I N S TA L L AT I O N & S E T U P G U I D E iDEVICES SMART HOME SOLUTIONS 1
REQUIRES • Wi-Fi® 2.4 GHz 802.11 b/g/n Compatible Network • Router Security Settings Supported: WPA, WPA2, Or None • Free iDevices® Connected App • 120VAC “Line” (usually black, blue or red) And “Neutral”(usually white) Wires • Controlling this HomeKit-enabled accessory requires an iPhone, iPad, or iPod touch with iOS 8.1 or later • Android™ 4.3+ Device With Bluetooth® Smart Technology NOTE: 5 GHz networks are not compatible.
• Not intended for critical medical or life support equipment. • Use caution when using the iDevices® Wall Outlet to control any appliances which produce heat or mechanical motion, or could create a hazardous condition when operated while unattended. • The iDevices® Wall Outlet is not user-serviceable. Do not attempt to open the enclosure for any reason. • The iDevices® Wall Outlet must be installed in a manner that conforms to all applicable national, state, and local building codes.
B E F O R E Y O U S TA RT • Read through this Installation Guide in its entirety before starting installation of your iDevices® Wall Outlet or removal of your old outlet. Incorrect installation can be dangerous and can damage your iDevices® Wall Outlet or your home. • Visit our YouTube channel for tips on installation and setup: www.YouTube.com/User/iDevicesInc • Turn OFF the power to the circuit you are working on at your home’s breaker or fuse panel.
• Wherever possible, install the iDevices® Wall Outlet in a non- metallic gang box and use a non-metallic faceplate, as metal gang boxes and faceplates can decrease the Wi-Fi® signal strength. • Check that your mobile device is compatible with the iDevices® Wall Outlet at iDevicesinc.com/Compatibility • It is YOUR responsibility to be sure that products are installed in accordance with applicable building codes. Check with your local building office if you have questions.
GETTING TO KNOW THE i D E V I C E S ® WA L L O U T L E T 1 6 Top Outlet ON/OFF. Pressing this button will turn the individual outlet ON or OFF. DEVICE RESET: Press and hold for 10 seconds until LED blinks red. PAIRING MODE: Press and hold for 3 seconds until LED is solid blue. 2 Bottom Outlet ON/OFF. Pressing this button will turn the individual outlet ON or OFF. DEVICE RESET: Press and hold for 10 seconds until LED blinks red. PAIRING MODE: Press and hold for 3 seconds until LED is solid blue.
4 5 Pull Out Tab. Refer to this when prompted to enter your HomeKit™ code during the setup on a iOS device. Device Reboot. Pressing this cycles power to the entire unit.
I N S TA L L AT I O N STEP 1 Take a photo of your existing wiring for future reference. Turn OFF the power to the circuit at your breaker or fuse panel. If you are replacing an existing outlet, verify that the outlet no longer has power before proceeding.* STEP 2 Wire the receptacle in place of an existing receptacle according to the adjacent diagram with the provided wire nuts. Ensure the wire nuts are fastened securely.
NEUTRAL (WHITE) NEUTRAL (USUALLY WHITE) LINE (BLACK) LINE (USUALLY BLACK) GROUND (BARE COPPER) GROUND (USUALLY BARE COPPER OR GREEN) 9
STEP 3 Secure the iDevices® Wall Outlet back into the gang box. STEP 4 Turn the power back ON at the breaker. If the outlet is connected properly, you should see the LED indicator rapidly flash blue to indicate the unit is ready to connect to the app.
LED will rapidly flash blue when it’s ready to connect to the app.
CONNECTING TO YOUR NETWORK 1 iDEVICES® CONNECTED APP Download the iDevices® Connected app and connect to your home’s Wi-Fi® network. To proceed with setup please be sure both Wi-Fi® and Bluetooth® are enabled on your device.
2 POWER ON OUTLET Ensure the power/breaker is turned back ON and the LED on the iDevices® Wall Outlet is rapidly flashing blue. Note: If the LED is not flashing blue rapidly, hold either of the ON/ OFF buttons until the LED blinks red, then release to perform a device reset and re-enter pairing mode. At this point, the LED will rapidly flash blue. LED will rapidly flash blue when it’s ready to be paired.
CONNECT OUTLET Launch the iDevices® Connected app and you will be guided through the process of connecting your Wall Outlet. For iOS devices you will need the HomeKit™ setup code, located on the pull out tab. Connected App Icon Basic One Color Optimized Small Versions 14 .75pt Additional .
HomeKit™ setup code is located on the pull out tab of the iDevices® Wall Outlet.
R E F E R E N C E I N F O R M AT I O N LED COLOR CODES LED State Description Blue Flash Wall Outlet is waiting for the handset to configure the accessory’s Wi-Fi®. The LED flashes blue. Solid Blue Wall Outlet is waiting for the mobile device to initiate and complete pair set up. The LED is solid blue. Note: Pairing mode expires after 30 minutes; to reinitiate pairing mode, hold either ON/OFF button down for 3 seconds and the LED will turn solid blue again.
LED State Description Orange Flash When Wall Outlet has lost the connection to the Wi-Fi® network, (e.g., the link is down) the LED slow flashes orange until the link is up. Red Flash To initiate a device reset, which will clear all Wi-Fi® and pairing information, hold either ON/OFF button down for 10 seconds until the LED rapidly flashes red. When the button is released the unit will reboot and re-enter the pairing mode.
S U P P O RT If at any time you require assistance, please contact our Customer Experience Team. Call: 888.313.7019 Email: Support@iDevicesinc.com Visit: iDevicesinc.com/Support T R O U B L E S H O O T I N G A N D S U P P O RT A DEVICE RESET CAN RESOLVE MOST ISSUES. Reset your Wall Outlet by holding either ON/OFF button down until the LED rapidly flashes red.
R E G U L AT O RY I N F O R M AT I O N Product Information: Manufacturer: iDevices LLC Model: IDEV0010 FCC: 2ABDJ-OUTLET IC: 11569A-OUTLET The iDevices® Wall Outlet IDEV0010 is certified to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions. This device complies with Part 15 of the FCC Rules.
FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications.
• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician to help. • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IC Notice This Class B digital apparatus complies with Canadian ICES-003.
This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. References Requires the iDevices® Connected app. For warranty information please visit iDevicesinc.
Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. HomeKit is a trademark of Apple Inc. Controlling HomeKitenabled accessories away from home requires an Apple TV (3rd generation or later) with Apple TV software 7.0 or later and an iPhone, iPad, or iPod touch with iOS 8.1 or later. Amazon, Echo, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
iDevicesinc.
