ADSL2/2+ Modem/Router with 4 ports switch Quick Installation Guide Contents 1. Panel Descriptions ............................................................................................... 1 2. Connecting 4 Ports ADSL2/2+ Router ................................................................. 3 3. Setting up the TCP/IP in Windows ...................................................................... 5 Windows ME/98 ................................................................................
1. Panel Descriptions 1.1 Back Panel: The back panel of the 4 Ports ADSL2/2+ Router contains ADSL, Ethernet Switches, Reset Button and Power Adaptor connection. ADSL Port for connecting to the ADSL/ADSL2/ADSL2+ Service Provider. Ports 1~4 Four 10/100Mbps Ethernet Ports for connecting to the network devices. Power Power adapter connector All the Ethernet port of the 4 Ports ADSL2/2+ Router supports ! auto-crossover capability.
1.2 Front Panel: The 4 Ports ADSL2/2+ Router’s LED indicators display information about the device’s status. PWR Lights up when 4 Ports ADSL2/2+ Router is powered on. 1 Blinking when Port 1 of this 4 Ports ADSL2/2+ Router is Sending/Receiving data. 2 Blinking when Port 2 of this 4 Ports ADSL2/2+ Router is Sending/Receiving data. 3 Blinking when Port 3 of this 4 Ports ADSL2/2+ Router is Sending/Receiving data. 4 Blinking when Port 4 of this 4 Ports ADSL2/2+ Router is Sending/Receiving data.
2. Connecting 4 Ports ADSL2/2+ Router 2.1 Connection Mechanism: This section describes the hardware connection mechanism of your 4 Ports ADSL2/2+ Router on your Local Area Network (LAN) connect to the Internet, how to configure your 4 Ports ADSL2/2+ Router for Internet access or how to manually configure your Internet connection. Before you can establish an Internet or Wireless connection through your 4 Ports ADSL2/2+ Router, make sure you have the following: 1.
2.2 Connection Steps: Following are the steps to properly connect your 4 Ports ADSL2/2+ Router: 1. Turn off your computer. 2. Connect the ADSL port of your 4 Ports ADSL2/2+ Router to the wall jack of the ADSL Line with a RJ-11 cable. 3. Connect the Ethernet cable (RJ-45) from your 4 Ports ADSL2/2+ Router to the Ethernet Adaptor in your computer. 4. Connect the Power adaptor to the 4 Ports ADSL2/2+ Router and plug the other end into a Power outlet.
3. Setting up the TCP/IP Windows Me / 98 Step 1: Click Start→Settings→Control Panel. Step 4: Go to IP Address icon and select Obtain an IP address. Step 2: Double-click the Network icon. Step 5: Go to Gateway icon and erase all previous setting. Step 3: Go to Configuration icon, select network adapter installed and click Properties. Step 6: Go to DNS Configuration icon, select Disable DNS and click OK.
Windows 2000 Step 1: Click Start→Settings→Control Panel. Step 4: Select Internet Protocol (TCP/IP) and click Properties. 1 2 Step 2: Double-click the Network and Dial-up Connections. Step 5: Select Obtain an IP address automatically and DNS server address automatically. Then, click OK. Step 3: Right Click the Local Area Connection and 1 select Properties.
Windows XP Step 1: Click Start→Control Panel→Classic View. Step 4: Go to General icon, select Internet Protocol (TCP/IP) and click Properties. 1 2 Step 2: Double-click the Network Connections. Step 5: Go to General icon, select Obtain an IP address automatically and DNS server address automatically. Then, click OK. Step 3: Right Click on the Local Area Connection and select Properties.
4. Setting up the 4 Ports ADSL2/2+ Router 1. Launch your web browser, and enter the 4 Ports ADSL2/2+ Router’s IP Address: “192.168.1.1” in the address field then press the “Enter” key to login. 2. Enter the default User Name: “Admin” and Password: “Admin”. Then press “OK” to login. ! Note that the Username and Password are case sensitive.
3. Upon entering the address into the web browser, the system HOME page with all the device information will pop up. 4. Click on “Wizard Setup” and the following screen will pop-up. The Setup Wizard is a presetting wizard which meant to help you install the 4 Ports ADSL2/2+ Router quickly and easily. Follow the Steps describe below to complete your first time installation.
Step 1: Select your country from the Country list and the ADSL service provider from the ISP List (If there are more than two ISP in your country) and note the “Encapsulation” type and “VPI & VCI” setting. Click “Next” to continue. 1 2 Click “Config” if you can’t find any available parameters from the ! presetting country list. Check your ISP immediately for the setting/configuration details.
A. For countries with the following “Encapsulation” type after clicking the “Next” button at Step 1, you will enter into set Username and Password window as shown below: PPPoA VC-Mux PPPoA LLC PPPoE VC-Mux PPPoE LLC 1 2 Manually enter your “Username” and “Password” which will be provided by your Service Provider (ISP). Click “Apply” after setup.
B. For countries with the following “Encapsulation” after clicking the “Next” button at Step 1, the following window will pop-up: 1483 Routed IP VC-Mux 1483 Routed IP LLC 1483 Routed IP LLC (1577) 1483 Bridged IP VC-Mux 1483 Bridged IP LLC In this current window, you will find TWO different Connection Type: Static (Fixed IP by ISP) DHCP (Get IP dynamically from ISP) Click “Config” if you can’t find any available parameters from the presetting country list.
1. Static: Click the radio button to enable Static (Fixed IP by ISP) option then click “Next”, the following window will pop-up. 1 2 Manually enter the “IP Address”, “Mask”, “Default Gateway” and “DNS” which will be provided by your ISP. Click “Apply” after your setting. Static Setup: Static IP Settings are for users who have a Static IP Address (WAN side) from their ISP. IP Address: This is the Static IP Address given by your ISP. Mask: This is the Subnet Mask provided by your ISP.
2. DHCP (Get IP dynamically from ISP): Click the radio button to enable DHCP (Get IP dynamically from ISP) option then click “Next”, the following window will pop-up: 1 Nothing to be filled under this mode. Just click the “Apply” button to confirm your setting.
Step 2: The following configuration home page with the device setup information will pop-up after your confirmation at Step 1. Check the following items when the above window pop-up. All the setting should be exactly the same with your setting in STEP1. Description: Show the ISP name you’d selected in STEP 1. Type: Show the Encapsulation type selected in STEP 1.
5. Making sure of Internet connection 1. Click the “Refresh” button and check the “System Information”. The “DSL Status” and “DSL Speed” under “System Information” shows you the ADSL connection status and connection speed (Upstream/Downstream) in Kbps.
2. Launch your web browser, and enter the Google Website Address: “www.google.com” in the address field then press “Enter”. 3. The following Google website index page will display on your screen. This shows your ADSL connection is correctly set and access to the Internet is now available. NOTE: For more detailed information regarding settings and connections, refer to “Users Manual”.
