AFL-08B-N270 User Manual IEI Technology Corp. MODEL: AFL-08B-N270 Panel PC with Touch Screen, Intel® Atom N270 1.6 GHz CPU, Gigabit Ethernet, Wireless LAN, USB 2.0 External SATA, RS-232/422/485, Audio, RoHS Compliant, IP 64 Protection User Manual Page i Rev. 2.
AFL-08B-N270 User Manual Revision Date Version Changes 21 September, 2012 2.30 Updated for R23 version Updated audio codec spec Added Section 5: Interface Connectors Added Appendix C: ALC892 Digital Microphone Configuration 22 February, 2012 2.20 Bluetooth function optional 12 July, 2011 2.10 Updated WLAN card to RT3090. Added note to Section 2.9 Driver Installation. Added Section A.1.3 Product Disposal. 29 September, 2009 1.02 Added screw torque warning 22 July, 2009 1.
AFL-08B-N270 User Manual Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
AFL-08B-N270 User Manual Table of Contents REVISION........................................................................................................................ II COPYRIGHT..................................................................................................................III TABLE OF CONTENTS................................................................................................ IV LIST OF FIGURES ............................................................................
AFL-08B-N270 User Manual 2.5.4 COM Port Pin 9 Select .................................................................................... 34 2.5.5 COM3 RX Function Select Jumper.................................................................. 35 2.5.6 COM3 TX Function Select Jumper .................................................................. 36 2.5.7 COM3 RS-232/422/485 Serial Port Select Jumper ......................................... 37 2.5.8 CompactFlash® Setup ...................................
AFL-08B-N270 User Manual 4.3.2 IDE Configuration ........................................................................................... 65 4.3.3 Super IO Configuration ................................................................................... 70 4.3.4 Hardware Health Configuration...................................................................... 72 4.3.5 Power Configuration........................................................................................ 72 4.3.
AFL-08B-N270 User Manual 5.2.18 TTL Panel Connector (CN7)........................................................................ 102 5.2.19 JUSB Connector (JUSB1)............................................................................ 103 5.2.20 USB Connector (USB1) ............................................................................... 103 5.2.21 USB Connector (USB2) ............................................................................... 103 5.2.22 USB Connector (USB4) ................
AFL-08B-N270 User Manual List of Figures Figure 1-1: AFL-08B-N270 Panel PC ...........................................................................................14 Figure 1-2: AFL-08B-N270 Front View ........................................................................................16 Figure 1-3: AFL-08B-N270 Rear View .........................................................................................17 Figure 1-4: AFL-08B-N270 I/O Interface Connector Panel..................................
AFL-08B-N270 User Manual Figure 3-3: Aluminum Cover Retention Screws ........................................................................55 Figure 3-4:AFL-08B-N270 SO-DIMM Socket Location...............................................................56 Figure 3-5: DDR2 SO-DIMM Module Installation........................................................................57 Figure 5-1: Main Board Layout Diagram (Front Side) ...............................................................
AFL-08B-N270 User Manual List of Tables Table 1-1: AFL-08B-N270 Specifications....................................................................................20 Table 2-1: Jumpers .......................................................................................................................32 Table 2-2: Preconfigured Jumpers .............................................................................................32 Table 2-3: Clear CMOS Jumper Settings.......................................
AFL-08B-N270 User Manual Table 5-16: RFID Connector (JP8) Pinouts ............................................................................. 101 Table 5-17: SATA Connector (SATA1) Pinouts ...................................................................... 101 Table 5-18: Touch Panel Connector (TS1) Pinouts ................................................................ 102 Table 5-19: TTL Panel Connector (CN7) Pinouts....................................................................
AFL-08B-N270 User Manual BIOS Menus BIOS Menu 1: Main .......................................................................................................................62 BIOS Menu 2: Advanced ..............................................................................................................64 BIOS Menu 3: CPU Configuration ...............................................................................................64 BIOS Menu 4: IDE Configuration.........................................
AFL-08B-N270 User Manual Chapter 1 1 Introduction Page 13
AFL-08B-N270 User Manual 1.1 Overview Figure 1-1: AFL-08B-N270 Panel PC The AFOLUX AFL-08B-N270 is an Intel® Atom N270 powered all-in-one touch screen panel PC with a rich variety of functions and peripheral connections. It is designed for easy and simplified integration into conference center, home automation, and building control applications.
AFL-08B-N270 User Manual 1.2 Features The AFL-08B-N270 features the following: Intel® Atom™ processor Intel® 945GSE chipset 1 GB 533 MHz DDR2 SDRAM preinstalled 802.11 b/g/n wireless module Two USB 2.0 ports One external SATA port Watchdog timer that triggers a system reset if the system hangs for some reason IP 64 compliant front panel AT or ATX power mode Touch screen RoHS compliance 1.
AFL-08B-N270 User Manual Figure 1-2: AFL-08B-N270 Front View 1.3.2 Rear Panel The rear panel provides access to the internal components of the AFL-08B-N270 and CF card slot. Refer to Figure 1-3 for back cover retention screw and VESA mount screw holes.
AFL-08B-N270 User Manual Figure 1-3: AFL-08B-N270 Rear View 1.3.3 I/O Interface Panel The I/O interface panel located on the bottom of the AFL-08B-N270 has the following I/O interface connectors: 1 x 12 V DC-IN connector 1 x Audio line-out jack 1 x External SATA port 1 x Power switch 1 x Reset button 2 x RJ-45 GbE LAN ports 1 x RS-232 serial port 1 x RS-232/422/485 serial port 2 x USB 2.
