Owner manual

ManualsBrandsIEI Integration ManualsComputersAFL-F08A v2.40

AFL-F08A-N270 Panel PC

Page i

IEI Technology Corp.

User Manual

MODEL:

AFL-F08A-N270

Fanless All-in-one Panel PC with 1.6 GHz Intel® Atom™ CPU

TFT LCD, Wireless LAN, Touch Screen,

RS-232/422/485 and IP 64 Protection

Rev. 2.40 – 22 October, 2012

Summary of content (179 pages)

PAGE 1
AFL-F08A-N270 Panel PC IEI Technology Corp. MODEL: AFL-F08A-N270 Fanless All-in-one Panel PC with 1.6 GHz Intel® Atom™ CPU TFT LCD, Wireless LAN, Touch Screen, RS-232/422/485 and IP 64 Protection User Manual Page i Rev. 2.
PAGE 2
AFL-F08A-N270 Panel PC Revision Date Version Changes 22 October, 2012 2.40 Updated for R24 version Updated audio codec spec Added Section 3.10 and 3.11: Powering On/Off the System Added Section 5: Interface Connectors Added Appendix B: ALC892 Digital Microphone Configuration 17 July, 2012 2.21 Added Section 1.3.1: Function Keys 22 February, 2012 2.20 Updated for R22 version (optional Bluetooth support) 22 July, 2011 2.
PAGE 3
AFL-F08A-N270 Panel PC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
AFL-F08A-N270 Panel PC Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.2 FEATURES ................................................................................................................... 3 1.3 FRONT PANEL .......................................................................
PAGE 5
AFL-F08A-N270 Panel PC 3.8 MOUNTING THE SYSTEM .......................................................................................... 29 3.8.1 Wall Mounting.................................................................................................. 29 3.8.2 Panel Mounting................................................................................................ 32 3.8.3 Arm Mounting .................................................................................................. 33 3.8.
PAGE 6
AFL-F08A-N270 Panel PC 5.3.2 IDE Configuration ........................................................................................... 55 5.3.2.1 IDE Master, IDE Slave ............................................................................. 56 5.3.3 Super IO Configuration ................................................................................... 60 5.3.4 Hardware Health Configuration...................................................................... 62 5.3.5 Power Configuration.........
PAGE 7
AFL-F08A-N270 Panel PC 6.2.15 RFID Connector (JP8)................................................................................... 91 6.2.16 SATA Connector (SATA1)............................................................................... 91 6.2.17 Touch Panel Connector (TS1)........................................................................ 92 6.2.18 TTL Panel Connector (CN7).......................................................................... 92 6.2.19 JUSB Connector (JUSB1)..............
PAGE 8
AFL-F08A-N270 Panel PC C.2.2 Create Partitions ............................................................................................112 C.2.3 Install Operating System, Drivers and Applications......................................116 C.2.4 Building the Recovery Partition.....................................................................117 C.2.5 Create Factory Default Image .......................................................................119 C.3 AUTO RECOVERY SETUP PROCEDURE .................
PAGE 9
AFL-F08A-N270 Panel PC G TERMINOLOGY .....................................................................................................
PAGE 10
AFL-F08A-N270 Panel PC List of Figures Figure 1-1: AFL-F08A-N270 Flat Panel PC ...................................................................................2 Figure 1-2: AFL-F08A-N270 Front View ........................................................................................3 Figure 1-3: AFL-F08A-N270 Rear View .........................................................................................5 Figure 1-4: AFL-F08A-N270 I/O Interface Connector Panel......................................
PAGE 11
AFL-F08A-N270 Panel PC Figure 3-25: Power On/Off Function Key ...................................................................................41 Figure 4-1: AFL-F08A-N270 SO-DIMM Socket Location ...........................................................45 Figure 4-2: SO-DIMM Module Installation...................................................................................45 Figure 4-3: CompactFlash® Card Cover ....................................................................................
PAGE 12
AFL-F08A-N270 Panel PC Figure C-23: Disable Automatically Restart............................................................................ 125 Figure C-24: Launching the Recovery Tool ............................................................................ 126 Figure C-25: Auto Recovery Environment for Windows ....................................................... 126 Figure C-26: Building the Auto Recovery Partition................................................................
PAGE 13
AFL-F08A-N270 Panel PC List of Tables Table 1-1: Function Keys ...............................................................................................................4 Table 1-2: AFL-F08A-N270 System Specifications......................................................................7 Table 2-1: Packing List.................................................................................................................12 Table 2-2: Optional Items.....................................................
PAGE 14
AFL-F08A-N270 Panel PC Table 6-13: MCU Connector (JP7) Pinouts ................................................................................89 Table 6-14: MCU Connector (TS2) Pinouts ................................................................................90 Table 6-15: PCIe Mini Card Slot (CN2) Pinouts..........................................................................91 Table 6-16: RFID Connector (JP8) Pinouts ................................................................................
PAGE 15
AFL-F08A-N270 Panel PC BIOS Menus BIOS Menu 1: Main .......................................................................................................................52 BIOS Menu 2: Advanced ..............................................................................................................54 BIOS Menu 3: CPU Configuration ...............................................................................................54 BIOS Menu 4: IDE Configuration...........................................
PAGE 16
AFL-F08A-N270 Panel PC Chapter 1 1 Introduction Page 1
PAGE 17
AFL-F08A-N270 Panel PC 1.1 Overview Figure 1-1: AFL-F08A-N270 Flat Panel PC The AFL-F08A-N270 is an 8" panel PC with a frameless front panel, designed to fit in any office, business or home and featuring all the inputs and outputs for full integration. The version with multi-touch screen allows complex onscreen activities to be performed by simply using both fingers to indicate movements and actions. At the heart of the system is the 1.
PAGE 18
AFL-F08A-N270 Panel PC 1.2 Features There are four models in the AFL-F08A-N270. Both models feature the following: 1.6 GHz Intel® Atom™ N270 processor Intel® 945GSE and ICH7-M chipset Up to 2 GB One 1.0 GB 533 MHz DDR2 SDRAM SO-DIMM pre-installed (supports up to 2.0 GB 533/400 MHz DDR2 SDRAM) 802.11 b/g/n wireless module Two USB 2.0 ports IP 64 compliant front panel Touch screen (multitouch or standard) RoHS compliance 1.
PAGE 19
AFL-F08A-N270 Panel PC 1.3.1 Function Keys The front panel of the AFL-F08A-N270 contains several function keys that control audio volume, LCD brightness and power on/off. CAUTION: The function keys are locked and illuminated with low intensity light in sleep mode. Touch any function key to release key lock (the keys light up). Then, follow the descriptions below to control the system. Function Key Description Power on/off Control system power on/off.
PAGE 20
AFL-F08A-N270 Panel PC 1.4 Rear Panel The rear panel provides access to retention screw holes that support the wall mounting. Refer to Figure 1-3. 7 Figure 1-3: AFL-F08A-N270 Rear View 1.5 I/O Interface Panel The I/O interface panel located on the bottom of the AFL-F08A-N270 has the following I/O interface connectors: 1 x Audio connector 1 x 12 V DC In connector 1 x External SATA connector 1 x RS-232 connector 1 x RS-232/422/485 connector 2 x LAN connectors 2 x USB 2.
