Data Sheet

Download catalogs and CAD from http://apac.idec.com
M-008
APEM
Switches &
Pilot Lights
Control Boxes
Emergency
Stop Switches
Enabling
Switches
Safety Products
Explosion Proof
Terminal Blocks
Relays & Sockets
Circuit
Protectors
Power Supplies
LED Illumination
Controllers
Operator
Interfaces
Sensors
AUTO-ID
Sensors
SA1E
SA1E-L
SA1E Miniature Photoelectric Switches (Built-in Amplier)
Slit and Sensing Range
A slit, which changes the beam size of through-beam sensors, can easily be attached to the sensing side of the through-beam projector and
receiver. Three different slit widths are available.
Slit
w/Sensitivity Adjustment
Sensing Range (m) Minimum Detectable Object Width (mm) (Note 1)
Attached on:
Part No. Slit Width: A (See M-017) Receiver Receiver/Projector Receiver Receiver/Projector
SA9Z-S06 0.5 mm 2.5 1.0 0.5 0.5
SA9Z-S07 1.0 mm 3.5 1.5 1.0 1.0
SA9Z-S08 2.0 mm 6.0 3.5 2.0 2.0
SA9Z-S09 0.5 mm 2.0 0.7 0.5 0.5
SA9Z-S10 1.0 mm 3.0 1.5 1.0 1.0
SA9Z-S11 2.0 mm 5.5 3.0 2.0 2.0
SA9Z-S12 0.5 mm 0.8 0.08 0.5 0.5
SA9Z-S13 1.0 mm 1.5 0.3 1.0 1.0
SA9Z-S14 2.0 mm 2.5 1.2 2.0 2.0
Note 1: At 1mm from receiver surface.
• The slit can be installed onto the front easily (see the gure at right).
+V
OUT
0V
Brown (1)
Black (4)
Load
12V to
24V DC
Blue (3)
Main Circuit
+V
Brown (1)
Load
Black (4)
OUT
12V to
24V DC
0V
Blue (3)
Main Circuit
+V
Brown (1)
Black (4)
Load
OUT
12V to
24V DC
0V
Blue (3)
Main Circuit
+V
Brown (1)
Load
Black (4)
OUT
12V to
24V DC
0V
Blue (3)
Main Circuit
PNP OutputNPN Output
PNP OutputNPN Output
Through-beam Projector
Through-beam Projector
+V
Brown (1)
12V to
24V DC
0V
Blue (3)
Main Circuit
+V
Brown (1)
12V to
24V DC
0V
Blue (3)
Main Circuit
Connector Pin Assignment
➀
(OUT)
➁
(NC)
➂
(0V)
➃
(+V)
Connector Pin Assignment
➀
(OUT)
➁
(NC)
➂
(0V)
➃
(+V)
Connector Pin Assignment
➀
(OUT)
➁
(NC)
➂
(0V)
➃
(+V)
Connector Pin Assignment
➀
(OUT)
➁
(NC)
➂
(0V)
➃
(+V)
➃
(NC)
➁
(NC)
➂
(0V)
➀
(+V)
Connector Pin Assignment
➃
(NC)
➁
(NC)
➂
(0V)
➀
(+V)
Connector Pin Assignment
Coaxial polarized retro-reflective (Transparent Object Sensing)
Slit
(stainless steel)
The slit can be pressed to snap onto the front easily.
Horizontal slits and round slits have an orientation. Make sure that the TOP
marking comes on top of the sensor (LED side).
Output Circuit & Wiring Diagram
Through-beam
Polarized reflective
Diffuse-reflective
Background suppression (BGS)
Small-beam reflective
Download catalogs and CAD from http://eu.idec.com/downloads