IDENTEC SOLUTIONS Model IDS1001 iPOINT Si HARDWARE USER MANUAL
iPOINT – Hardware User Manual | 18.06.2020 Proprietary Notice This document contains confidential information proprietary to IDENTEC SOLUTIONS and may not be used or disclosed to other parties in whole or in part without the prior written authorization from IDENTEC SOLUTIONS.
iPOINT – Hardware User Manual | 18.06.2020 Radio Frequency Compliance Statement IDENTEC SOLUTIONS is the responsible party for the compliance of the following devices: MODEL: IDS1001 iPOINT Si Region/Country Organization Marking EUROPE: EU CE USA: FCC FCC ID OO4-IDS1001 CANADA: IC 3538A-IDS1001 The user(s) of these products are cautioned to only use accessories and peripherals approved, in advance, by IDENTEC SOLUTIONS.
iPOINT – Hardware User Manual | 18.06.2020 WARNING - This product should be installed by personnel trained in installation of equipment in industrial environments and meet the representative country’s National Electrical Code. Electrostatic Discharge This product contains components that are sensitive to electrostatic discharges. Please observe the special instructions for their protection. Incorrect handling can damage the unit and cause the invalidation of the warranty.
iPOINT – Hardware User Manual | 18.06.2020 Safety Instructions The equipment can be installed in restricted areas. The system described in this manual is for exclusive operation of trained employees. Only qualified personnel that have knowledge of the potential dangers involved should perform the installation, settings, maintenance and repair of the units used.
iPOINT – Hardware User Manual | 18.06.2020 Contents 1. Preface .................................................................................................................................................................... 7 2. Introduction .............................................................................................................................................................. 8 2.1 iPOINT and System Description ......................................................................
iPOINT – Hardware User Manual | 18.06.2020 1. Preface This installation manual must be read carefully prior to starting the installation. The described installation works assuming that installation materials like cables, antennas and any mechanical parts are available. This document is the hardware description of the iPOINT. This document is intended only for mechanical and electrical installation of these central units.
iPOINT – Hardware User Manual | 18.06.2020 2. Introduction 2.1 iPOINT and System Description The iPOINT device provides a functional combination of: The “zone location” system of an i-MARK, the long-range Reader functionality of an i-PORT as well as close proximity NFC functionality, encased in an attractive, rugged, IP67 housing. The Housing contains: - 5 Status LEDs (see Section 3.
iPOINT – Hardware User Manual | 18.06.2020 2.1.1 UHF Interface The UHF interface is a wireless communication interface using the UHF ISM frequency band and IDENTEC’s protocols. The iPOINT X has two internal UHF antennas built in and can communicate up to a range of 500 meters with its Tags. The main benefit of two antennas is the elimination of RF dead spots in static systems. 2.1.2 LF Interface The LF Interface uses IDENTEC’s LFBOOST Marker technology.
iPOINT – Hardware User Manual | 18.06.2020 2.1.3 NFC Interface The NFC Interface is a Near Field Communication interface. The iPOINT can be used as an entry terminal or for other NFC communication. The range to the Tag is around 10-15cm and is compatible with the i-Q355 Series of Tags as well as standard NFC cards. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
iPOINT – Hardware User Manual | 18.06.2020 2.2 System Components – Tags Identec offers a wide range of tags that can be used with the iPOINT. The tags provide long range communication with the readers of up to 500 m (1640 ft), using advanced UHF radio frequency technology. i-Q355 Tags Using advanced UHF radio frequency technology, i-Q355 tags transmit and receive data at distances of up to 250 m (820 feet).
iPOINT – Hardware User Manual | 18.06.2020 2.3 Ports Overview & Topologies PoE RJ45 PoE cable connector to the host computer or switch USB USB Mini connector for debugging, low power operation and device configuration RS422 MASTER RS422 SLAVE RJ45 RS422 cable connector to the host computer or previous Slave port in the daisychain RJ45 RS422 cable connector to the master port of the next i-PORT in the daisy chain. Leave this connector open at the last device in the chain.