PAGE 21
AFL-F08A-N270 Panel PC Figure 1-4: AFL-F08A-N270 I/O Interface Connector Panel 1.6 Internal Overview The AFL-F08A-N270 has the following components installed internally: 1 x Motherboard 1 x 1.0 GB 533 MHz DDR2 SDRAM SO-DIMM 1 x Wireless module 1.7 System Specifications The technical specifications for the AFL-F08A-N270 systems are listed in Table 1-2. 7 Specification Description LCD Size 8" Max.
PAGE 22
AFL-F08A-N270 Panel PC Specification Description Watchdog Timer Software Programmable supports 1 sec. ~ 255 sec. system reset Audio Codec ALC892 + TPA2012 2.1w/ch CLASS D amplifier Speakers AMP 1.5 W + AMP 1.5 W (built-in stereo speakers) Camera 2-megapixel digital camera on the front panel Expansion 1 x PCIe Mini card (wireless LAN 802.11 b/g/n module) 1 x Optional Bluetooth module (USB interface, Bluetooth v 2.
PAGE 23
AFL-F08A-N270 Panel PC 1.8 Dimensions The dimensions are shown below.
PAGE 24
AFL-F08A-N270 Panel PC Figure 1-6: Rear Dimensions Page 9
PAGE 25
AFL-F08A-N270 Panel PC Chapter 2 2 Unpacking Page 10
PAGE 26
AFL-F08A-N270 Panel PC To unpack the flat panel PC, follow the steps below: WARNING! The front side LCD screen has a protective plastic cover stuck to the screen. Only remove the plastic cover after the system has been properly installed. This ensures the screen is protected during the installation process. Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the external (second) box. Step 2: Open the external (second) box.
PAGE 27
AFL-F08A-N270 Panel PC Quantity Item 1 Power adapter 1 Power cord 1 Image Power transfer cord 1 Screw kit 1 Touch pen 1 User manual CD and driver CD Table 2-1: Packing List Item Panel mounting kit (P/N: AFLPK-08) Page 12 Image
PAGE 28
AFL-F08A-N270 Panel PC Item Image Wall mounting kit (P/N: AFLWK-08) Stand (P/N:STAND-A08) Arm (P/N: ARM-11-RS) Arm (P/N: ARM-31-RS) Table 2-2: Optional Items If any of these items are missing or damaged, contact the distributor or sales representative immediately.
PAGE 29
AFL-F08A-N270 Panel PC Chapter 3 3 Installation Page 14
PAGE 30
AFL-F08A-N270 Panel PC 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the maintenance of the AFL-F08A-N270 may result in permanent damage to the AFL-F08A-N270 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the AFL-F08A-N270. Dry climates are especially susceptible to ESD.
PAGE 31
AFL-F08A-N270 Panel PC Anti-static Discharge: If a user open the rear panel of the flat panel PC, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear and anti-static wristband. 3.3 Installation and Configuration Steps The following installation steps must be followed. Step 1: Unpack the system Step 2: Install a CF card Step 3: Configure the system Step 4: Connect peripheral devices Step 5: Mount the system Step 0: 3.
PAGE 32
AFL-F08A-N270 Panel PC Step 1: Remove the retention screws and lift the cover off the flat panel PC. Figure 3-1: Back Cover Retention Screws Step 2: Use a screwdriver to gently pry the edges of the system loose. Figure 3-2: Pry The Rear Cover Off Step 3: The cover will come off easily. Slide down slightly to clear the serial port connectors.
PAGE 33
AFL-F08A-N270 Panel PC 3.5 CF Card Installation To install the CompactFlash® card, the cover plate must be removed. To remove the cover plate and install the CompactFlash® card, follow the instructions below. Step 1: Undo the CompactFlash® cover fastening screw. Figure 3-3: CompactFlash® Card Cover Screw Step 2: Slide the CompactFlash® card into the slot under the cover. Figure 3-4: CompactFlash® Install Step 3: Once installed, replace the cover and screw.
PAGE 34
AFL-F08A-N270 Panel PC 3.6 Internal Cover Removal To change jumper settings and to access most internal parts, the internal aluminum cover needs to be removed. To remove this cover, please follow the steps below. Step 1: Undo the fastening screws indicated by the arrows and circles below. Figure 3-5: Internal Cover Removal Step 2: The internal parts will all be viewable.
PAGE 35
AFL-F08A-N270 Panel PC Step 3: To reinstall the cover, just replace it and fasten the screws. Step 0: 3.7 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper.
PAGE 36
AFL-F08A-N270 Panel PC 3.7.2 Preconfigured Jumpers WARNING: Do not change the settings on the jumpers in described here. Doing so may disable or damage the system. The following jumpers are preconfigured for the AFL-F08A-N270. Users should not change these jumpers (Table 3-2). The jumper settings of the preconfigured jumpers are 7 listed in Chapter 6 for reference.
PAGE 37
AFL-F08A-N270 Panel PC Figure 3-7: AT/ATX Power Selection Switch 3.7.4 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 2-pin header Jumper Settings: See Table 3-3 Jumper Location: See Figure 3-8 7 7 If the AFL-F08A-N270 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close the pins for a few seconds then remove the jumper clip.
PAGE 38
AFL-F08A-N270 Panel PC The clear CMOS jumper settings are shown in Table 3-3. 7 Clear CMOS Description Short 1 - 2 Keep CMOS Setup Short 2 - 3 Clear CMOS Setup Default Table 3-3: Clear CMOS Jumper Settings The location of the clear CMOS jumper is shown in Figure 3-8 below. 7 Figure 3-8: Clear CMOS Jumper 3.7.
PAGE 39
AFL-F08A-N270 Panel PC JP10 Description Short 1-2 COM3 RI Pin use +12 V Short 3-4 COM3 RI Pin use RI Short 5-6 COM3 RI Pin use +5 V Default Table 3-5: COM3 Pin 9 Setting Jumper Settings The COM1 and COM3 Pin 9 Setting jumper locations are shown in Figure 3-9 below. 7 Figure 3-9: COM1 and COM3 Pin 9 Setting Jumper Locations 3.7.5.1 COM3 RS-422 and RS-485 Pinouts The pinouts for RS-422 and RS-485 operation of external serial port COM 3 are detailed below.
PAGE 40
AFL-F08A-N270 Panel PC 3.7.6 COM3 RX Function Select Jumper Jumper Label: JP9 Jumper Type: 8-pin header Jumper Settings: See Table 3-8 Jumper Location: See Figure 3-10 7 7 The COM3 RX Function Select jumper sets the communication protocol used by the RX serial communications port COM3 as RS-232, RS-422 or RS-485. The COM3 RX Function Select jumper settings are shown in Table 3-8.
PAGE 41
AFL-F08A-N270 Panel PC 3.7.7 COM3 TX Function Select Jumper Jumper Label: JP11 Jumper Type: 6-pin header Jumper Settings: See Table 3-9 Jumper Location: See Figure 3-11 7 7 The COM3 TX Function Select jumper configures the TX pin on COM3 serial port connector as RS-422 as an RS-485. The COM3 TX Function Select jumper selection options are shown in Table 3-9.