AFL-08B-N270 User Manual Figure 1-4: AFL-08B-N270 I/O Interface Connector Panel 1.4 Internal Overview The AFL-08B-N270 has the following components installed internally: 1 x Motherboard 1 x 1.0 GB 533 MHz DDR2 SDRAM SO-DIMM 1 x Wireless LAN module 2 x 1.
AFL-08B-N270 User Manual 1.5 System Specifications The technical specifications for the AFL-08B-N270 systems are listed below. Specifications AFL-08B-N270 LCD Size 8" Max Resolution 800 x 600 Brightness (cd/m2) 300 Contrast Ratio 400:1 LCD Color 262K Pixel Pitch (mm) 0.0675(H) x 0.2025(V) Viewing Angle (H-V) 130º/120º Backlight MTBF 30000 hrs CPU Intel® Atom™ N270 1.
AFL-08B-N270 User Manual Specifications AFL-08B-N270 AMP 1.5 W + 1.5 W internal speakers Audio Digital microphone Digital Camera 2-megapixel digital camera on the front panel Wireless LAN Wireless LAN 802.11 b/g/n PCIe Mini card module Bluetooth V2.
AFL-08B-N270 User Manual Height: 177 mm Depth: 43 mm Figure 1-6: AFL-08B-N270 Dimensions (mm) Page 21
AFL-08B-N270 User Manual Chapter 2 2 Installation Page 22
AFL-08B-N270 User Manual WARNING: When installing the AFL-08B-N270, make sure to: Turn the power off: Chance of electrocution. Turn off the monitor and unplug it from the power supply. Only let certified engineers change the hardware settings: Incorrect settings can cause irreparable damage to the product. Install the monitor with assistance: The product is very heavy and may be damaged by drops and bumps. Two or more people should install the panel PC.
AFL-08B-N270 User Manual 2.1 Unpack the Panel PC To unpack the panel PC, follow the steps below: WARNING! Only remove the protective plastic cover stuck to the front screen after installation. The plastic layer protects the monitor surface during installation process. Step 1: Carefully cut the tape sealing the box. Only cut deep enough to break the tape. Step 2: Open the outside box. Step 3: Carefully cut the tape sealing the box. Only cut deep enough to break the tape. Step 4: Open the inside box.
AFL-08B-N270 User Manual 1 Power cord (P/N: 32702-000400-100-RS) 1 Power transfer cord (P/N: 32702-000300-100-RS) 4 Screw kit (M4*6) (P/N: 44403-040061-RS) 1 Touch pen (P/N: 43125-0002C0-00-RS) 1 User manual CD and driver CD Optional WIN CE 6.
AFL-08B-N270 User Manual Rack mounting kit (P/N: AFLRK-08) VSTAND: (P/N: VSTAND-A10) Stand (P/N:STAND-A08) Stand (P/N:STAND-100-RS) Stand (P/N: STAND-150-RS) Arm (P/N: ARM-11-RS) Arm (P/N: ARM-31-RS) Page 26
AFL-08B-N270 User Manual Hybrid card reader (P/N: AFLP-08AMSI-U) Magnetic stripe reader (P/N: AFLP-08AMSR-U) 60 W DC/DC 9-30 VDC input vehicle power adapter: IDD-930160-KIT DC 12 V Input UPS AUPS-A10-R10 DC 9-36V Input UPS AUPS-A20-R10 Make sure all the components listed in the packing list are present. If any of these items are missing or damaged, contact the distributor or sales representative immediately. 2.
AFL-08B-N270 User Manual Figure 2-1: Back Cover Retention Screws Step 2: Lift the cover and pull down the cover a bit to make it possible to fully remove it. More strength is required to separate the cover from the chassis. Step 0: WARNING: Failing to reinstall the covers may result in permanent damage to the system. Please make sure all coverings are properly installed. WARNING: Over-tightening rear cover screws will crack the plastic frame. Maximum torque for cover screws is 5 kg-cm (0.36 lb-ft/0.
AFL-08B-N270 User Manual Step 1: Locate the CF slot cover. Remove the retention screw and CF slot cover (Figure 2-2). Figure 2-2: CF card slot location Step 2: Insert a CF card into the slot (Figure 2-3). Figure 2-3: CF Card Location Step 3: Replace the CF card slot cover. Step 4: Reinsert retention screw.
AFL-08B-N270 User Manual 2.4 AT/ATX Mode Selection AT and ATX power modes can both be used on the AFL-08B-N270. The selection is made through an AT/ATX switch on the top edge of the inner aluminum cover (Figure 2-4). To select AT mode or ATX mode, follow the steps below. Step 1: Locate the AT/ATX switch on the top edge of the aluminum cover (Figure 2-4). Figure 2-4: AT/ATX Switch Location Step 2: Adjust the AT/ATX switch. Step 0: 2.4.
AFL-08B-N270 User Manual 2.4.2 ATX Power Mode With the ATX mode selected, the AFL-08B-N270 panel PC goes in a standby mode when it is turned off. The panel PC can be easily turned on via network or a power switch in standby mode. Remote power control is perfect for advertising applications since the broadcasting time for each panel PC can be set individually and controlled remotely. Other possible application includes Security surveillance Point-of-Sale (POS) Advertising terminal 2.
