Datasheet

Safety Precautions
IDEC CORPORATION (USA)
1175 Elko Drive, Sunnyvale, CA 94089-2209, USA
Tel: [phone] / (800) 262-IDEC (4332)
Fax: [phone]
E-mail: [e-mail]
IDEC CANADA LIMITED
3155 Pepper Mill Court, Unit 4, Mississauga,
Ontario, L5L 4X7, Canada
Tel: [phone], Toll Free: [phone]
Fax: [phone]
E-mail: [e-mail]
IDEC AUSTRALIA PTY. LTD.
2/3 Macro Court, Rowville, Victoria 3178, Australia
Tel: [phone], Toll Free: 1800-68-4332
Fax: [phone]
E-mail: [e-mail]
IDEC ELECTRONICS LIMITED
Unit 2, Beechwood, Chineham Business Park,
Basingstoke, Hampshire RG24 8WA, UK
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
Specifications and other descriptions in this catalog are subject to change without notice.
Cat. No. EP1307-0 JUNE 2010 PDF
IDEC ELEKTROTECHNIK GmbH
Wendenstrasse 331, 20537 Hamburg, Germany
Tel: [phone] - 0, Fax: [phone] - 24
E-mail: [e-mail]
IDEC (SHANGHAI) CORPORATION
Room 608-609, 6F, Gangtai Plaza, No. 700,
Yan'an East Road, Shanghai 200001, PRC
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC (BEIJING) CORPORATION
Room 211B, Tower B, The Grand Pacific Building,
8A Guanghua Road, Chaoyang District,
Beijing 100026, PRC
Tel: [phone], Fax: [phone]
IDEC (SHENZHEN) CORPORATION
Unit AB-3B2, Tian Xiang Building, Tian’an Cyber Park,
Fu Tian District, Shenzhen, Guang Dong 518040, PRC
Tel: [phone], Fax: [phone]
IDEC IZUMI (H.K.) CO., LTD.
Units 11-15, Level 27, Tower 1,
Millennium City 1, 388 Kwun Tong Road,
Kwun Tong, Kowloon, Hong Kong
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC TAIWAN CORPORATION
8F-1, No. 79, Hsin Tai Wu Road, Sec. 1,
Hsi-Chih, Taipei County, Taiwan
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC IZUMI ASIA PTE. LTD.
No. 31, Tannery Lane #05-01,
HB Centre 2, Singapore 347788
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
www.idec.com
Instructions
Before designing nal equipment and powering up illumination •
units, conrm the specications described on the instruction
sheet. If there is any uncertainty, contact IDEC before
powering up illumination units.
Apply voltage within the rated value, otherwise the LED •
elements may be damaged.
The illumination unit is vulnerable to static electricity. Take •
sufcient measure for protection against static electricity and
voltage surges.
Make sure that the illumination unit does not fall during •
transportation, installation, and operation, otherwise damage
may result.
Do not pull or push the cable of the illumination unit, otherwise •
damage may result. Allow sufcient slack to the cable while
wiring.
Do not apply excessive force to the illumination unit. Do •
not leave a damaged illumination unit unattended or use a
damaged illumination unit.
Ensure the correct operating temperature around the •
illumination unit. Otherwise internal temperature rise may
result in damage.
Do not use or store the illumination unit in a place subjected to •
vibration and shock.
Do not use the illumination unit in the following places:•
∗ Exposed to direct sunlight, near heaters, and at high tem-
peratures
∗ Subject to chemicals, and corrosive gases (Plastic illumina-
tion surface types: Iron powder and oil)
∗ Basements, greenhouses, or other humid places
∗ Cold storage warehouses and cooler exhaust outlets (make
sure that no freezing occurs)
Do not loosen screws, otherwise the protection characteristics •
will be impaired.
For the LF2D illumination units, make sure to a provide •
sufcient strength for mounting panel. Required waterproof
characteristics cannot be obtained if a distorted mounting
panel is used.
Use illumination units with a Class 2 power supply.•
Do not disassemble, repair, or modify illumination units. •
Otherwise electric shock, re, or malfunction may occur.
Turn off power to the illumination units before wiring. Make •
sure of correct wiring, otherwise electric shock or damage
may result.
Do not stare directly into the illumination unit while it is lit, and •
do not project the light to other people, otherwise eyes may
be injured.
The illumination unit is a general-purpose industrial electric •
device. Do not use the illumination unit for electronic
equipment which may damage the human body or threaten
life in case a malfunction or failure occurs.
LF1D/LF2D LED Illumination Units
TM
(100611)