PAGE 42
AFL-F08A-N270 Panel PC 3.7.8 COM3 RS-232/422/485 Serial Port Select Jumper Jumper Label: JP6 Jumper Type: 12-pin header (four 3-pin headers combined) Jumper Settings: See Table 3-10 Jumper Location: See Figure 3-12 7 7 The COM3 RS-232/422/485 Serial Port Select jumper sets the communication protocol used by the second serial communications port (COM3) as RS-232, RS-422 or RS-485. The COM3 RS-232/422/485 Serial Port Select settings are shown in Table 3-10.
PAGE 43
AFL-F08A-N270 Panel PC Figure 3-12: COM3 RS-232/422/485 Serial Port Select Jumper Location 3.7.9 CompactFlash® Setup Jumper Label: JCF1 Jumper Type: 2-pin header Jumper Settings: See Table 3-11 Jumper Location: See Figure 3-13 7 7 The CompactFlash® slot is connected through an IDE connection. This jumper sets the CompactFlash® card as the master or slave IDE device.
PAGE 44
AFL-F08A-N270 Panel PC Figure 3-13: CompactFlash® Setup Jumper Location 3.8 Mounting the System WARNING! When mounting the system onto an arm, onto the wall or onto a panel, it is better to have more than one person to help with the installation to make sure the panel PC does not fall down and get damaged. Available mounting methods are listed in the subsections below. 3.8.1 Wall Mounting To mount the system onto the wall, please follow the steps below.
PAGE 45
AFL-F08A-N270 Panel PC Figure 3-14: Wall-mounting Bracket Step 6: Insert the four monitor mounting screws provided in the wall mount kit into the four screw holes on the real panel and tighten until the screw shank is secured against the rear panel (Figure 3-15). 7 WARNING: Please use the M4 screws provided in the wall mount kit for the rear panel. If the screw is missing, the thread depth of the replacement screw should be not more than 4 mm.
PAGE 46
AFL-F08A-N270 Panel PC Step 8: Carefully insert the screws through the holes and gently pull the monitor downwards until the monitor rests securely in the slotted holes (Figure 3-15). 7 Ensure that all four of the mounting screws fit snuggly into their respective slotted holes. NOTE: In the diagram below the bracket is already installed on the wall. Figure 3-15: Chassis Support Screws Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting bracket. (Figure 3-16).
PAGE 47
AFL-F08A-N270 Panel PC Figure 3-16: Secure the Panel PC 3.8.2 Panel Mounting To mount the AFL-F08A-N270 into a panel, please follow the steps below. Step 10: Select the position on the panel to mount the flat panel PC. Step 11: Cut out a section from the panel that corresponds to the rear panel dimensions of the flat panel PC. Take care that the panel section that is cut out is smaller than the overall size of the frame but larger than the rear part of the system body.
PAGE 48
AFL-F08A-N270 Panel PC Figure 3-17: Tighten the Panel Mounting Clamp Screws 3.8.3 Arm Mounting The AFL-F08A-N270 is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 75mm interface pad. To mount the AFL-F08A-N270 on an arm, please follow the steps below. Step 1: The arm is a separately purchased item. Please correctly mount the arm onto the surface it uses as a base. To do this, refer to the installation documentation that came with the mounting arm.
PAGE 49
AFL-F08A-N270 Panel PC Step 3: Align the retention screw holes on the mounting arm interface with those in the flat panel PC. Figure 3-18: Arm Mounting Retention Screw Holes Step 4: Secure the system to the interface pad by inserting four retention screws through the bottom of the mounting arm interface pad and into the flat panel PC. Step 0: 3.8.4 Cabinet and Rack Installation The AFL-F08A-N270 can be installed into a cabinet or rack.
PAGE 50
AFL-F08A-N270 Panel PC Figure 3-19: The Rack/Cabinet Bracket Step 2: Insert the rack mounting clamps into the pre-formed holes along the edges of the flat panel PC, behind the ABS/PC plastic frame. Step 3: Tighten the screws that pass through the rack mounting clamps until the plastic caps at the front of all the screws are firmly secured to the bracket (Figure 3-20).
PAGE 51
AFL-F08A-N270 Panel PC Figure 3-21: Install into a Rack/Cabinet Step 5: Once the AFL-F08A-N270 with the attached rack/cabinet bracket has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 3-21). 7 3.9 Bottom Panel Connectors This section provides and overview of the connectors on the bottom panel. 3.9.1 LAN Connection There are two external RJ-45 LAN connectors.
PAGE 52
AFL-F08A-N270 Panel PC Figure 3-22: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the onboard RJ-45 connector. Step 0: 3.9.2 Serial Device Connection The AFL-F08A-N270 has two male DB-9 connectors on the bottom panel for serial devices to be connected. Follow the steps below to connect a serial device to the AFL-F08A-N270. Step 1: Locate the DB-9 connector. The location of the DB-9 connector is shown in Chapter 2.
PAGE 53
AFL-F08A-N270 Panel PC Figure 3-23: Serial Device Connector Step 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. 3.9.2.1 COM1 Pinouts The pinouts for COM1 are listed in the table below.
PAGE 54
AFL-F08A-N270 Panel PC 3.9.2.2 COM3 Pinouts The pinouts for COM3 are listed in the table below. Pin RS-232 RS-422 RS-485 1 NDCDB TX- D- 2 NRXDB TX+ D+ 3 NTX3 4 NDTR3 5 GND 6 NDSRB RX- 7 NRTSB RX+ 8 NCTS3 9 COM_RI3 10 GND Table 3-13: COM3 Connector Pinouts 3.9.3 USB Device Connection There are two external USB connectors. All connectors are perpendicular to the AFL-F08A-N270. To connect a USB device, please follow the instructions below. Step 1: Located the USB connectors.
PAGE 55
AFL-F08A-N270 Panel PC Step 2: Align the connectors. Align the USB device connector with one of the connectors on the bottom panel. Figure 3-24: USB Device Connection Step 3: Insert the device connector. Once aligned, gently insert the USB device connector into the onboard connector. 3.10 Powering On the System WARNING: Make sure a power supply with the correct input voltage is being fed into the system.
PAGE 56
AFL-F08A-N270 Panel PC Step 2: Press the power on/off function key on the front panel to wake the function keys. All of the function keys light up with high intensity light. Remove the finger from the function key. Step 3: Press the power on/off function key again and hold down for five (5) seconds until all function keys start flashing. After a five-time flash, the system starts to boot-up. The power on/off function key is shown in Figure 3-25. 76 Figure 3-25: Power On/Off Function Key 3.
PAGE 57
AFL-F08A-N270 Panel PC Chapter 4 4 System Maintenance Page 42
PAGE 58
AFL-F08A-N270 Panel PC 4.1 System Maintenance Introduction If the components of the AFL-F08A-N270 fail they must be replaced. Components that can be replaced include: CF Module Wireless LAN module SO-DIMM module Please contact the system reseller or vendor to purchase the replacement parts. Back cover removal instructions for the AFL-F08A-N270 are described below. 4.