AFL-08B-N270 User Manual CompactFlash® setup JCF1 2-pin header Table 2-1: Jumpers 2.5.1 Access the Jumpers To access the jumpers, remove the back cover. To remove the back cover, please refer to Section 3.3. 2.5.2 Preconfigured Jumpers WARNING: Do not change the settings on the jumpers in described here. Doing so may disable or damage the system. The following jumpers are preconfigured for the AFL-08B-N270. Users should not change these jumpers (Table 2-2).
AFL-08B-N270 User Manual 2.5.3 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 2-pin header Jumper Settings: See Table 2-3 Jumper Location: See Figure 2-5 5 5 If the AFL-08B-N270 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close the pins for a few seconds then remove the jumper clip.
AFL-08B-N270 User Manual Figure 2-5: Clear CMOS Jumper 2.5.4 COM Port Pin 9 Select Jumper Label: JP8 and JP10 Jumper Settings: See Table 2-4 Jumper Location: See Figure 2-6 5 5 Two jumpers (JP8 and JP10) configure pin 9 on COM1 and COM3 DB-9 connectors. Pin 9 on the COM1 and the COM3 DB-9 connectors can be set as the ring (RI) signal, +5 V or +12 V. The COM1 and COM3 Pin 9 Setting jumper selection options are shown in Table 5 2-4.
AFL-08B-N270 User Manual Figure 2-6: COM1 and COM3 Pin 9 Setting Jumper Locations 2.5.4.1 COM3 RS-422 and RS-485 Pinouts The pinouts for RS-422 and RS-485 operation of external serial port COM 3 are detailed below. COM 3 RS-422 Description Pin 1 TX- Pin 2 TX+ Pin 6 RX- Pin 7 RX+ Table 2-6: RS-422 Pinouts COM 3 RS-485 Description Pin 1 Data- Pin 2 Data+ Table 2-7: RS-485 Pinouts 2.5.
AFL-08B-N270 User Manual The COM3 RX Function Select jumper sets the communication protocol used by the RX serial communications port COM3 as RS-232, RS-422 or RS-485. The COM3 RX Function Select jumper settings are shown in Table 2-8. 5 COM3 RX Function Select Description Short 1-2 DET BIOS RS-232/422/485 Short 3-4 RS-232 Short 5-6 RS-422 Short 7-8 RS-485 Default Table 2-8: COM3 RX Function Select Jumper Settings The COM3 RX Function Select jumper location is shown in Figure 2-7.
AFL-08B-N270 User Manual The COM3 TX Function Select jumper configures the TX pin on COM3 serial port connector as RS-422 as an RS-485. The COM3 TX Function Select jumper selection options are shown in Table 2-9. 5 COM3 TX Function Select Description Short 1 – 3 RS-422 TX- Short 2 – 4 RS-422 TX+ Short 3 – 5 RS-485 D- Short 4 – 6 RS-485 D+ Table 2-9: COM3 TX Function Select Jumper Settings The COM3 TX Function Select jumper location is shown in Figure 2-8 below.
AFL-08B-N270 User Manual RS-232/485 Select Description Short 1-2 RS-232 Default Short 4-5 RS-232 Default Short 7-8 RS-232 Default Short 10-11 RS-232 Default Short 2-3 RS-422/485 Short 5-6 RS-422/485 Short 8-9 RS-422/485 Short 11-12 RS-422/485 Table 2-10: COM3 RS-232/422/485 Serial Port Select Jumper Settings The COM3 RS-232/422/485 Serial Port Select jumper location is shown in Figure 2-9. 5 Figure 2-9: COM3 RS-232/422/485 Serial Port Select Jumper Location 2.5.
AFL-08B-N270 User Manual The CompactFlash® slot is connected through an IDE connection. This jumper sets the CompactFlash® card as the master or slave IDE device. Setting Description Open Master (Default) Short Slave Table 2-11: CompactFlash® Setup Jumper Settings Figure 2-10: CompactFlash® Setup Jumper Location 2.
AFL-08B-N270 User Manual 2.6.1 Wall Mounting To mount the panel PC onto the wall, please follow the steps below. Step 1: Select the location on the wall for the wall-mounting bracket. Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall. Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention screws. Step 4: Align the wall-mounting bracket screw holes with the pilot holes.
AFL-08B-N270 User Manual Ensure that all four of the mounting screws fit snuggly into their respective slotted holes. NOTE: In the diagram below the bracket is already installed on the wall. Figure 2-12: Chassis Support Screws Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting bracket. (Figure 2-13).
AFL-08B-N270 User Manual Figure 2-13: Secure the Panel PC 2.6.2 Panel Mounting To mount the AFL-08B-N270 panel PC into a panel, please follow the steps below. Step 1: Select the position on the panel to mount the panel PC. Step 2: Cut out a section from the panel that corresponds to the rear panel dimensions of the panel PC.
AFL-08B-N270 User Manual Figure 2-14: AFL-08B-N270 Cutout Dimensions (units in mm) Step 3: Slide the panel PC through the hole until the aluminum frame is flush against the panel. Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of the chassis, behind the aluminum frame. Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 2-15).
