 Panel PC 7.2.22 Touch Panel Connector (TS1) PIN NO. DESCRIPTION 1 X+ 2 X- 3 Y+ 4 SENSE 5 X+ 6 X- 7 Y+ 8 Y- 9 GND Table 7-23: Touch Panel Connector (TS1) Pinouts 7.2.23 Touch Panel Connector (TOUCH1) PIN NO. DESCRIPTION 1 VCC 2 -DATA4 3 +DATA4 4 GND Table 7-24: Touch Panel Connector (TOUCH1) Pinouts 7.2.24 Type K Thermocouple Connector (K_TYPE1, K_TYPE2) PIN NO.
PAGE 142
AFL2-10A-N28 Panel PC 7.2.25 Webcam Connector (CAMERA1) PIN NO. DESCRIPTION 1 VCC 2 -DATA6 3 +DATA6 4 GND Table 7-26: Webcam Connector (CAMERA1) Pinouts 7.2.26 Webcam Microphone Connector (WEBCAM_DMIC1) PIN NO. DESCRIPTION 1 DMIC_CLK_R 2 DMIC_DATA_R 3 VCC 4 GND Table 7-27: Webcam Microphone Connector (WEBCAM_DMIC1) Pinouts 7.3 External Interface Panel Connectors The table below lists the rear panel connectors on the AFL2MB-15A motherboard.
PAGE 143
AFL2-10A-N28 Panel PC 7.3.1 Ethernet Connector (JP6) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DA+ 5 DC- 2 DA- 6 DB- 3 DB+ 7 DD+ 4 DC+ 8 DD- Table 7-29: Ethernet Connector (JP6) Pinouts 7.3.2 Power Connector (DC_IN1) Table 7-30: Power Connector (DC_IN1) Pinouts 7.3.3 RS-232 DB-9 Serial Ports (COM1) PIN NO. DESCRIPTION PIN NO.
PAGE 144
AFL2-10A-N28 Panel PC 7.3.4 RS-422/485 RJ-45 Serial Port (COM2) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 RXD422+ 2 NC 3 RXD422- 4 NC 5 TXD422+/TXD485+ 6 NC 7 TXD422-/TXD485- 8 NC Table 7-32: RS-422/485 Serial Port (COM2) Pinouts The serial device is connected to the system through the RJ-45 to COM port cable. The DB-9 connector pinouts of the cable are listed below. PIN NO.
PAGE 145
AFL2-10A-N28 Panel PC 7.3.6 USB 2.0 Connectors (USB1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 POWER 5 Power 2 DATA0- 6 DATA1- 3 DATA0+ 7 DATA1+ 4 GND 8 GND Table 7-35: USB 2.0 Connectors (USB1) Pinouts 7.3.7 USB 3.0 Connectors (USB3_1) PIN NO. DESCRIPTION PIN NO.
PAGE 146
AFL2-10A-N28 Panel PC 13 GND 14 GND 15 C_DDI0_DP_AUXP 16 GND 17 C_DDI0_DP_AUXN 18 C_DDI0_DP_HPD 19 GND 20 VCC 21 GND 22 GND 23 GND 24 GND Table 7-37: DisplayPort Connector (DISPLAY_PORT1) Pinouts Page 129
PAGE 147
AFL2-10A-N28 Panel PC Appendix A A Safety Precautions Page 130
PAGE 148
AFL2-10A-N28 Panel PC WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the AFL2-10A-N28. A.1 Safety Precautions Please follow the safety precautions outlined in the sections that follow: A.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times. Follow the electrostatic precautions outlined below whenever the AFL2-10A-N28 is opened.
PAGE 149
AFL2-10A-N28 Panel PC A.1.2 CPU Temperature Warning WARNING: If the CPU Temperature Alert LED shows RED, the CPU core temperature is too high. To lower the CPU temperature, lower the environment temperature or decrease the amount of running programs. A.1.3 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the AFL2-10A-N28 may result in permanent damage to the AFL2-10A-N28 and severe injury to the user.