PAGE 59
AFL-F08A-N270 Panel PC Only handle the edges of the PCB: - When handling the PCB, hold the PCB by the edges. 4.3 Turn off the Power WARNING: Failing to turn off the system before opening can cause permanent damage to the system and serious or fatal injury to the user. Before any maintenance procedures are carried out on the system, make sure the system is turned off. 4.4 Opening the System Remove the rear cover as shown in Section 3.4. 7 Remove the internal cover as shown in Section 3.6. 7 4.
PAGE 60
AFL-F08A-N270 Panel PC Figure 4-1: AFL-F08A-N270 SO-DIMM Socket Location Step 2: Remove the SO-DIMM by pulling both the spring retainer clips outward from the socket. Step 3: Grasp the SO-DIMM by the edges and carefully pull it out of the socket. Step 4: Install the new SO-DIMM by pushing it into the socket at an angle (Figure 4-2). 7 Step 5: Push the SO-DIMM down. The spring retainer clips on the SO-DIMM socket clip into place and secure the SO-DIMM in the socket.
PAGE 61
AFL-F08A-N270 Panel PC 4.5.2 CF Card Replacement To install the CompactFlash® card, the cover plate must be removed. To remove the cover plate and install the CompactFlash® card, follow the instructions below. Step 1: Undo the CompactFlash® cover fastening screw. Figure 4-3: CompactFlash® Card Cover Step 2: Slide the CompactFlash® card into the slot under the cover. Figure 4-4: CompactFlash® Install Step 3: Once installed, replace the cover and screw. Step 4: Install the drivers as required.
PAGE 62
AFL-F08A-N270 Panel PC 4.6 Reinstalling the Covers Replacement is opposite to removal. First replace the aluminum cover, then the plastic cover. 4.7 Software Driver Installation NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. Installation instructions are given below.
PAGE 63
AFL-F08A-N270 Panel PC Figure 4-5: Drivers Step 4: Install the drivers as required. Step 0: NOTE: When installing the Wireless LAN card driver, make sure to select the RT3090 folder which indicates the WLAN card model installed on the system.
PAGE 64
AFL-F08A-N270 Panel PC Chapter 5 5 BIOS Page 49
PAGE 65
AFL-F08A-N270 Panel PC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2. Press the DELETE key when the “Press Del to enter SETUP” message appears on the screen. 0.
PAGE 66
AFL-F08A-N270 Panel PC Key Function F10 key Save all the CMOS changes, only for Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 5.1.4 Unable to Reboot After Configuration Changes If the computer cannot boot after changes to the system configuration is made, CMOS defaults.
PAGE 67
AFL-F08A-N270 Panel PC 5.2 Main The Main menu gives an overview of the basic system information. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit System Overview ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ AMIBIOS Version :08.00.15 Build Date :10/22/09 ID: :H720MR11 Processor Intel® Atom CPU N270 @ 1.
PAGE 68
AFL-F08A-N270 Panel PC The System Overview field also has two user configurable fields: Î System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. Î System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. 5.
PAGE 69
AFL-F08A-N270 Panel PC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Advanced Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction > > > > > > > CPU Configuration IDE Configuration SuperIO Configuration Hardware Health Configuration Power Configuration Remote Access Configuration USB Configuration ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.
PAGE 70
AFL-F08A-N270 Panel PC Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed Cache L1: Lists the CPU L1 cache size Cache L2: Lists the CPU L2 cache size Ratio Actual Value: the clock multiplier 5.3.2 IDE Configuration Use the IDE Configuration menu to change and/or set the configuration of the IDE devices installed in the system.
PAGE 71
AFL-F08A-N270 Panel PC Î Configures the on-board ATA/IDE controller to be in Enhanced Enhanced mode. In this mode, IDE channels and SATA channels are separated. This mode supports up to 6 storage devices. Some legacy OS do not support this mode. Î Legacy IDE Channels [SATA Pri, PATA Sec] Î SATA Only Î SATA Pri, PATA Sec Only the SATA drives are enabled.
PAGE 72
AFL-F08A-N270 Panel PC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Primary IDE Master ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Device :Not Detected Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Enabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
PAGE 73
AFL-F08A-N270 Panel PC Î Type [Auto] Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from after the Power-On Self-Test (POST) is complete. Î BIOS is prevented from searching for an IDE disk Not Installed drive on the specified channel. Î Auto DEFAULT The BIOS auto detects the IDE disk drive type attached to the specified channel. This setting should be used if an IDE hard disk drive is attached to the specified channel.
PAGE 74
AFL-F08A-N270 Panel PC Î BIOS is prevented from using Multi-Sector Transfer on the Disabled specified channel. The data to and from the device occurs one sector at a time. Î Auto DEFAULT BIOS auto detects Multi-Sector Transfer support on the drive on the specified channel. If supported the data transfer to and from the device occurs multiple sectors at a time.
PAGE 75
AFL-F08A-N270 Panel PC Î S.M.A.R.T [Auto] Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts impending drive failures. The S.M.A.R.T BIOS option enables or disables this function. Î Î Auto Î Disabled Prevents BIOS from using the HDD SMART feature. Î Enabled Allows BIOS to use the HDD SMART feature BIOS auto detects HDD SMART support.
PAGE 76
AFL-F08A-N270 Panel PC Î Serial Port 1 Address [3F8/IRQ4] Sets the port address and IRQ of serial port 1. Î Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 DEFAULT Serial Port 3 Address [3E8] Sets the port address of serial port 3. Î Disabled 3E8 2E8 2F0 2E0 DEFAULT Serial Port 3 IRQ [IRQ4] Sets the interrupt address of serial port 3. Î 10 11 DEFAULT Select RS232 or RS422/RS485 [RS232] Sets the communications protocol for serial port 3.
PAGE 77
AFL-F08A-N270 Panel PC 5.3.4 Hardware Health Configuration The Hardware Health Configuration menu shows the operating temperature, fan speeds and system voltages. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Hardware Health Event Monitoring ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ CPU Temperature :53ºC/127ºF System Temperature :42ºC/107F CPU Core +1.05V +3.30V +5.00V +12.0V +1.50V +1.80V 5VSB VBAT :1.184 V :1.040 V :3.290 V :4.972 V :12.224V :1.472 V :1.792 V :4.919 V :3.
PAGE 78
AFL-F08A-N270 Panel PC 5.3.5.1 ACPI Configuration Use the ACPI Configuration menu (BIOS Menu 9) to select the ACPI state when the 7 system is suspended. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit ACPI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Suspend mode [S1 (POS)] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
PAGE 79
AFL-F08A-N270 Panel PC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit APM Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Restore on AC Power Loss [Last State] Power Button Mode [On/Off] Advanced Resume Resume Resume Resume Event Controls On Ring on PCI-Express WAKE# on RTC Alarm [Disabled] [Enabled] [Disabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
PAGE 80
AFL-F08A-N270 Panel PC Î Resume on Ring [Disabled] Use the Resume on Ring BIOS option to enable activity on the RI (ring in) modem line to rouse the system from a suspend or standby state. That is, the system will be roused by an incoming call on a modem.