AFL-08B-N270 User Manual Figure 2-15: Tighten the Panel Mounting Clamp Screws 2.6.3 Cabinet and Rack Installation The AFL-08B-N270 panel PC can be installed into a cabinet or rack. The installation procedures are similar to the panel mounting installation. To do this, please follow the steps below: NOTE: When purchasing the cabinet/rack installation bracket, make sure it is compatible with both the AFL-08B-N270 panel PC and the rack/cabinet into which the AFL-08B-N270 is installed.
AFL-08B-N270 User Manual Figure 2-16: The Rack/Cabinet Bracket Step 2: Insert the rack mounting clamps into the pre-formed holes along the edges of the panel PC, behind the ABS/PC plastic frame. Step 3: Tighten the screws that pass through the rack mounting clamps until the plastic caps at the front of all the screws are firmly secured to the bracket (Figure 2-17).
AFL-08B-N270 User Manual Figure 2-18: Install into a Rack/Cabinet Step 5: Once the panel PC with the attached rack/cabinet bracket has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 2-18). 2.6.4 Arm Mounting The AFL-08B-N270 is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 75mm interface pad. To mount the panel PC on an arm, please follow the steps below.
AFL-08B-N270 User Manual Step 2: Once the mounting arm has been firmly attached to the surface, lift the panel PC onto the interface pad of the mounting arm. Step 3: Align the retention screw holes on the mounting arm interface with those in the panel PC. The arm mount retention screw holes are shown in Figure 2-19.
AFL-08B-N270 User Manual Step 1: Locate the RJ-45 connectors on the bottom panel of the AFL-08B-N270 Series. Step 2: Align the connector. Align the RJ-45 connector on the LAN cable with one of the RJ-45 connectors on the bottom panel of the AFL-08B-N270. See Figure 2-20. Figure 2-20: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the onboard RJ-45 connector. Step 0: 2.7.
AFL-08B-N270 User Manual Step 2: Insert the serial connector. Insert the DB-9 connector of a serial device into the DB-9 connector on the external peripheral interface. See Figure 2-21. Figure 2-21: Serial Device Connector Step 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. Step 0: 2.7.2.
AFL-08B-N270 User Manual Table 2-13: RS-485 Pinouts 2.7.3 USB Device Connection There are two external USB 2.0 connectors. To connect a USB 2.0 or USB 1.1 device, please follow the instructions below. Step 1: Located the USB connectors. The locations of the USB connectors are shown in Chapter 2. Step 2: Align the connectors. Align the USB device connector with one of the connectors on the bottom panel. See Figure 2-22. Figure 2-22: USB Device Connection Step 3: Insert the device connector.
AFL-08B-N270 User Manual Step 1: Connect the power adapter to the panel PC. Step 2: Connect the power cable to the included power adapter. Step 3: Connect the power cable to the power outlet. Step0: 2.9 Driver Installation NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates.
AFL-08B-N270 User Manual Chapter 3 3 System Maintenance Page 52
AFL-08B-N270 User Manual 3.1 System Maintenance Introduction WARNING! Turn off the power before removing the back cover. Risk of electrocution. Severe damage to the product and injury to the body may occur if internal parts are touched while the power is still on. WARNING! Take antistatic precautions when working on the internal components. Some internal components are easily damaged or destroyed by electrostatic discharge. Take antistatic precautions to prevent electrostatic discharge.
AFL-08B-N270 User Manual Figure 3-1: Replaceable Components 3.2 Motherboard Replacement In the case of motherboard failure, please contact an IEI sales representative, reseller or system vendor. The motherboard is accessible after opening the rear cover. 3.3 Cover Removal To access the AFL-08B-N270 internally the back panel must be removed. To remove the back panel, please follow the steps below. Step 1: Follow all anti-static procedures. See Section A.1.2. Step 2: Turn off the power. See Section 3.1.
AFL-08B-N270 User Manual Figure 3-2: Back Cover Retention Screws Step 4: Lift the cover and pull down the cover a bit to make it possible to fully remove it. More strength is required to separate the cover from the chassis. Step 5: Remove the retention screws indicated by the arrows and circles in Figure 3-3 from the aluminum cover. Figure 3-3: Aluminum Cover Retention Screws Step 6: Lift off the cover.
AFL-08B-N270 User Manual 3.4 Memory Module Replacement The panel PC is preinstalled with a 1 GB DDR2 memory module. If the memory module is fail, follow the instructions below to replace the memory module. Step 1: Remove the aluminum back cover. See Section 3.3 above. Step 2: Locate the DDR2 SO-DIMM on the motherboard (Figure 3-4). Figure 3-4:AFL-08B-N270 SO-DIMM Socket Location Step 3: Remove the SO-DIMM by pulling both the spring retainer clips outward from the socket.
AFL-08B-N270 User Manual Figure 3-5: DDR2 SO-DIMM Module Installation 3.5 CF Card Replacement The AFL-08B-N270 has one CF Type II slot. Follow the instructions below to replace the CF card. Step 1: Follow all anti-static procedures. See Section A.1.2. Step 2: Turn off the power. See Section 3.1. Step 3: Follow the instruction listed in Section 2.3 to replace the CF card. Step 0: 3.6 Reinstalling the Covers WARNING: Failing to reinstall the covers may result in permanent damage to the system.
AFL-08B-N270 User Manual When maintenance procedures are complete, please make sure all the covers are replaced, including the following: Page 58 Aluminum cover CF card slot cover Plastic rear cover
AFL-08B-N270 User Manual Chapter 4 4 BIOS Options Page 59
AFL-08B-N270 User Manual 4.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed. 4.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2.
