Datasheet

201
800-262-IDEC (4332) • USA & Canada
SA1C-F
Sensors
OI Touchscreens PLCs Automation Software Power Supplies Sensors Communication Barriers
Specifications
SA1C-FN, -FD
(Standard Speed)
SA1C-F1N, -F1D
(High-speed)
General Specifications
Power Voltage 12V to 24V DC √ √
Operating Voltage 10V to 30V DC, ripple 10% (maximum) √ √
Current Draw
30mA (maximum) √ –
40mA (maximum) – √
Operating
Temperature
Amplifier only: –25° to +55°C
Fiber optic cords (except heat-resistant types): –40° to +70°C
Heat-resistant fiber optic cords: –40°C to +350°C
(avoid ice coating)
√ √
Operating Humidity 35 to 85% RH (avoid condensation) √ √
Extraneous Light
Immunity
Sunlight: 10,000 lux (maximum); Incandescent light: 3,000 lux (maximum) on receiver
surface— defined as incident or unwanted light received by a sensor, unrelated to the
presence or absence of the intended object
√ √
Material
Amplifier only: PBT resin (housing) with polycarbonate lens
Fiber optic cords (except heat-resistant types): Nickel-plated brass (sensing head),
polyethylene-covered PMMA (cord), and SUS304 stainless (sleeve)
Heat-resistant fiber optic cords: SUS 304 stainless (sensing head) and SUS spiral tube
around glass fiber cord
√ √
Degree of
Protection
IP66 — IEC Pub 529, sensors rated IP66 are dust-tight, water-resistant, and perform best
when not subjected to heavy particle or water blasts
√ √
Connection
Cable type: 0.2mm
2
; Vinyl cabtyre cable #24 AWG, 6’–6-3/4’ (2m) long
Connector type: Ø 0.31” (8mm) 3- or 4-pin connector
(cable ordered separately for quick connect sensors)
√ √
Light Source Red or green LED (pulse-modulated) √ √
Output
NPN transistor: 30V DC (1.2V residual), 100mA (maximum)
PNP transistor: 30V DC (2.0V residual), 200mA (maximum)
Self-diagnostic: 30V DC (1.2V residual), 50mA (maximum)
√ √
Response
0.5ms (maximum) √ –
50µs (maximum) – √
Off Delay 0 to 100 ms (adjustable) √ √
Sensitivity 4-turn adjustment √ √
Minimum
Bending Radius
Fiber optic cord (except SA9F-TT, -DT, -TL, and -DL): 1”R (25mm); Sleeve: 0.39”R (10mm)
SA9F-TT and -DT: 0.59”R (15mm); Sleeve: 0.39”R (10mm)
SA9F-TL and DL: 0.59”R (15mm); Sleeve: Unbendable
√ √
Function Specifications
Operation Mode Light on or dark on (selectable by switch on amplifier) √ √
Indicator
Operation indicator: Red LED (out) √ √
Stable level indicator: Green LED (stable) √ √
Noise
Resistance
Normal Mode
500V √ –
300V – √
Common
Mode
300V √ –
150V – √
Pulse Width 50ns –1µs, 100Hz (using a noise simulator) √ √
Storage Temperature –30 to +70°C (avoid freezing) √ √
Insulation Resistance 20M minimum with 500V DC megger (between live & dead parts) √ √
Dielectric Strength 1000V, 1 minute (between live & dead parts) √ √
Vibration Resistance
Damage limits: 10 – 55Hz
Amplitude: 1.5mm p-p, 20 cycles in each of 3 axes crossed (one cycle = 5
minutes)
√ √
Shock Resistance Damage limits: 500m/s
2
(approximately 49G), 10 shocks in each of 3 axes √ √
Weight
Cable type: Approximately 75g
Quick-connect type: Approximately 30g
√ √