PAGE 81
AFL-F08A-N270 Panel PC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Configure Remote Access type and parameters ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Remote Access [Disabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
PAGE 82
AFL-F08A-N270 Panel PC NOTE: Make sure the selected COM port is enabled through the Super I/O configuration menu. Î Base Address, IRQ [3F8h,4] The Base Address, IRQ option cannot be configured and only shows the interrupt address of the serial port listed above. Î Serial Port Mode [115200 8,n,1] Use the Serial Port Mode option to select baud rate through which the console redirection is made.
PAGE 83
AFL-F08A-N270 Panel PC Î Terminal Type [ANSI] Use the Terminal Type BIOS option to specify the remote terminal type. Î ANSI Î VT100 The target terminal type is VT100 Î VT-UTF8 The target terminal type is VT-UTF8 DEFAULT The target terminal type is ANSI 5.3.7 USB Configuration Use the USB Configuration menu to read USB configuration information and configure the USB settings.
PAGE 84
AFL-F08A-N270 Panel PC Î Î Enabled Î Disabled DEFAULT USB 2.0 controller enabled USB 2.0 controller disabled Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded.
PAGE 85
AFL-F08A-N270 Panel PC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Advanced PCI/PnP Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction IRQ3 [Reserved] IRQ4 [Reserved] IRQ5 [Available] IRQ7 [Available] IRQ9 [Available] IRQ10 [Reserved] IRQ11 [Reserved] IRQ14 [Available] IRQ15 [Available] DMA DMA DMA DMA DMA DMA Channel Channel Channel Channel Channel Channel 0 1 3 5 6 7 [Available] [Available] [Available] [
PAGE 86
AFL-F08A-N270 Panel PC Î IRQ9 IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device.
PAGE 87
AFL-F08A-N270 Panel PC 5.5 Boot Use the Boot menu to configure system boot options. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Boot Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > Boot Settings Configuration ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 14: Boot 5.5.
PAGE 88
AFL-F08A-N270 Panel PC Î Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process. Î Disabled Î Enabled No POST procedures are skipped DEFAULT Some POST procedures are skipped to decrease the system boot time Î Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.
PAGE 89
AFL-F08A-N270 Panel PC Î On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit. Î Boot From LAN Support [Disabled] Use the BOOT From LAN Support option to enable the system to be booted from a remote system.
PAGE 90
AFL-F08A-N270 Panel PC 5.6 Security Use the Security menu to set system and user passwords. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Security Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Supervisor Password :Not Installed User Password :Not Installed Change Supervisor Password Change User Password ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
PAGE 91
AFL-F08A-N270 Panel PC 5.7 Chipset Use the Chipset menu to access the Northbridge and Southbridge configuration menus WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Advanced Chipset Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below section may cause system to malfunction.
PAGE 92
AFL-F08A-N270 Panel PC 5.7.1 North Bridge Configuration Use the North Bridge Chipset Configuration menu (BIOS Menu 18) to configure the 7 Northbridge chipset.
PAGE 93
AFL-F08A-N270 Panel PC Î Î Enable, 1 MB Î Enable, 8 MB 1 MB of memory used by internal graphics device DEFAULT 8 MB of memory used by internal graphics device DVMT Mode Select [DVMT Mode] Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology (DVMT) operating mode. Î A fixed portion of graphics memory is reserved as Fixed Mode graphics memory. Î DVMT Mode DEFAULT Graphics memory is dynamically allocated according to the system and graphics needs.
PAGE 94
AFL-F08A-N270 Panel PC Î 800x600 18b 1024x768 18b 1280x1024 36b 1400x1050 36b 1440x900 36b 1600x1200 36b 1024x600 18b by H/W LFP Current Jumper Setting [1024x600 18b] Displays the resolution setting of the LFP port by the on-board jumper. 5.7.2 South Bridge Configuration The South Bridge Configuration menu the Southbridge chipset to be configured.
PAGE 95
AFL-F08A-N270 Panel PC 5.8 Exit Use the Exit menu to load default BIOS values, optimal failsafe values and to save configuration changes. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Exit Options ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Load Failsafe Defaults ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.
PAGE 96
AFL-F08A-N270 Panel PC Î Load Failsafe Defaults Use the Load Failsafe Defaults option to load failsafe default values for each of the parameters on the Setup menus. F8 key can be used for this operation.
PAGE 97
AFL-F08A-N270 Panel PC Chapter 6 6 Interface Connectors Page 82
PAGE 98
AFL-F08A-N270 Panel PC 6.1 Peripheral Interface Connectors The AFL-F08A-N270 panel PC motherboard comes with a number of peripheral interface connectors and configuration jumpers. The connector locations are shown in Figure 6-1. The Pin 1 locations of the on-board connectors are also indicated in the diagram below. The connector pinouts for these connectors are listed in the following sections.
PAGE 99
AFL-F08A-N270 Panel PC Figure 6-2: Main Board Layout Diagram (Solder Side) 6.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. The table below shows a list of the peripheral interface connectors on the AFL-F08A-N270 motherboard. Pinouts of these connectors can be found in the following sections.
PAGE 100
AFL-F08A-N270 Panel PC Connector Type Label CRT connector 10-pin header CN4 DIO connector 10-pin header DIO1 HDD power connector 4-pin wafer CN1 LED indicator and button connector 10-pin header JP2 LVDS backlight connector 6-pin wafer INVERTER1 MCU connector 8-pin header TS2 10-pin header JP7 PCIe Mini card slot PCIe Mini card slot CN2 RFID connector 10-pin header JP8 SATA connector SATA connector SATA1 SO-DIMM connector SO-DIMM connector DIMM1 SPI Flash connector 8-pin h
PAGE 101
AFL-F08A-N270 Panel PC 6.2.2 Audio Speaker-out Connector (CN3) PIN NO. DESCRIPTION 1 AMP_L+ 2 AMP_L- 3 AMP_R- 4 AMP_R+ Table 6-3: Audio Speaker-out Connector (CN3) Pinouts 6.2.3 Audio MIC-in Connector (MIC1) PIN NO. DESCRIPTION 1 MIC_IN_L 2 AGND_AMP 3 MIC_JD 4 MIC1_IN_R Table 6-4: Audio MIC-in Connector (MIC1) Pinouts 6.2.4 Audio DMIC-in Connector (DMIC1) PIN NO. DESCRIPTION 1 DMIC_CLK 2 DMIC_DATA 3 +3.
PAGE 102
AFL-F08A-N270 Panel PC 6.2.5 Battery Connector (BT1) PIN NO. DESCRIPTION 1 Battery +3.3V 2 GND Table 6-6: Battery Connector (BT1) Pinouts 6.2.6 CompactFlash® Type II Slot (CF1) PIN NO. DESCRIPTION PIN NO.