AFL-08B-N270 User Manual F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 4-1: BIOS Navigation Keys 4.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 4.1.
AFL-08B-N270 User Manual 4.2 Main The Main menu gives an overview of the basic system information. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit System Overview ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ AMIBIOS Version :08.00.15 Build Date :10/22/09 ID: :H731MR11 Processor Intel® Atom CPU N270 @ 1.
AFL-08B-N270 User Manual The System Overview field also has two user configurable fields: Î System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. Î System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. 4.
AFL-08B-N270 User Manual Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Advanced Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction > > > > > > > CPU Configuration IDE Configuration SuperIO Configuration Hardware Health Configuration Power Configuration Remote Access Configuration USB Configuration ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.
AFL-08B-N270 User Manual Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed Cache L1: Lists the CPU L1 cache size Cache L2: Lists the CPU L2 cache size Ratio Actual Value: the clock multiplier 4.3.2 IDE Configuration Use the IDE Configuration menu to change and/or set the configuration of the IDE devices installed in the system.
AFL-08B-N270 User Manual Î Configures the on-board ATA/IDE controller to be in Enhanced Enhanced mode. In this mode, IDE channels and SATA channels are separated. This mode supports up to 6 storage devices. Some legacy OS do not support this mode. Î Legacy IDE Channels [SATA Pri, PATA Sec] Î SATA Only Î SATA Pri, PATA Sec Only the SATA drives are enabled.
AFL-08B-N270 User Manual Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Primary IDE Master ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Device :Not Detected Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Enabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
AFL-08B-N270 User Manual Î Type [Auto] Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from after the Power-On Self-Test (POST) is complete. Î BIOS is prevented from searching for an IDE disk Not Installed drive on the specified channel. Î Auto DEFAULT The BIOS auto detects the IDE disk drive type attached to the specified channel. This setting should be used if an IDE hard disk drive is attached to the specified channel.
AFL-08B-N270 User Manual Î BIOS is prevented from using Multi-Sector Transfer on the Disabled specified channel. The data to and from the device occurs one sector at a time. Î Auto DEFAULT BIOS auto detects Multi-Sector Transfer support on the drive on the specified channel. If supported the data transfer to and from the device occurs multiple sectors at a time.
AFL-08B-N270 User Manual Î S.M.A.R.T [Auto] Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts impending drive failures. The S.M.A.R.T BIOS option enables or disables this function. Î Î Auto Î Disabled Prevents BIOS from using the HDD SMART feature. Î Enabled Allows BIOS to use the HDD SMART feature BIOS auto detects HDD SMART support.
AFL-08B-N270 User Manual Î Serial Port 1 Address [3F8/IRQ4] Sets the port address and IRQ of serial port 1. Î Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 DEFAULT Serial Port 3 Address [3E8] Sets the port address of serial port 3. Î Disabled 3E8 2E8 2F0 2E0 DEFAULT Serial Port 3 IRQ [IRQ4] Sets the interrupt address of serial port 3. Î 10 11 DEFAULT Select RS232 or RS422/RS485 [RS232] Sets the communications protocol for serial port 3.
AFL-08B-N270 User Manual 4.3.4 Hardware Health Configuration The Hardware Health Configuration menu shows the operating temperature, fan speeds and system voltages. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Hardware Health Event Monitoring ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ CPU Temperature :53ºC/127ºF System Temperature :42ºC/107F CPU Core +1.05V +3.30V +5.00V +12.0V +1.50V +1.80V 5VSB VBAT :1.184 V :1.040 V :3.290 V :4.972 V :12.224V :1.472 V :1.792 V :4.919 V :3.
AFL-08B-N270 User Manual 4.3.5.1 ACPI Configuration Use the ACPI Configuration menu (BIOS Menu 9) to select the ACPI state when the 5 system is suspended. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit ACPI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Suspend mode [S1 (POS)] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
AFL-08B-N270 User Manual Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit APM Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Restore on AC Power Loss [Last State] Power Button Mode [On/Off] Advanced Resume Resume Resume Resume Event Controls On Ring on PCI-Express WAKE# on RTC Alarm [Disabled] [Enabled] [Disabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
AFL-08B-N270 User Manual Î Resume on Ring [Disabled] Use the Resume on Ring BIOS option to enable activity on the RI (ring in) modem line to rouse the system from a suspend or standby state. That is, the system will be roused by an incoming call on a modem.
AFL-08B-N270 User Manual Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Configure Remote Access type and parameters ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Remote Access [Disabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
AFL-08B-N270 User Manual NOTE: Make sure the selected COM port is enabled through the Super I/O configuration menu. Î Base Address, IRQ [3F8h,4] The Base Address, IRQ option cannot be configured and only shows the interrupt address of the serial port listed above. Î Serial Port Mode [115200 8,n,1] Use the Serial Port Mode option to select baud rate through which the console redirection is made.
AFL-08B-N270 User Manual Î Terminal Type [ANSI] Use the Terminal Type BIOS option to specify the remote terminal type. Î ANSI Î VT100 The target terminal type is VT100 Î VT-UTF8 The target terminal type is VT-UTF8 DEFAULT The target terminal type is ANSI 4.3.7 USB Configuration Use the USB Configuration menu to read USB configuration information and configure the USB settings.
AFL-08B-N270 User Manual Î Î Enabled Î Disabled DEFAULT USB 2.0 controller enabled USB 2.0 controller disabled Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded.