PAGE 150
AFL2-10A-N28 Panel PC A.1.4 Product Disposal CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
PAGE 151
AFL2-10A-N28 Panel PC Except for the LCD panel, never spray or squirt liquids directly onto any other components. To clean the LCD panel, gently wipe it with a piece of soft dry cloth or a slightly moistened cloth. Never use alcohol to clean the external chassis. The interior of the AFL2-10A-N28 does not require cleaning. Keep fluids away from the AFL2-10A-N28 interior. Be cautious of all small removable components when vacuuming the AFL2-10A-N28.
PAGE 152
AFL2-10A-N28 Panel PC Appendix B B BIOS Menu Options Page 135
PAGE 153
AFL2-10A-N28 Panel PC BIOS Information .................................................................................................................48 iWDD Vendor ........................................................................................................................48 iWDD Version .......................................................................................................................49 System Date [xx/xx/xx] ...............................................................
PAGE 154
AFL2-10A-N28 Panel PC Option ROM Messages [Force BIOS].................................................................................68 UEFI Boot [Disabled] ...........................................................................................................69 Administrator Password .....................................................................................................69 User Password ......................................................................................................
PAGE 155
AFL2-10A-N28 Panel PC Appendix C C One Key Recovery Page 138
PAGE 156
AFL2-10A-N28 Panel PC C.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 157
AFL2-10A-N28 Panel PC After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section C.5. NOTE: The initial setup procedures for Linux system are described in Section C.3. C.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products. The software will fail to run and a warning message will appear when used on non-IEI hardware.
PAGE 158
AFL2-10A-N28 Panel PC partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. C.1.2 Supported Operating System The recovery CD is compatible with both Microsoft Windows and Linux operating systems (OS).
PAGE 159
AFL2-10A-N28 Panel PC Linux o o o o o o o o o o o o o o Fedora Core 12 (Constantine) Fedora Core 11 (Leonidas) Fedora Core 10 (Cambridge) Fedora Core 8 (Werewolf) Fedora Core 7 (Moonshine) RedHat RHEL-5.4 RedHat 9 (Ghirke) Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. C.
PAGE 160
AFL2-10A-N28 Panel PC The detailed descriptions are described in the following sections. NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux, most of the setup procedures are the same except for several steps described in Section C.3. C.2.1 Hardware and BIOS Setup Step 1: Make sure the system is powered off and unplugged. Step 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended.
PAGE 161
AFL2-10A-N28 Panel PC Step 2: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below. Figure C-3: Recovery Tool Setup Menu Step 4: Press <6> then .
PAGE 162
AFL2-10A-N28 Panel PC Figure C-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 163
AFL2-10A-N28 Panel PC Figure C-5: Partition Creation Commands Page 146
PAGE 164
AFL2-10A-N28 Panel PC NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.Step0: C.2.3 Install Operating System, Drivers and Applications Install the operating system onto the unlabelled partition.
PAGE 165
AFL2-10A-N28 Panel PC C.2.4 Building the Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-6: Launching the Recovery Tool Step 4: When the recovery tool setup menu appears, press <2> then .
PAGE 166
AFL2-10A-N28 Panel PC Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section C.2.2 is hidden and the recovery tool is saved in this partition. Figure C-8: Building the Recovery Partition Step 6: After completing the system configuration, press any key in the following window to reboot the system. Figure C-9: Press Any Key to Continue Step 7: Eject the recovery CD.
PAGE 167
AFL2-10A-N28 Panel PC C.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. Step 1: Turn on the system. When the following screen displays (Figure C-10), press the key to access the recovery tool.
PAGE 168
AFL2-10A-N28 Panel PC Figure C-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure C-13). Figure C-13: Symantec Ghost Path Step 5: Select the local source drive (Drive 1) as shown in Figure C-14. Then click OK.
PAGE 169
AFL2-10A-N28 Panel PC Figure C-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in Figure C-15. Then click OK. Figure C-15: Select a Source Partition from Basic Drive Step 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure C-16). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 170
AFL2-10A-N28 Panel PC Figure C-16: File Name to Copy Image to Step 8: When the Compress Image screen in Figure C-17 prompts, click High to make the image file smaller.