PAGE 103
AFL-F08A-N270 Panel PC PIN NO. DESCRIPTION PIN NO. DESCRIPTION 24 IOCS16 49 DATA 10 25 CD2 50 GROUND2 Table 6-7: CompactFlash® Slot (CF1) Pinouts 6.2.7 CRT Connector (CN4) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DACR_RED 2 SPD2 2 3 DACG_GREEN 4 SPCLK2 5 DACB_BLUE 6 V_GND y y 7 H_SYNC 8 V_GND 1 9 9 V_SYNC 10 V_GND 10 10 y y y y y y y y Table 6-8: CRT Connector (CN4) Pinouts 6.2.8 DIO Connector (DIO1) PIN NO. DESCRIPTION PIN NO.
PAGE 104
AFL-F08A-N270 Panel PC 6.2.10 LED Indicator and Button Connector (JP2) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 PW_LED +5V 2 +5V 2 3 GND 4 HD_LED 5 SUS PW LED +5V 6 RST_SW y y 7 GND 8 GND 1 9 PW_BN 10 GND 10 y y y y y y y y 9 Table 6-11: LED Indicator and Button Connector (JP2) Pinouts 6.2.11 LVDS Backlight Connector (INVERTER1) PIN NO. DESCRIPTION 1 +12V 2 +12V 3 BLON 4 BRIGHTNESS 5 GND 6 GND Table 6-12: LVDS Backlight Connector (INVERTER1) Pinouts 6.2.
PAGE 105
AFL-F08A-N270 Panel PC 6.2.13 MCU Connector (TS2) PIN NO. DESCRIPTION 1 AUTO_DIMMING 2 LOCK_BUTTON 3 VOL+ 4 VOL- 5 BRIGHT+ 6 BRIGHT- 7 LCD_ON_OFF 8 GND Table 6-14: MCU Connector (TS2) Pinouts 6.2.14 PCIe Mini Slot (CN2) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 PCIE_WAKE# 2 VCC3 3 RESERVED 4 GND 5 RESERVED 6 1.
PAGE 106
AFL-F08A-N270 Panel PC PIN NO. DESCRIPTION PIN NO. DESCRIPTION 37 RESERVED 38 USBD+ 39 RESERVED 40 GND 41 RESERVED 42 LED_WWAN# 43 RESERVED 44 LED_WLAN# 45 RESERVED 46 LED_WPAN# 47 RESERVED 48 1.5 V 49 RESERVED 50 GND 51 RESERVED 52 VCC3 Table 6-15: PCIe Mini Card Slot (CN2) Pinouts 6.2.15 RFID Connector (JP8) PIN NO. DESCRIPTION PIN NO.
PAGE 107
AFL-F08A-N270 Panel PC 6.2.17 Touch Panel Connector (TS1) PIN NO. 8-Wire 4-Wire 5-Wire 1 Right Sense N/A N/A 2 Left Sense N/A N/A 3 Bottom Sense N/A N/A 4 Top Sense N/A Sense (S) 5 Right Excite Right LR (X) 6 Left Excite Left LL (L) 7 Bottom Excite Bottom UR (Y) 8 Top Excite Top UL (Y) 9 GND GND GND Table 6-18: Touch Panel Connector (TS1) Pinouts 6.2.18 TTL Panel Connector (CN7) PIN NO. DESCRIPTION PIN NO.
PAGE 108
AFL-F08A-N270 Panel PC 17 TFT_B2 37 GND 18 TFT_B1 38 DOTCLK 19 TFT_B0 39 GND 20 GND 40 GND Table 6-19: TTL Panel Connector (CN7) Pinouts 6.2.19 JUSB Connector (JUSB1) PIN NO. DESCRIPTION 1 +5Vsus 2 D6F- 3 D6F+ 4 GND Table 6-20: JUSB Connector (JUSB1) Pinouts 6.2.20 USB Connector (USB1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 +5Vsus 2 GND 3 D0F- 4 D0F+ 5 D0F+ 6 D0F- 7 GND 8 +5Vsus 2 y y 1 8 y y y y y y 7 Table 6-21: USB Connector (USB1) Pinouts 6.2.
PAGE 109
AFL-F08A-N270 Panel PC 6.2.22 USB Connector (USB4) PIN NO. DESCRIPTION 1 USB Power (selected by JP15) 2 D3F- 3 D3F+ 4 GND Table 6-23: USB Connector (USB4) Pinouts 6.3 External Interface Panel Connectors The table below lists the rear panel connectors on the AFL-F08A-N270 motherboard. Pinouts of these connectors can be found in the following sections.
PAGE 110
AFL-F08A-N270 Panel PC 11 13 +3.3Vsus LAN1_LINK1000 +3.3Vsus 12 14 ACT-1 LAN1_LINK100 +3.3Vsus 15 GND 16 GND 17 N/A 18 N/A Table 6-25: Ethernet Connector (LAN1, LAN2) Pinouts 6.3.2 Power Connector (CN5) PIN NO. DESCRIPTION 1 GND 2 GND 3 VCC12_IN Table 6-26: Power Connector (CN5) Pinouts 6.3.3 RS-232 Serial Ports (COM1) PIN NO. DESCRIPTION PIN NO.
PAGE 111
AFL-F08A-N270 Panel PC PIN NO. RS-232 RS-422 4 NDTR3 5 GND 6 NDSRB RX- 7 NRTSB RX+ 8 NCTS3 9 COM_RI3 10 GND RS-485 Table 6-28: COM3 Connector Pinouts 6.3.5 SATA Connector (SATA2) PIN NO. DESCRIPTION 1 GND 2 STXP_0 3 STXN_0 4 GND 5 SRXN_0 6 SRXP_0 7 GND 7 GND 7 GND Table 6-29: SATA Connector (SATA2) Pinouts 6.3.6 USB 2.0 Connectors (USB3) PIN NO. DESCRIPTION PIN NO.
PAGE 112
AFL-F08A-N270 Panel PC 6.4 Preconfigured Jumper Settings The following jumpers are preconfigured for the AFL-F08A-N270. Users should not change these jumpers (Table 6-31). It is only for reference.
PAGE 113
AFL-F08A-N270 Panel PC 6.4.3 LVDS Panel Voltage Selection Jumper (J_VLVDS1) Pin Description Short 1-2 +3.3 V (Default) Short 2-3 +5 V Table 6-34: LVDS Voltage Selection Jumper (J_VLVDS1) Settings 6.4.4 MCU LCD Type Selection Jumper (JP14) Pin Description Short 1-3 LCD Panel (Default) Short 2-4 LED Panel Table 6-35: MCU LCD Type Selection Jumper (JP14) Settings 6.4.5 MCU PWM Power Selection Jumper (JP13) Pin Description Short 1-2 +5V (Default) Short 2-3 +3.
PAGE 114
AFL-F08A-N270 Panel PC 6.4.7 Touchscreen Selection Jumper (J1) Pin Description Short 1-2 5-wire (Default) Short 3-4 4-wire Table 6-38: Touchscreen Selection Jumper (J1) Settings 6.4.8 USB2 and USB4 Power Selection Jumper (JP15) Pin Description Short 1-3 USB4 +3.3V Short 3-5 USB4 +5V (Default) Short 2-4 USB2 +3.