AFL-08B-N270 User Manual Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Advanced PCI/PnP Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction IRQ3 [Reserved] IRQ4 [Reserved] IRQ5 [Available] IRQ7 [Available] IRQ9 [Available] IRQ10 [Reserved] IRQ11 [Reserved] IRQ14 [Available] IRQ15 [Available] DMA DMA DMA DMA DMA DMA Channel Channel Channel Channel Channel Channel 0 1 3 5 6 7 [Available] [Available] [Available]
AFL-08B-N270 User Manual Î IRQ9 IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device.
AFL-08B-N270 User Manual 4.5 Boot Use the Boot menu to configure system boot options. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Boot Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > Boot Settings Configuration ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 14: Boot 4.5.
AFL-08B-N270 User Manual Î Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process. Î Disabled Î Enabled No POST procedures are skipped DEFAULT Some POST procedures are skipped to decrease the system boot time Î Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.
AFL-08B-N270 User Manual Î On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit. Î Boot From LAN Support [Disabled] Use the BOOT From LAN Support option to enable the system to be booted from a remote system.
AFL-08B-N270 User Manual 4.6 Security Use the Security menu to set system and user passwords. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Security Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Supervisor Password :Not Installed User Password :Not Installed Change Supervisor Password Change User Password ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
AFL-08B-N270 User Manual 4.7 Chipset Use the Chipset menu to access the Northbridge and Southbridge configuration menus WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Advanced Chipset Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below section may cause system to malfunction.
AFL-08B-N270 User Manual 4.7.1 North Bridge Configuration Use the North Bridge Chipset Configuration menu (BIOS Menu 18) to configure the 5 Northbridge chipset.
AFL-08B-N270 User Manual Î Î Enable, 1 MB Î Enable, 8 MB 1 MB of memory used by internal graphics device DEFAULT 8 MB of memory used by internal graphics device DVMT Mode Select [DVMT Mode] Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology (DVMT) operating mode. Î A fixed portion of graphics memory is reserved as Fixed Mode graphics memory. Î DVMT Mode DEFAULT Graphics memory is dynamically allocated according to the system and graphics needs.
AFL-08B-N270 User Manual Î 800x600 18b 1024x768 18b 1280x1024 36b 1400x1050 36b 1440x900 36b 1600x1200 36b 1024x600 18b by H/W LFP Current Jumper Setting [1024x600 18b] Displays the resolution setting of the LFP port by the on-board jumper. 4.7.2 South Bridge Configuration The South Bridge Configuration menu the Southbridge chipset to be configured.
AFL-08B-N270 User Manual 4.8 Exit Use the Exit menu to load default BIOS values, optimal failsafe values and to save configuration changes. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Exit Options ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Load Failsafe Defaults ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.
AFL-08B-N270 User Manual Î Load Failsafe Defaults Use the Load Failsafe Defaults option to load failsafe default values for each of the parameters on the Setup menus. F8 key can be used for this operation.
AFL-08B-N270 User Manual Chapter 5 5 Interface Connectors Page 92
AFL-08B-N270 User Manual 5.1 Peripheral Interface Connectors The AFL-08B-N270 panel PC motherboard comes with a number of peripheral interface connectors and configuration jumpers. The connector locations are shown in Figure 6-1. The Pin 1 locations of the on-board connectors are also indicated in the diagram below. The connector pinouts for these connectors are listed in the following sections.
AFL-08B-N270 User Manual Figure 5-2: Main Board Layout Diagram (Solder Side) 5.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. The table below shows a list of the peripheral interface connectors on the AFL-08B-N270 motherboard. Pinouts of these connectors can be found in the following sections.
AFL-08B-N270 User Manual Connector Type Label CRT connector 10-pin header CN4 DIO connector 10-pin header DIO1 HDD power connector 4-pin wafer CN1 LED indicator and button connector 10-pin header JP2 LVDS backlight connector 6-pin wafer INVERTER1 MCU connector 8-pin header TS2 10-pin header JP7 PCIe Mini card slot PCIe Mini card slot CN2 RFID connector 10-pin header JP8 SATA connector SATA connector SATA1 SO-DIMM connector SO-DIMM connector DIMM1 SPI Flash connector 8-pin
AFL-08B-N270 User Manual 5.2.2 Audio Speaker-out Connector (CN3) PIN NO. DESCRIPTION 1 AMP_L+ 2 AMP_L- 3 AMP_R- 4 AMP_R+ Table 5-3: Audio Speaker-out Connector (CN3) Pinouts 5.2.3 Audio MIC-in Connector (MIC1) PIN NO. DESCRIPTION 1 MIC_IN_L 2 AGND_AMP 3 MIC_JD 4 MIC1_IN_R Table 5-4: Audio MIC-in Connector (MIC1) Pinouts 5.2.4 Audio DMIC-in Connector (DMIC1) PIN NO. DESCRIPTION 1 DMIC_CLK 2 DMIC_DATA 3 +3.
AFL-08B-N270 User Manual 5.2.5 Battery Connector (BT1) PIN NO. DESCRIPTION 1 Battery +3.3V 2 GND Table 5-6: Battery Connector (BT1) Pinouts 5.2.6 CompactFlash® Type II Slot (CF1) PIN NO. DESCRIPTION PIN NO.