iPOINT – Hardware User Manual | 18.06.2020 RS422 with injected 24V Power installation: - Make sure power supply can handle all iPOINTs in the system USB Mode (5V) - Local USB mode over Mini-USB Connector for debugging, low-power operation and Configuration No Slave mode under USB operation - Maximum power consumption of an iPOINT is 7W. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
iPOINT – Hardware User Manual | 18.06.2020 2.3.1 PoE Connector & Pinout PoE interface: Shielded wire connection with PoE voltage, according to the Standard. RJ45 Plug. View into the connector = crimp/solder side of plug Pin 2.3.
iPOINT – Hardware User Manual | 18.06.
iPOINT – Hardware User Manual | 18.06.2020 2.4 USB Only mode – Function and specification 2.5 The iPOINT Device can be used with a single connection over the Mini USB port. During this operation, 5V is supplied and powers the device. This can be a fast way to access the device in the field for configuration purposes.
iPOINT – Hardware User Manual | 18.06.2020 3. Initial Operation / Configuration The configuration of the iPOINT is managed via the host software. Available Identec Solutions Software Setup Scout i-Share Crew Companion Please refer to the relevant software User Manuals for details. 3.1 Status LEDs UHF This is the UHF Communication LED. LED blinks green when a valid command has been sent to Tag. It blinks Orange when a response or a broadcast is received. LF This is the LF Communication LED.
iPOINT – Hardware User Manual | 18.06.2020 4. Mechanical Information & Installation Housing Dimensions 4.1 Opening the connection Chamber 1. 2. 3. 4. Lift up the cover using thumbs from the front side until magnetic connection is released, lift off. Loosen the 8x screws, be aware, DO NOT pull out the screws out completely, the gasket can be damaged. Lift off the lid. Now you have access to the Connection Chamber Note: when replacing the lid, be sure that the sealing gasket is correctly in place.
iPOINT – Hardware User Manual | 18.06.2020 4.2 Mounting Options The mounting plate can be attached to a wall, pole mount bracket, extension bracket or DIN rail. There are 4 fixing holes for attaching the relevant bracket or screwing to a wall. For mounting with a pole mount bracket or extension bracket, please see relevant Installation guides provided with the kits. For Direct wall mounting, using the mounting plate only, 4x countersunk screws are required with a maximum diameter of 5mm or M5 screws.
iPOINT – Hardware User Manual | 18.06.2020 Warning: when unmounting device from the mounting plate, first lift the device up, then out; do not pull device directly or there’s a risk of damage. 4.2.1 Optional Extra: Pole Mount Bracket Kit A Pole Mount Bracket Kit is available. - Pole Mount Bracket Kit: o Contains the bracket and accessories o The bracket can be mounted to a wall with M8 Bolts or via threaded rods (e.g.
iPOINT – Hardware User Manual | 18.06.2020 4.2.2 Optional Extra: Extension Bracket Kit An Extension Bracket Kit is available - Extension Bracket Kit: o Contains the bracket and accessories o The bracket can be mounted to a wall with M8 Bolts or via threaded rods (e.g. wall anchors) o Multiple mounting options, including use of the pole mount bracket o Refer to “Extension Bracket Kit – Quick Installation Guide” documentation for more details. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
iPOINT – Hardware User Manual | 18.06.2020 Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
iPOINT – Hardware User Manual | 18.06.2020 5. Troubleshooting This chapter covers how faults can be recognized and rectified. There are potentially four main problem sources: The user control system, including task requirements, communication cables, peripheral units with possible object recognition switches. The Crew Companion platform including peripheral units and their cables, also potential object recognition switches.
iPOINT – Hardware User Manual | 18.06.2020 6.2 Firmware Update The firmware is stored in a FLASH memory and can be updated if needed. 6.3 Spare Parts Recommended spare parts stock In order to minimize the downtime in the event of a malfunction, it is recommended to have certain spare parts on stock. For larger systems with more than 15 iPOINTs, doubling of the recommended stock quantity is recommended. Furthermore, it is advised to have several spare ILR® Tags in stock, corresponding to approx. 0.
iPOINT – Hardware User Manual | 18.06.2020 7.
iPOINT – Hardware User Manual | 18.06.2020 Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