PAGE 115
AFL-F08A-N270 Panel PC Appendix A A BIOS Options Page 100
PAGE 116
AFL-F08A-N270 Panel PC Below is a list of BIOS configuration options in the BIOS chapter. System Overview .................................................................................................................52 System Time [xx:xx:xx] .......................................................................................................53 System Date [xx/xx/xx] ........................................................................................................
PAGE 117
AFL-F08A-N270 Panel PC USB2.0 Controller Mode [HiSpeed]....................................................................................69 IRQ#.......................................................................................................................................70 DMA Channel# [Available] ..................................................................................................71 Reserved Memory Size [Disabled] ......................................................................
PAGE 118
AFL-F08A-N270 Panel PC Appendix B B ALC892 Digital Microphone Configuration Page 103
PAGE 119
AFL-F08A-N270 Panel PC B.1 ALC892 Digital Microphone Configuration To enable the ALC892 digital microphone function, follow the steps below. Step 1: Make sure the Realtek ALC892 high definition audio driver has been installed on the system. If the audio driver has not been installed on the system, please refer to Section 4.7.
PAGE 120
AFL-F08A-N270 Panel PC Step 5: Click the Mixer ToolBox icon in the Record section (Figure B-3) 8 Figure B-3: Mixer Screen Step 6: The following screen appears (Figure B-4). Check the Enable recording 8 multi-streaming box, and then click OK.
PAGE 121
AFL-F08A-N270 Panel PC Step 7: From the dropdown list box in the Record section, select Mic in at front panel (White) (Figure B-5). 8 The digital microphone function is now enabled.
PAGE 122
AFL-F08A-N270 Panel PC Appendix C C One Key Recovery Page 107
PAGE 123
AFL-F08A-N270 Panel PC C.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 124
AFL-F08A-N270 Panel PC After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section C.5. 8 NOTE: The initial setup procedures for Linux system are described in Section C.3. 8 C.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products. The software will fail to run and a warning message will appear when used on non-IEI hardware.
PAGE 125
AFL-F08A-N270 Panel PC partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. C.1.2 Supported Operating System The recovery CD is compatible with both Microsoft Windows and Linux operating systems (OS).
PAGE 126
AFL-F08A-N270 Panel PC Linux o o o o o o o o o o o o o o Fedora Core 12 (Constantine) Fedora Core 11 (Leonidas) Fedora Core 10 (Cambridge) Fedora Core 8 (Werewolf) Fedora Core 7 (Moonshine) RedHat RHEL-5.4 RedHat 9 (Ghirke) Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. C.
PAGE 127
AFL-F08A-N270 Panel PC The detailed descriptions are described in the following sections. NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux, most of the setup procedures are the same except for several steps described in Section C.3. 8 C.2.1 Hardware and BIOS Setup Step 1: Make sure the system is powered off and unplugged. Step 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended.
PAGE 128
AFL-F08A-N270 Panel PC Step 2: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below. Figure C-3: Recovery Tool Setup Menu Step 4: Press <6> then .
PAGE 129
AFL-F08A-N270 Panel PC Figure C-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 130
AFL-F08A-N270 Panel PC Figure C-5: Partition Creation Commands Page 115
PAGE 131
AFL-F08A-N270 Panel PC NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.Step0: C.2.3 Install Operating System, Drivers and Applications Install the operating system onto the unlabelled partition.
PAGE 132
AFL-F08A-N270 Panel PC C.2.4 Building the Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-6: Launching the Recovery Tool Step 4: When the recovery tool setup menu appears, press <2> then .
PAGE 133
AFL-F08A-N270 Panel PC Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section C.2.2 is hidden and the recovery tool is saved in this partition. 8 Figure C-8: Building the Recovery Partition Step 6: After completing the system configuration, press any key in the following window to reboot the system. Figure C-9: Press Any Key to Continue Step 7: Eject the recovery CD.
PAGE 134
AFL-F08A-N270 Panel PC C.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. Step 1: Turn on the system. When the following screen displays (Figure C-10), press 8 the key to access the recovery tool.
PAGE 135
AFL-F08A-N270 Panel PC Figure C-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure C-13). 8 Figure C-13: Symantec Ghost Path Step 5: Select the local source drive (Drive 1) as shown in Figure C-14. Then click OK.
PAGE 136
AFL-F08A-N270 Panel PC Figure C-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in Figure C-15. 8 Then click OK. Figure C-15: Select a Source Partition from Basic Drive Step 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure C-16). Click Save. The factory default image will then be saved in the 8 selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 137
AFL-F08A-N270 Panel PC Figure C-16: File Name to Copy Image to Step 8: When the Compress Image screen in Figure C-17 prompts, click High to make 8 the image file smaller.
PAGE 138
AFL-F08A-N270 Panel PC Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure C-18: Image Creation Confirmation Step 10: The Symantec Ghost starts to create the factory default image (Figure C-19). 8 Figure C-19: Image Creation Complete Step 11: When the image creation completes, a screen prompts as shown in Figure C-20. 8 Click Continue and close the Ghost window to exit the program.
PAGE 139
AFL-F08A-N270 Panel PC Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure C-21: Press Any Key to Continue C.3 Auto Recovery Setup Procedure The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 140
AFL-F08A-N270 Panel PC Step 1: Follow the steps described in Section C.2.1 ~ Section C.2.3 to setup BIOS, 8 8 create partitions and install operating system. Step 2: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD. This utility MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes.
PAGE 141
AFL-F08A-N270 Panel PC Step 4: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-24: Launching the Recovery Tool Step 5: When the recovery tool setup menu appears, press <4> then . Figure C-25: Auto Recovery Environment for Windows Step 6: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition.
PAGE 142
AFL-F08A-N270 Panel PC Figure C-26: Building the Auto Recovery Partition Step 7: After completing the system configuration, the following message prompts to confirm whether to create a factory default image. Type Y to have the system create a factory default image automatically. Type N within 6 seconds to skip this process (The default option is YES). It is suggested to choose YES for this option.
PAGE 143
AFL-F08A-N270 Panel PC Step 8: The Symantec Ghost starts to create the factory default image (Figure C-28). 8 Figure C-28: Image Creation Complete Step 9: After completing the system configuration, press any key in the following window to restart the system. Figure C-29: Press any key to continue Step 10: Eject the One Key Recovery CD and restart the system. Step 11: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 144
AFL-F08A-N270 Panel PC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit iEi Feature ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Auto Recovery Function [Enabled] Recover from PXE [Disabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 21: IEI Feature Step 13: Save changes and restart the system.
PAGE 145
AFL-F08A-N270 Panel PC Partition 1: / Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure C-30: Partitions for Linux Step 3: Create a recovery partition. Insert the recovery CD into the optical disk drive. Follow Step 1 ~ Step 3 described in Section C.2.2. Then type the following 8 commands (marked in red) to create a partition for recovery images.
PAGE 146
AFL-F08A-N270 Panel PC recovery partition. After completing the system configuration, press any key to reboot the system. Eject the recovery CD. Figure C-31: Manual Recovery Environment for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”. To first access the recovery tool main menu, the menu.lst must be modified. In Linux, enter Administrator (root). When prompt appears, type: cd /boot/grub vi menu.lst Figure C-32: Access menu.lst in Linux (Text Mode) Step 6: Modify the menu.