AFL-08B-N270 User Manual PIN NO. DESCRIPTION PIN NO. DESCRIPTION 24 IOCS16 49 DATA 10 25 CD2 50 GROUND2 Table 5-7: CompactFlash® Slot (CF1) Pinouts 5.2.7 CRT Connector (CN4) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DACR_RED 2 SPD2 2 3 DACG_GREEN 4 SPCLK2 5 DACB_BLUE 6 V_GND y y 7 H_SYNC 8 V_GND 1 9 9 V_SYNC 10 V_GND 10 10 y y y y y y y y Table 5-8: CRT Connector (CN4) Pinouts 5.2.8 DIO Connector (DIO1) PIN NO. DESCRIPTION PIN NO.
AFL-08B-N270 User Manual 5.2.10 LED Indicator and Button Connector (JP2) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 PW_LED +5V 2 +5V 2 3 GND 4 HD_LED 5 SUS PW LED +5V 6 RST_SW y y 7 GND 8 GND 1 9 PW_BN 10 GND 10 y y y y y y y y 9 Table 5-11: LED Indicator and Button Connector (JP2) Pinouts 5.2.11 LVDS Backlight Connector (INVERTER1) PIN NO. DESCRIPTION 1 +12V 2 +12V 3 BLON 4 BRIGHTNESS 5 GND 6 GND Table 5-12: LVDS Backlight Connector (INVERTER1) Pinouts 5.2.
AFL-08B-N270 User Manual 5.2.13 MCU Connector (TS2) PIN NO. DESCRIPTION 1 AUTO_DIMMING 2 LOCK_BUTTON 3 VOL+ 4 VOL- 5 BRIGHT+ 6 BRIGHT- 7 LCD_ON_OFF 8 GND Table 5-14: MCU Connector (TS2) Pinouts 5.2.14 PCIe Mini Slot (CN2) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 PCIE_WAKE# 2 VCC3 3 RESERVED 4 GND 5 RESERVED 6 1.
AFL-08B-N270 User Manual PIN NO. DESCRIPTION PIN NO. DESCRIPTION 37 RESERVED 38 USBD+ 39 RESERVED 40 GND 41 RESERVED 42 LED_WWAN# 43 RESERVED 44 LED_WLAN# 45 RESERVED 46 LED_WPAN# 47 RESERVED 48 1.5 V 49 RESERVED 50 GND 51 RESERVED 52 VCC3 Table 5-15: PCIe Mini Card Slot (CN2) Pinouts 5.2.15 RFID Connector (JP8) PIN NO. DESCRIPTION PIN NO.
AFL-08B-N270 User Manual 5.2.17 Touch Panel Connector (TS1) PIN NO. 8-Wire 4-Wire 5-Wire 1 Right Sense N/A N/A 2 Left Sense N/A N/A 3 Bottom Sense N/A N/A 4 Top Sense N/A Sense (S) 5 Right Excite Right LR (X) 6 Left Excite Left LL (L) 7 Bottom Excite Bottom UR (Y) 8 Top Excite Top UL (Y) 9 GND GND GND Table 5-18: Touch Panel Connector (TS1) Pinouts 5.2.18 TTL Panel Connector (CN7) PIN NO. DESCRIPTION PIN NO.
AFL-08B-N270 User Manual 17 TFT_B2 37 GND 18 TFT_B1 38 DOTCLK 19 TFT_B0 39 GND 20 GND 40 GND Table 5-19: TTL Panel Connector (CN7) Pinouts 5.2.19 JUSB Connector (JUSB1) PIN NO. DESCRIPTION 1 +5Vsus 2 D6F- 3 D6F+ 4 GND Table 5-20: JUSB Connector (JUSB1) Pinouts 5.2.20 USB Connector (USB1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 +5Vsus 2 GND 3 D0F- 4 D0F+ 5 D0F+ 6 D0F- 7 GND 8 +5Vsus 2 y y 1 8 y y y y y y 7 Table 5-21: USB Connector (USB1) Pinouts 5.2.
AFL-08B-N270 User Manual 5.2.22 USB Connector (USB4) PIN NO. DESCRIPTION 1 USB Power (selected by JP15) 2 D3F- 3 D3F+ 4 GND Table 5-23: USB Connector (USB4) Pinouts 5.3 External Interface Panel Connectors The table below lists the rear panel connectors on the AFL-08B-N270 motherboard. Pinouts of these connectors can be found in the following sections.
AFL-08B-N270 User Manual 11 13 +3.3Vsus LAN1_LINK1000 +3.3Vsus 12 14 ACT-1 LAN1_LINK100 +3.3Vsus 15 GND 16 GND 17 N/A 18 N/A Table 5-25: Ethernet Connector (LAN1, LAN2) Pinouts 5.3.2 Power Connector (CN5) PIN NO. DESCRIPTION 1 GND 2 GND 3 VCC12_IN Table 5-26: Power Connector (CN5) Pinouts 5.3.3 RS-232 Serial Ports (COM1) PIN NO. DESCRIPTION PIN NO.
AFL-08B-N270 User Manual PIN NO. RS-232 RS-422 4 NDTR3 5 GND 6 NDSRB RX- 7 NRTSB RX+ 8 NCTS3 9 COM_RI3 10 GND RS-485 Table 5-28: COM3 Connector Pinouts 5.3.5 SATA Connector (SATA2) PIN NO. DESCRIPTION 1 GND 2 STXP_0 3 STXN_0 4 GND 5 SRXN_0 6 SRXP_0 7 GND 7 GND 7 GND Table 5-29: SATA Connector (SATA2) Pinouts 5.3.6 USB 2.0 Connectors (USB3) PIN NO. DESCRIPTION PIN NO.
