Datasheet

PS6R Switching Power Supplies
Safety Precautions
Operating Instructions
Notes for Installation
•The PS6R can be installed in the direction shown below only.
Vertical When using PS9Z-6R1F
Panel Mounting Bracket
When using PS9Z-6R2F
Side-mount Panel Mounting
Bracket
Up
•Do not close the top and bottom openings of the PS6R to al-
low for heat radiation by convection.
•Maintain a minimum of 20 mm clearance around the PS6R,
except for the top and bottom openings.
•When derating of the output does not work, provide forced air-
cooling.
•Make sure to wire the ground terminal correctly.
•For wiring, use wires with heat resistance of 60°C or higher.
Use copper wire of the following sizes. Wires of the follow-
ing size must be used to comply with UL508, CSA C22.2 No.
107.1.
Model Terminal Wire Size/No. of Wire Wire Type
Torque,
in-ibs (Nm)
PS6R-F24
PS6R-G24
Input
18-14 AWG, 1-wire
Copper
Solid/
Stranded
7.0 (0.8)
Output
18-14 AWG, 1-wire,
(18 AWG - 7A, 16 AWG - 10A,
14 AWG - 15A)
DC OK
Output
22-14 AWG, 1-wire
(stripped wire length: 6 to 7mm)
PS6R-J24
Input
18-14 AWG, 1-wire
Output
18-14 AWG, 1-wire, 2-wire
Use the wire of the same size
for each terminal (18 AWG - 7A,
16 AWG - 10A, 14 AWG - 15A)
12 AWG, 1-wire
Copper
Solid/
Stranded
Use with
UL-listed ring/
folk crimp
terminal.
DC OK
Output
22-14 AWG, 1-wire
(stripped wire length: 6 to 7mm)
Copper
Solid/
Stranded
—
PS9Z-6R*
Output
18-14 AWG, 1-wire
(18 AWG - 7A, 16 AWG -10A,
14 AWG - 15A)
7.0 (0.8)
Applicable Crimp Terminal (reference)
6.6 max.
ø3.6 min.
5.5 min.4 max.
•Recommended tightening torque of the input and output termi-
nals is 0.8 N·m.
•The output voltage can be adjusted within ±10% of the rated
output voltage by using the V.ADJ control. Note that overvolt-
age protection may work when increasing the output voltage.
•When large shocks or heavy vibrations on the PS6R are ex-
pected, the use of DIN rail or PS9Z-6R2F side-mount panel
mounting bracket is recommended.
Mounting on DIN Rails
•Fasten the DIN rail to a mounting plate using screws.
•When mounting the PS6R on a DIN rail, place the PS6R as
shown. With the clamp inserted, press the PS6R towards the
DIN rail.
•Use end clips BNL6 for fastening the PS6R on the DIN rail.
When using with a PS9Z-6RM
DC-DC converter unit, install
the BNL6 on the left side of the PS6R first.
Mounting
Removal
LOCKED
UNLOCKED
Latch Status
Removal
•Insert a flat screwdriver into the slot in the clamp, and pull
out the clamp until it clicks. Turn the PS6R bottom out. When
mounting the PS6R again, push in the latch first.
Mount the PS6R in an enclosure. Do not use the PS6R
alone as an Electric Facilities for General Use.
Use the PS6R for electric facilities for business use only.
•Do not use switching power supplies with electric equipment
whose malfunction or inadvertent operation may damage the hu-
man body or life directly.
•Make sure that the input voltage and output current do not exceed
the ratings. If the input voltage and output current exceed the rat-
ings, electric shock, fire, or malfunction may occur.
•Do not touch the terminals of the switching power supply while
input voltage is applied, otherwise electric shock may occur.
•Provide the final product with protection against malfunction or
damage that may be caused by malfunction of the switching pow-
er supply.
•Operating temperatures should not exceed the ratings. Be sure
to note the derating characteristics. If the operating temperature
exceeds the ratings, electric shock, fire, or malfunction may occur.
•Blown fuses indicate that the internal circuits are damaged. Con-
tact IDEC for repair. Do not just replace the fuse and reoperate,
otherwise electric shock, fire, or malfunction may occur.
•Do not use the switching power supplies to charge rechargeable
batteries.
•Do not overload or short-circuit the switching power supply for a
long period of time, otherwise the internal elements may be dam-
aged.
•Do not disassemble, repair, or modify the power supplies, other-
wise the high voltage internal part may cause electric shock, fire,
or malfunction.
•The fuse inside the PS6R switching power supply is for AC input.
Use DC fuse for DC input.
10
(13/11/08)