PAGE 147
AFL-F08A-N270 Panel PC Step 7: The recovery tool menu appears. (Figure C-33) 8 Figure C-33: Recovery Tool Menu Step 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section C.2.5 to create a factory default image. Step0: 8 C.5 Recovery Tool Functions After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section C.
PAGE 148
AFL-F08A-N270 Panel PC Figure C-34: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the factory default image (iei.GHO) created in Section C.2.5. 8 2. Backup system: Create a system backup image (iei_user.GHO) which will be saved in the hidden partition. 3. Restore your last backup: Restore the last system backup image 4. Manual: Enter the Symantec Ghost window to configure manually. 5. Quit: Exit the recovery tool and restart the system.
PAGE 149
AFL-F08A-N270 Panel PC C.5.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.GHO is created in the hidden Recovery partition. Figure C-35: Restore Factory Default Step 3: The screen shown in Figure C-36 appears when completed. Press any key to 8 reboot the system.
PAGE 150
AFL-F08A-N270 Panel PC C.5.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure C-37: Backup System Step 3: The screen shown in Figure C-38 appears when system backup is complete. 8 Press any key to reboot the system.
PAGE 151
AFL-F08A-N270 Panel PC C.5.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure C-39: Restore Backup Step 3: The screen shown in Figure C-40 appears when backup recovery is complete. 8 Press any key to reboot the system.
PAGE 152
AFL-F08A-N270 Panel PC C.5.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press in the main menu. Step 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure C-41: Symantec Ghost Window Step 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 153
AFL-F08A-N270 Panel PC C.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 154
AFL-F08A-N270 Panel PC C.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) Step 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.conf The DHCP server sample location is shown as below: Use the following command to copy the DHCP server sample to etc/dhcpd.
PAGE 155
AFL-F08A-N270 Panel PC filename “pxelinux.0”; C.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) Step 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
PAGE 156
AFL-F08A-N270 Panel PC Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp C.6.3 Configure One Key Recovery Server Settings Step 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). Step 2: Extract the recovery package to /. #cp RecoveryR10.tar.bz2 / #cd / #tar –xvjf RecoveryR10.tar.
PAGE 157
AFL-F08A-N270 Panel PC C.6.4 Start the DHCP, TFTP and HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart C.6.5 Create Shared Directory Step 1: Install the samba. #yum install samba Step 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
PAGE 158
AFL-F08A-N270 Panel PC Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 Step 4: Edit “/etc/samba/smb.conf” for your environment. For example: Step 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer C.6.6 Setup a Client System for Auto Recovery Step 1: Disable the automatically restart function before creating the factory default image. Go to: My Computer Æ Properties Æ Advanced.
PAGE 159
AFL-F08A-N270 Panel PC Figure C-42: Disable Automatically Restart Step 2: Configure the following BIOS options of the client system. Advanced → iEi Feature → Auto Recovery Function → Enabled Advanced → iEi Feature → Recover from PXE → Enabled Boot → Launch PXE OpROM → Enabled Step 3: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1 Æ remain the default setting to boot from the original OS. Boot Option #2 Æ select the boot from LAN option.
PAGE 160
AFL-F08A-N270 Panel PC MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes. Step 6: Restart the client system from LAN. If the system encounters a Blue Screen of Death (BSoD) or a hang for around 10 minutes, it will automatically restore from the factory default image. The following screens will show when the system starts auto recovering.
PAGE 161
AFL-F08A-N270 Panel PC NOTE: A firewall or a SELinux is not in use in the whole setup process described above. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them. C.7 Other Information C.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery.
PAGE 162
AFL-F08A-N270 Panel PC Step 5: When the following window appears, press ~~to select “Specify Additional Device”.~~
~~PAGE 163~~
AFL-F08A-N270 Panel PC Step 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD. Step 7: After pressing , the system will get into the recovery tool setup menu. Continue to follow the setup procedure from Step 4 in Section C.2.2 Create 8 Partitions to finish the whole setup process.Step0: C.7.
~~PAGE 164~~
~~AFL-F08A-N270 Panel PC Appendix D D Watchdog Timer Page 149~~
~~PAGE 165~~
AFL-F08A-N270 Panel PC NOTE: The following discussion applies to DOS. Contact IEI support or visit the IEI website for drivers for other operating systems. The Watchdog Timer is a hardware-based timer that attempts to restart the system when it stops working. The system may stop working because of external EMI or software bugs. The Watchdog Timer ensures that standalone systems like ATMs will automatically attempt to restart in the case of system problems.
~~PAGE 166~~
AFL-F08A-N270 Panel PC NOTE: The Watchdog Timer is activated through software. The software application that activates the Watchdog Timer must also deactivate it when closed. If the Watchdog Timer is not deactivated, the system will automatically restart after the Timer has finished its countdown.
~~PAGE 167~~
~~AFL-F08A-N270 Panel PC Appendix E E Safety Precautions Page 152~~
~~PAGE 168~~
AFL-F08A-N270 Panel PC WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the AFL-F08A-N270. E.1 Safety Precautions Please follow the safety precautions outlined in the sections that follow: E.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times. Follow the electrostatic precautions outlined below whenever the AFL-F08A-N270 is opened.
~~PAGE 169~~
AFL-F08A-N270 Panel PC E.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the AFL-F08A-N270 may result in permanent damage to the AFL-F08A-N270 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the AFL-F08A-N270. Dry climates are especially susceptible to ESD.
~~PAGE 170~~
AFL-F08A-N270 Panel PC Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method. Within the European Union: EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste.
~~PAGE 171~~
AFL-F08A-N270 Panel PC Avoid eating, drinking and smoking within vicinity of the AFL-F08A-N270. E.2.2 Cleaning Tools Some components in the AFL-F08A-N270 may only be cleaned using a product specifically designed for the purpose. In such case, the product will be explicitly mentioned in the cleaning tips. Below is a list of items to use when cleaning the AFL-F08A-N270. Cloth – Although paper towels or tissues can be used, a soft, clean piece of cloth is recommended when cleaning the AFL-F08A-N270.
~~PAGE 172~~
~~AFL-F08A-N270 Panel PC Appendix F F Hazardous Materials Disclosure Page 157~~
~~PAGE 173~~
AFL-F08A-N270 Panel PC F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 174~~
AFL-F08A-N270 Panel PC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl (CR(VI)) (PBB) Ethers (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X X O O O O O X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O O Board Metal Fasteners Cable Assembly Assemblies Battery O: This toxic or haza
~~PAGE 175~~
AFL-F08A-N270 Panel PC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯 (Pb) (Hg) (Cd) (CR(VI)) (PBB) 醚 (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以
~~PAGE 176~~
~~AFL-F08A-N270 Panel PC Appendix G G Terminology Page 161~~
~~PAGE 177~~
AFL-F08A-N270 Panel PC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
~~PAGE 178~~
AFL-F08A-N270 Panel PC DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. DIO The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices.
~~PAGE 179~~
AFL-F08A-N270 Panel PC LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on.