Instruction Manual
49
MCP-Z Process / ISMATEC SA / 03.08.07/CB/GP
Pumpenkopf ID Code
Pump head ID Code
Tête de pompe ID Coed
Fließrate ml/min max.
1
)
Flow rate
Débit
Fließrate ml/min min.
1
)
Flow rate
Débit
Differenzdruck max. (bar)
Differential pressure (psi)
Pression différentielle
Zahnradmaterial
Gear material
Matériaux engrenage
Dichtungen
Seals
Etanchéités
Gehäusematerial
Housing material
Matériaux caisse
Systemdruck max. (bar)
System pressure (psi)
Pression de système
Betriebstemperatur
2
) ºC
Operating temperature °F
Température de fonctionnement
Bypass / Internal bypass
*)
Bypass interne
Anschlüsse (Innengewinde)
Ports (internal thread)
Ports (pas de vis interne)
Bestell-Nr. / Order No.
No. de commande
Service Kit
4
)
Magnet / Aimant
5
)
1
)
Fließraten ohne Gegendruck / Flow rate without differential pressure / Débit sans pression différentielle
2
)
Mit anderen Dichtungen bis 99°C möglich / With other seals up to 99ºC possible./ Fonctionnement possible jusqu'à 99ºC avec d'autres joints.
3
)
Bestellen Sie zu jedem Pumpenkopf 2 Schlauchnippel (für Schläuche mit ID 6.4 mm - separat bestellen). / Each pump head requires 2 tubing adaptors (for tubing ID 6.4 mm
[1/4“] - order separately. / Chaque tête de pompe a besoin de deux raccords (pour tubes avec d.i. 6.4 mm - commander séparément).
4
)
Der Service Kit beinhaltet sämtliche Teile, falls die Zahnräder oder die Dichtung(en) ausgewechselt werden müssen / The service kit provides all spare parts in case that gears
and seals require replacement / Le
kit d'entretien
contient tous les pièces d’usure pour un échange des douilles, joints ou engrenages.
5
)
Der MCP-Z Process Antrieb wird mit passendem Magnet geliefert. Diese Artikel-Nr. stehen nur für Ersatz-Magnete. / The MCP-Z Process drive is supplied with the magnet
mounted. These part numbers are just for spare magnets / Vous recevez la pompe MCP-Z Process avec l’aimant correspondant. Les numéros indiqués sont pour un remplace-
ment.
Mit Zahnradpumpen dürfen keine partikelhaltige Medien gepumpt werden! / Never use a gear pump system for media containing solids! / Ne pas pomper de liquides contenant des particules!
120 130 Z-140 140 P 140 HC 142 142 HC 150 150 WI
MI 0013 MI 0019 MI 0016 MI 0313 MI 0284 MI 0018 MI 0311 MI 0020 MI 0265
3840 3840 3840 3840 3840 5640 5640 3840 3840
38 38 38 38 38 56 56 38 38
3.5 5.2 3.5 5.6 3.5 3.5 3.5 5.2 5.2
50.8 75.4 50.8 81.2 50.8 50.8 50.8 75.4 75.4
PTFE PPS PTFE PEEK PTFE PTFE PTFE PPS Nickel-Carbid
PTFE PTFE PTFE PTFE PTFE PTFE PTFE PTFE PTFE
**) Hastelloy **) Hastelloy
***) Oberfläche
SS316 SS316 SS316 SS316 C276 SS316 C276 SS316
Surface hardened
21 21 21 21 21 21 21 21 21
304.6 304.6 304.6 304.6 304.6 304.6 304.6 304.6 304.6
-46...+54 -46...+54 -46...+54 -46...+54 -46...+54 -46...+54 -46...+54 -46...+54 -46...+54
-50...+129 -50...+129 -50...+129 -50...+129 -50...+129 -50...+129 -50...+129 -50...+129 -50...+129
✔
✔
– – – – – – –
1/8“–27NPT 1/8“–27NPT 1/8“–27NPT 1/8“–27NPT 1/8“–27NPT 1/8“–27NPT 1/8“–27NPT 1/8“–27NPT 1/8“–27NPT
AR 0001 AR 0001 AR 0001 AR 0001 AR 0001-HC AR 0001 AR 0001-CH AR 0001 AR 0001
AR 0002 AR 0002 AR 0002 AR 0002 - AR 0002 - AR 0002 AR 0002
AR 0008 AR 0008 AR 0008 AR 0008 - AR 0008 - AR 0008 AR 0008
MI 0041 MI 0182 MI 0041 MI 0321 MI 0318 MI 0043 MI 0319 MI 0182 -
MI 0138 MI 0138 MI 0138 MI 0138 MI 0138 MI 0138 MI 0138 MI 0138 MI 0138
Cavity Style / à cavité
i. Ø / i.d. / d.i. - 6 mm
3
)
- 3 mm
3
)
*)
Information Bypass:
**) für korrosive Medien ***) für abrasive Medien
siehe Seite 31 / see page 31 / voir page 31
For corrosive media / Pour milieux corrosifs For abrasive media / Pour milieux abrasifs
Pumpenkopf-Spezifikationen siehe Seite 47 / Pump head specifications see page 47 / Specifications de la tête de pompe, c.f. page 47
- 8 mm
3
)
Zubehör / Accessories / Accessoires
Schlauchnippel /Tubing adaptors / Raccord de tube
Pumpenköpfe / Pump heads / Têtes de pompe