AFL-08B-N270 User Manual 5.4 Preconfigured Jumper Settings The following jumpers are preconfigured for the AFL-08B-N270. Users should not change these jumpers (Table 5-31). It is only for reference.
AFL-08B-N270 User Manual 5.4.3 LVDS Panel Voltage Selection Jumper (J_VLVDS1) Pin Description Short 1-2 +3.3 V (Default) Short 2-3 +5 V Table 5-34: LVDS Voltage Selection Jumper (J_VLVDS1) Settings 5.4.4 MCU LCD Type Selection Jumper (JP14) Pin Description Short 1-3 LCD Panel (Default) Short 2-4 LED Panel Table 5-35: MCU LCD Type Selection Jumper (JP14) Settings 5.4.5 MCU PWM Power Selection Jumper (JP13) Pin Description Short 1-2 +5V (Default) Short 2-3 +3.
AFL-08B-N270 User Manual 5.4.7 Touchscreen Selection Jumper (J1) Pin Description Short 1-2 5-wire (Default) Short 3-4 4-wire Table 5-38: Touchscreen Selection Jumper (J1) Settings 5.4.8 USB2 and USB4 Power Selection Jumper (JP15) Pin Description Short 1-3 USB4 +3.3V Short 3-5 USB4 +5V (Default) Short 2-4 USB2 +3.
AFL-08B-N270 User Manual Appendix A A Safety Precautions Page 110
AFL-08B-N270 User Manual WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the AFL-08B-N270. A.1 Safety Precautions Please follow the safety precautions outlined in the sections that follow: A.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times. Follow the electrostatic precautions outlined below whenever the AFL-08B-N270 is opened.
AFL-08B-N270 User Manual A.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the AFL-08B-N270 may result in permanent damage to the AFL-08B-N270 and sever injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the AFL-08B-N270. Dry climates are especially susceptible to ESD.
AFL-08B-N270 User Manual A.1.3 Product Disposal CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
AFL-08B-N270 User Manual Except for the LCD panel, never spray or squirt liquids directly onto any other components. To clean the LCD panel, gently wipe it with a piece of soft dry cloth or a slightly moistened cloth. The interior does not require cleaning. Keep fluids away from the interior. Be careful not to damage the small, removable components inside. Turn off before cleaning. Never drop any objects or liquids through the openings.
AFL-08B-N270 User Manual Appendix B B BIOS Options Page 115
AFL-08B-N270 User Manual Below is a list of BIOS configuration options in the BIOS chapter. System Overview .................................................................................................................62 System Time [xx:xx:xx] .......................................................................................................63 System Date [xx/xx/xx] ........................................................................................................
AFL-08B-N270 User Manual USB2.0 Controller Mode [HiSpeed]....................................................................................79 IRQ#.......................................................................................................................................80 DMA Channel# [Available] ..................................................................................................81 Reserved Memory Size [Disabled] ....................................................................
AFL-08B-N270 User Manual Appendix C C ALC892 Digital Microphone Configuration Page 118
AFL-08B-N270 User Manual C.1 ALC892 Digital Microphone Configuration To enable the ALC892 digital microphone function, follow the steps below. Step 1: Make sure the Realtek ALC892 high definition audio driver has been installed on the system. If the audio driver has not been installed on the system, please refer to Section 2.9.
AFL-08B-N270 User Manual Step 5: Click the Mixer ToolBox icon in the Record section (Figure C-3) Figure C-3: Mixer Screen Step 6: The following screen appears (Figure C-4). Check the Enable recording multi-streaming box, and then click OK.
AFL-08B-N270 User Manual Step 7: From the dropdown list box in the Record section, select Mic in at front panel (White) (Figure C-5). The digital microphone function is now enabled.
AFL-08B-N270 User Manual Appendix D D Terminology Page 122
AFL-08B-N270 User Manual AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
AFL-08B-N270 User Manual DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. EHCI The Enhanced Host Controller Interface (EHCI) specification is a register-level interface description for USB 2.0 Host Controllers. EIDE Enhanced IDE (EIDE) is a newer IDE interface standard that has data transfer rates between 4.0 MBps and 16.6 MBps.
AFL-08B-N270 User Manual RAM Random Access Memory (RAM) is volatile memory that loses data when power is lost. RAM has very fast data transfer rates compared to other storage like hard drives. SATA Serial ATA (SATA) is a serial communications bus designed for data transfers between storage devices and the computer chipsets. The SATA bus has transfer speeds up to 1.5 Gbps and the SATA II bus has data transfer speeds of up to 3.0 Gbps. S.M.A.R.T Self Monitoring Analysis and Reporting Technology (S.M.A.R.
AFL-08B-N270 User Manual Appendix E E Watchdog Timer Page 126
AFL-08B-N270 User Manual NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMIs or a software bug.
AFL-08B-N270 User Manual NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
AFL-08B-N270 User Manual Appendix F F Hazardous Materials Disclosure Page 129
AFL-08B-N270 User Manual F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
AFL-08B-N270 User Manual Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X Metal Fasteners X O O O O O Cable Assembly X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O O Board Assemblies Battery O: This toxic or
AFL-08B-N270 User Manual 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求