PAGE 171
AFL2-10A-N28 Panel PC Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure C-18: Image Creation Confirmation Step 10: The Symantec Ghost starts to create the factory default image (Figure C-19). Figure C-19: Image Creation Complete Step 11: When the image creation completes, a screen prompts as shown in Figure C-20. Click Continue and close the Ghost window to exit the program.
PAGE 172
AFL2-10A-N28 Panel PC Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure C-21: Press Any Key to Continue C.3 Auto Recovery Setup Procedure The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 173
AFL2-10A-N28 Panel PC Step 1: Follow the steps described in Section C.2.1 ~ Section C.2.3 to setup BIOS, create partitions and install operating system. Step 2: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD. This utility MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes.
PAGE 174
AFL2-10A-N28 Panel PC Step 4: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-24: Launching the Recovery Tool Step 5: When the recovery tool setup menu appears, press <4> then . Figure C-25: Auto Recovery Environment for Windows Step 6: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition.
PAGE 175
AFL2-10A-N28 Panel PC Figure C-26: Building the Auto Recovery Partition Step 7: After completing the system configuration, the following message prompts to confirm whether to create a factory default image. Type Y to have the system create a factory default image automatically. Type N within 6 seconds to skip this process (The default option is YES). It is suggested to choose YES for this option.
PAGE 176
AFL2-10A-N28 Panel PC Step 8: The Symantec Ghost starts to create the factory default image (Figure C-28). Figure C-28: Image Creation Complete Step 9: After completing the system configuration, press any key in the following window to restart the system. Figure C-29: Press any key to continue Step 10: Eject the One Key Recovery CD and restart the system. Step 11: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 177
AFL2-10A-N28 Panel PC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit iEi Feature ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Auto Recovery Function [Enabled] Recover from PXE [Disabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 20: IEI Feature Step 13: Save changes and restart the system.
PAGE 178
AFL2-10A-N28 Panel PC Partition 1: / Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure C-30: Partitions for Linux Step 3: Create a recovery partition. Insert the recovery CD into the optical disk drive. Follow Step 1 ~ Step 3 described in Section C.2.2. Then type the following commands (marked in red) to create a partition for recovery images.
PAGE 179
AFL2-10A-N28 Panel PC recovery partition. After completing the system configuration, press any key to reboot the system. Eject the recovery CD. Figure C-31: Manual Recovery Environment for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”. To first access the recovery tool main menu, the menu.lst must be modified. In Linux, enter Administrator (root). When prompt appears, type: cd /boot/grub vi menu.lst Figure C-32: Access menu.lst in Linux (Text Mode) Step 6: Modify the menu.
PAGE 180
AFL2-10A-N28 Panel PC Step 7: The recovery tool menu appears. (Figure C-33) Figure C-33: Recovery Tool Menu Step 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section C.2.5 to create a factory default image. Step0: C.5 Recovery Tool Functions After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section C.
PAGE 181
AFL2-10A-N28 Panel PC Figure C-34: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the factory default image (iei.GHO) created in Section C.2.5. 2. Backup system: Create a system backup image (iei_user.GHO) which will be saved in the hidden partition. 3. Restore your last backup: Restore the last system backup image 4. Manual: Enter the Symantec Ghost window to configure manually. 5. Quit: Exit the recovery tool and restart the system.
PAGE 182
AFL2-10A-N28 Panel PC C.5.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.GHO is created in the hidden Recovery partition. Figure C-35: Restore Factory Default Step 3: The screen shown in Figure C-36 appears when completed. Press any key to reboot the system.
PAGE 183
AFL2-10A-N28 Panel PC C.5.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure C-37: Backup System Step 3: The screen shown in Figure C-38 appears when system backup is complete. Press any key to reboot the system.
