ILR 350 Series Installation and Operation Manual for Tag i-Q350 RTLS
Installation and Operation Manual Proprietary Notice This document contains confidential information proprietary to IDENTEC SOLUTIONS and may not be used or disclosed to other parties in whole or in part without prior written authorization from IDENTEC SOLUTIONS.
i-Q350 RTLS Tag Manual Radio Frequency Compliance Statement IDENTEC SOLUTIONS is the responsible party for the compliance of the following devices: MODELS: Region/Country EUROPE: USA Canada i-Q350 RTLS Organization EC FCC Industry Canada Marking CE FFC ID OO4-ILR-IQ350RT IC:3538A-IQ350RT The user(s) of these products are cautioned to only use accessories and peripherals approved, in advance, by IDENTEC SOLUTIONS.
Installation and Operation Manual Contents 1 INTRODUCTION ........................................................................................................... 5 1.1 1.2 1.3 1.4 1.5 1.6 PREPARATIONS .............................................................................................................. 5 RECOMMENDED PROCEDURE ............................................................................................. 5 SCOPE OF THIS DOCUMENT ..................................................
i-Q350 RTLS Tag Manual 1 1.1 Introduction Preparations This installation manual must be read carefully prior to starting the installation. The described installation works assume that installation materials like cable, antenna and tag holder etc are available. 1.2 Recommended Procedure 1. 2. 3. 4. Check the Scope of Delivery according to the Bill of Delivery Read this manual completely Mount the tags An additional performance check of the tags and a system test can now be done 1.
Installation and Operation Manual 2 Safety Precautions Important Safety Note The devices described in this manual is for exclusive operation by trained employees. Only qualified personnel that know the potential dangers involved should perform the installation, settings, maintenance and repair of the units used.
i-Q350 RTLS Tag Manual 3 3.1 Tag Mounting Techniques Cable Straps The Tag can be mounted either with cable straps using the 2 slits at each end or using rivets or screws as described in the following 2 subchapters.
Installation and Operation Manual 3.2 Rivets 3/16” dia. blind rivet (M5) Important Information 1. 2. 3. 4. 5. A temperature of at least +10 °C (+50 °F) must be maintained during riveting to prevent the casing from cracking. Always position the blind-rivet gun straight down on the rivet site and all the way to the rivet socket. On occasion, a tag casing has been damaged through improper handling of the blind-rivet gun (slanted positioning of the gun to access the rivet socket).
i-Q350 RTLS Tag Manual 3.3 Screws i.e. #10 cylinder head or lenticular head screws i.e. 3/16” hexagonal locknut with 3/16” washer OR 3/16” hexagonal nut, but together with spring washer or 3/16” Nordlock washer Important Information 1. 2. 3. 4. 5. 6. 7. Only screws with cylindrical heads are suitable for mounting the tag. We do not advise using countersunk screws. If for some reason this should be necessary, then only together with a suitable counter-sunk cushioning disc (refer to UN 1277).
Installation and Operation Manual Page 10 of 15
i-Q350 RTLS Tag Manual 4 4.1 Initial Operation Configuration of The Tag Important Note Do not open the housing! Configuration is done using the built-in air interface of the i-Q350 RTLS. Configuration The i-Q350 RTLS is configured according to the specific application by the custom-specific host software. Things to be configured • The ping rate: from 0.5 to 300 seconds in steps of 0.
Installation and Operation Manual 5 5.1 Maintenance General In principle, the ILR system is maintenance-free. When correctly installed it operates for many years without any problems. 5.2 Battery Exchange Important Note Replace battery only with the same type SL-760 S. Remove the lower end cap with a Phillips screw driver . The lower end cap/battery lid is on the side close to the push button. Furthermore there is a battery symbol on the rear side of the tag housing.
i-Q350 RTLS Tag Manual 5.3 Precautionary Maintenance Regular checking of all ports and cables belonging to the system is recommended. Unstable connections could lead to damage and malfunctions of the system and therefore should be repaired as soon as possible. A Brief Checklist • Are all housings intact? • Are all cables intact? • Are all connectors intact? • Are all connectors securely fastened? • Are all screws still tight? • Is there suddenly a malfunction at a specific unit? 5.
Installation and Operation Manual 6 Technical Data Operating Data Long-Range RFID (ILR, 2400 – 2485 MHz ISM Band) Read/write/localization range Channels Data rate Maximum transmission power Standards/Certification Compatibility Up to 180 m (590 ft) in free air with line of sight 3 Non-Overlapping channels (for EU and US) or 7 Overlapping channels 250 Kbits/s and 1 Mbits/s 100 mW EIRP or local regulation ISO 24730 part 5 (upcoming standard), FCC part 15, EN 300 328 (EU) i-PORT M-350 RTLS, i-SAT 300 Oper
i-Q350 RTLS Tag Manual Dimensional Drawing All dimensions in mm.
