In the Box Inside your Socket box, you will find: 1 iDevices® Socket 1 Quick Start Guide System Requirements iPhone® 4s and later iPad® 3rd generation and later iPad mini™ and later iPod touch® 5th generation and later HomeKit™ requires an iPhone, iPad, or iPod touch with iOS 8.1 or later Wi-Fi® 2.4Ghz 802.11 b/g/n compatible network Router Security Settings Supported: WPA, WPA2, or None iDevices® Connected app version 2.
Getting Started Unit Setup Remove the Socket from packaging. Note 8 digit pin located on the label and on the Quick Start Guide. Screw in your Socket and turn on the power to the socket Please note that the power to the Socket must always be on. The Socket will blink blue indicating it is ready to be set up on the network. A bulb can be screwed in at any time. By default the Socket sets the bulb to full brightness.
Pressing the button on the side of the unit will turn the Socket on or off. Bulb Dimming and control of the LED ring is performed in the iDevices Connected App. iDevices® Connected App Ensure your iOS device’s Wi-Fi® is turned on and is connected to your home Wi-Fi® Network. • 2.4 GHz b/g/n networks are compatible. • 5 GHz networks are not compatible. Download the free iDevices Connected app from the Apple App Store. Connecting Your Socket Available devices will be shown at the top of the app.
In the app, find the Socket you’d like to connect to and tap the add icon. Confirm your home network. The Socket will quickly flash green then turn solid blue to indicate it has successfully joined your home network. If this is your first HomeKit™ product, the app will walk you through creating a home and a room. If you already have a home set up, the app will skip this step. To ensure the app is adding the correct product, the app will ask you to confirm its identity.
Using The Product Once the Socket is set up, you can control the color of the LED light from the iDevices Connected App, or choose to turn the LED light off. Pressing the button on the side of the unit will manually turn the Socket on or off. Problem Solving The following information covers some of the most common troubleshooting issues with the iDevices® Socket. If you’d like more detail about your Socket and its capabilities, please visit our support site at idevicesinc.
Socket Doesn't Show Up in the iDevices App If your Socket doesn't show up after it has successfully been added to your network, make sure you have the following settings enabled: Go to Settings > iDevices. Make sure everything in turned ON. If Home Data was turned off, turn it on. Cycle your WiFi off, then on again. Go to Settings > iCloud.
MODE DESCRIPTION Pairing Mode The accessory is waiting for the handset to configure the accessory’ Wi-Fi®. The LEDs flash blue. Pairing The Socket is waiting for the iOS device to initiate and complete pa set up through Wi-Fi®.The LED is solid blue. Pairing Expired Pairing mode has expired and the accessory is waiting for the user t press the button for about 3 seconds to reenter pairing mode. The LEDs slow flash blue.
MODE DESCRIPTION information, hold the button down for 10 seconds until the LEDs rapidly flash red. When the button is released the unit will reboot an reenter the pairing mode. Identify When the accessory receives a request to identify itself, it rapidly flashes purple. Rating Information UL Rated to UL STD 496, CSA C22.2 No 43-08 Listing: E470483 Input: 125VAC, 60 Hz Output: 125VAC, 60 Hz Max: 60W For use in dry, indoor locations only.
and knowledge, unless they have been given supervision or instruction. Children should be supervised and instructed not to play with this product. Regulations Product Information: Manufacturer: iDevices® LLC Model: IDEV0002 FCC ID: 2ABDJ-SOCKET IC: 11569A- SOCKET FCC Compliance Statement: This device complies with part 15 of the FCC Rules.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
This device complies with Industry Canada license-exempt RSS Standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s).
References Requires the iDevices® Connected app. For warranty information please visit iDevicesinc.com/warranty Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App store is a service mark of Apple Inc. HomeKit is a trademark of Apple Inc.