PAGE 184
AFL2-10A-N28 Panel PC C.5.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure C-39: Restore Backup Step 3: The screen shown in Figure C-40 appears when backup recovery is complete. Press any key to reboot the system.
PAGE 185
AFL2-10A-N28 Panel PC C.5.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press in the main menu. Step 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure C-41: Symantec Ghost Window Step 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 186
AFL2-10A-N28 Panel PC C.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 187
AFL2-10A-N28 Panel PC C.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) Step 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.conf The DHCP server sample location is shown as below: Use the following command to copy the DHCP server sample to etc/dhcpd.
PAGE 188
AFL2-10A-N28 Panel PC filename “pxelinux.0”; C.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) Step 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
PAGE 189
AFL2-10A-N28 Panel PC Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp C.6.3 Configure One Key Recovery Server Settings Step 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). Step 2: Extract the recovery package to /. #cp RecoveryR10.tar.bz2 / #cd / #tar –xvjf RecoveryR10.tar.
PAGE 190
AFL2-10A-N28 Panel PC C.6.4 Start the DHCP, TFTP and HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart C.6.5 Create Shared Directory Step 1: Install the samba. #yum install samba Step 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
PAGE 191
AFL2-10A-N28 Panel PC Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 Step 4: Edit “/etc/samba/smb.conf” for your environment. For example: Step 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer C.6.6 Setup a Client System for Auto Recovery Step 1: Disable the automatically restart function before creating the factory default image. Go to: My Computer Æ Properties Æ Advanced.
PAGE 192
AFL2-10A-N28 Panel PC Figure C-42: Disable Automatically Restart Step 2: Configure the following BIOS options of the client system. Advanced → iEi Feature → Auto Recovery Function → Enabled Advanced → iEi Feature → Recover from PXE → Enabled Boot → Launch PXE OpROM → Enabled Step 3: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1 Æ remain the default setting to boot from the original OS. Boot Option #2 Æ select the boot from LAN option.
PAGE 193
AFL2-10A-N28 Panel PC MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes. Step 6: Restart the client system from LAN. If the system encounters a Blue Screen of Death (BSoD) or a hang for around 10 minutes, it will automatically restore from the factory default image. The following screens will show when the system starts auto recovering.
PAGE 194
AFL2-10A-N28 Panel PC NOTE: A firewall or a SELinux is not in use in the whole setup process described above. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them. C.7 Other Information C.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery.
PAGE 195
AFL2-10A-N28 Panel PC Step 5: When the following window appears, press ~~to select “Specify Additional Device”.~~
~~PAGE 196~~
AFL2-10A-N28 Panel PC Step 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD. Step 7: After pressing , the system will get into the recovery tool setup menu. Continue to follow the setup procedure from Step 4 in Section C.2.2 Create Partitions to finish the whole setup process.Step0: C.7.
~~PAGE 197~~
~~AFL2-10A-N28 Panel PC Appendix D D Watchdog Timer Page 180~~
~~PAGE 198~~
AFL2-10A-N28 Panel PC NOTE: The following discussion applies to DOS. Contact IEI support or visit the IEI website for drivers for other operating systems. The Watchdog Timer is a hardware-based timer that attempts to restart the system when it stops working. The system may stop working because of external EMI or software bugs. The Watchdog Timer ensures that standalone systems like ATMs will automatically attempt to restart in the case of system problems.
~~PAGE 199~~
AFL2-10A-N28 Panel PC NOTE: The Watchdog Timer is activated through software. The software application that activates the Watchdog Timer must also deactivate it when closed. If the Watchdog Timer is not deactivated, the system will automatically restart after the Timer has finished its countdown.
~~PAGE 200~~
~~AFL2-10A-N28 Panel PC Appendix E E Hazardous Materials Disclosure Page 183~~
~~PAGE 201~~
AFL2-10A-N28 Panel PC E.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 202~~
AFL2-10A-N28 Panel PC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X Metal Fasteners X O O O O O Cable Assembly X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O O Board Assemblies Battery O: This toxic or ha
~~PAGE 203~~
AFL2-10A-N28 Panel PC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。