Datasheet

ManualsBrandsIDEC ManualsAutomationRight-Angle Actuator

HS6E Subminiture Interlock Switches with Solenoid

When using the HS9Z-A65/HS9Z-A66 Angle Adjustable

Actuator

•When the door hinge is on the extension line of the interlock

switch surface

•When the door hinge is on the extension line of the actuator

mounting surface

Actuator Angle Adjustment for the HS9Z-A65/HS9Z-A66

• Using the angle adjustment screw, the actuator angle can be

adjusted (see figures on page 17).

Adjustable angle: 0 to 20°

• The larger the adjusted angle of the actuator, the smaller the

applicable radius of the door opening.

• After installing the actuator, open the door. Then adjust the

actuator so that its edge can enter properly into the actuator

entry slot of the interlock switch.

• After adjusting the actuator angle, apply Loctite to the adjust-

ment screw so that the screw will not become loose.

Mounting Examples

Mount the interlock switch on a fixated machine or guard, and

mount the actuator on the hinged door. Do not mount both interlock

switch and actuator on hinged doors, otherwise malfunction will

occur.

Note: When mounting an actuator, make sure

that the actuator enters the slot in the

correct direction, as shown on the right.

For Manual Unlocking

Spring lock

The HS6E allows manual unlocking of the actuator to pre-check

proper door operation before wiring or turning power on, as well as

for emergency use such as a power failure.

Solenoid lock

The HS6E can be unlocked manually in emergency.

When using the manual unlock key

• When locking or unlocking the interlock switch manually, turn

the key fully using the manual unlock key supplied with the

switch.

• Using the interlock switch with the key not fully turned (less

than 90°) may cause damage to the interlock switch or opera-

tion failures (when manually unlocked, the switch will keep the

main circuit disconnected and the door unlocked).

• Do not apply excessive force (0.45 N·m or more) to the

manual unlock part, otherwise the manual unlock part will

become damaged.

• Do not leave the manual unlock key attached to the switch

during operation. This is dangerous because the switch can

always be unlocked while the machine is in operation.

When unlocking pushing the plate inside the interlock switch

• Remove the screw at the side of the interlock switch (the

same side where actuator is inserted) and insert a small

screwdriver.

• Push the plate inside the interlock switch toward the LED indi-

cator using the screwdriver until the actuator is unlocked.

• Tighten the screw to a proper torque (0.3 to 0.5 N·m). Do not

tighten with excessive force, otherwise the interlock switch will

be damaged. Be sure to reinstall the screw, otherwise the

waterproof capability will be lost.

Caution

Before manually unlocking the interlock switch, make sure

that the machine has come to a complete stop. Manual

unlocking during operation may unlock the interlock switch

before the machine stops, and the function of the interlock

switch with solenoid is lost. While the solenoid is energized,

do not unlock the switch manually (solenoid lock).

50 mm

HS9Z-A66

HS9Z-A65

HS9Z-A66

HS9Z-A65

HS9Z-A66

70 mm

HS9Z-A65

HS9Z-A66

70mm

Label

Minimum

Radius

Minimum

Radius

Minimum

Radius

Minimum

Radius

Minimum

Radius

Minimum

Radius

Minimum Radius

Door Hinge

Horizontal Adjustment

Vertical Adjustment

50 mm

HS9Z-A66

HS9Z-A65

HS9Z-A66

HS9Z-A65

HS9Z-A66

70 mm

HS9Z-A65

HS9Z-A66

70mm

Label

Minimum

Radius

Minimum

Radius

Minimum

Radius

Minimum

Radius

Minimum

Radius

Minimum

Radius

Minimum Radius

Door Hinge

Horizontal Adjustment

Vertical Adjustment

HS9Z-A61 Actuator

Door

HS6E

Interlock Switch

Door Stop

Application on Sliding Doors

Application on Hinged Doors

Latch

HS9Z-A62S Actuator

Manual Unlocking

Position

Normal Position

(installed on both sides)

Manual Unlocking

UNLOCK

LOCK

Manual Unlock Key

(supplied with the interlock switch)

Screwdriver

HS6E