Data Sheet
For more information, visit http://apac.idec.com
M-017
APEM
Switches &
Pilot Lights
Control Boxes
Emergency
Stop Switches
Enabling
Switches
Safety Products
Explosion Proof
Terminal Blocks
Relays & Sockets
Circuit
Protectors
Power Supplies
LED Illumination
Controllers
Operator
Interfaces
Sensors
AUTO-ID
Sensors
SA1E
SA1E-L
SA1E Miniature Photoelectric Switches (Built-in Amplier)
Reflector Mounting Brackets
28.1
18.9
27.2
5°
ø4.7
ø10
➃ Black ➁ White
➂ Blue ➀ Brown
Cable length:
2 or 5m
IAC-L2 (for IAC-R5) IAC-L3 (for IAC-R6) IAC-L5 (for IAC-R8)
Connector Cable (connector on one end)
Straight
(SA9Z-CM8K-4S)
Right-angle
(SA9Z-CM8K-4L)
Cable length:
2 or 5m
33.7
ø4.7
ø10
➃ Black ➁ White
➂ Blue ➀ Brown
• Dielectric strength when installed on the SA1E: 1000V AC (between live part
and mounting bracket, except between live part and tightening ring)
Air Blower Mounting Block
SA9Z-A02
5.8
14.0
8.0
37.0
25.4
25.0
6.9
M5
P0.8
M5
P0.8
42.5
14.0
6.5
31.5
8.0
3.4
10.9
(3.8)
2.03.5 19.5
Plugging screws
for air supply port
(M5), Gasket
(used on one
side only)
Air supply port
Air Blower
Mounting Block
SA1E-****
(3.2)
Recommended mounting
bracket (SA9Z-K01)
2-ø3.2
(Material: Anodized aluminum surface)
With Mounting Bracket
• The SA9Z-A02 air blower mounting block is
supplied with two mounting screws (M3 × 20
mm sems screws), one screw for plugging the
air supply port (M5 × 6 mm), and one gasket for
plugging the air supply port.
• An air tube tting (M5) can be installed to either
the top or side. Tighten the tting to a torque of
0.5 N·m maxi mum.
• The air tube tting and mounting bracket are
not supplied and must be ordered separately
(recommended mounting bracket: SA9Z-K01).
Vertical Slit
SA9Z-S06
SA9Z-S07
SA9Z-S08
Horizontal Slit
SA9Z-S09
SA9Z-S10
SA9Z-S11
Round Slit
SA9Z-S12
SA9Z-S13
SA9Z-S14
18
8.2
32.1
A
6.1
0.3
A
8.2
32.1
6.1
0.3
4.4
6.5
øA
4.4
8.2
32.1
6.1
0.3
Material: Stainless Steel
Note: For slit width A, see M-008.
Material: SPCC (zinc chromate plating, black)
42
5.5
19
6
28
37
74
113
2
2-ø3.4
4-ø4.4
30
58
70
60
44
20
1.6
25
Material: SPCC (zinc plating)
8-M3 × 0.5 holes
25
4.5
11
10
35
161086
(3)
40
4.5
10
Material: SPCC (zinc plating)
26
12
35
(28)
(3)
20
(2)
61
1615187
40
50
11
8-M3 × 0.7 holes
Accessory Dimensions All dimensions in mm
For more information, visit http://eu.idec.com