Datasheet

ManualsBrandsIDEC ManualsAutomationStraight Actuator with Rubber Bushings - HS5 Series Miniature Interlock Switch

HS5L Interlock Switches with Solenoid

Instructions

Minimum Radius of Hinged Door

When using the interlock switch for a hinged door, refer to the

minimum radius of doors shown below. Especially for doors with

a small turning radius, use vertical/horizontal movable actuators

(HS9Z-A53/A55).

Note: Because deviation or dislocation of a hinged door may occur in actual

applications, make sure of the correct operation by installing the

actual machine rst before use.

HS9Z-A52 Actuator

When the center of the hinged door is used as the reference for

the interlock switch contact surface:

Door Hinge

Interlock Switch

Mounting Hole

190mm

170mm

Minimum Radius

(161)

(35)

(36.2)

When the center of the hinged door is used as the reference for

the actuator mounting surface:

230mm

260mm

(41.5)

(40.3)

(231)

Door Hinge

Interlock S

witch

Mounting Hole

Minimum Radius

HS9Z-A52A Actuator (with Rubber Bushings)

When the center of the hinged door is used as the reference for

the interlock switch contact surface:

Centers 12mm: 120mm

Centers 20mm: 170mm

140mm

(36.2)

(111)

(35)

Door Hinge

Interlock Switch

Mounting Hole

Minimum Radius

When the center of the hinged door is used as the reference for

the actuator mounting surface:

Centers 12mm: 230mm

Centers 20mm: 310mm

260mm

(231)

(47)

(48.2)

Door Hinge

Interlock Switch

Mounting Hole

Minimum Radius

Actuator Angle Adjustment (vertical/horizontal)

• Using the angle adjustment screw, the actuator angle can

be adjusted (refer to the dimensional drawing on page 17).

Adjustable angle: 0 to 20°

• The larger the adjusted angle of the actuator, the smaller the

applicable radius of the door opening. After installing the

actuator, open the door. Then adjust the actuator so that its

edge can be inserted properly into the actuator entry slot of the

interlock switch.

• After adjusting the actuator angle, apply Loctite to the

adjustment screw so that the screw will not move.

When using the HS9Z-A55S Angle Adjustable (vertical/

horizontal) Actuator (w/Plate)

•When the center of the hinged door is used as the reference for the inter-

lock switch contact surface: 50mm

•When the center of the hinged door is used as the reference for the actua-

tor mounting surface: 70mm

•The HS9Z-A55S angle adjustable actuator is made of glass-reinforced

PA66 (66 nylon) and the angle adjustment screw and plate are made of

stainless steel. When using the screw locking agent, make sure that it is

compatible with the base material.

When the center of the hinged door is used as the reference for the interlock

switch contact surface:

(36.2)

(38)

Vertical Swing

Horizontal Swing

Door

Hinge

Door

Hinge

Interlock

Switch

Mounting

Hole

50mm

Minimum Radius

50mm

Minimum Radius

When the center of the hinged door is used as the reference for the actuator

mounting surface:

(56.5)

(58)

Vertical Swing

Horizontal Swing

Door

Hinge

Door

Hinge

Interlock

Switch

Mountin

Hole

70mm

Minimum Radius

70mm

Minimum Radius

When using the HS9Z-A55 Angle Adjustable (vertical/

horizontal) Actuator

•When the center of the hinged door is used as the reference for the inter-

lock switch contact surface: 50mm

•When the center of the hinged door is used as the reference for the actua-

tor mounting surface: 70mm

•The HS9Z-A55 angle adjustable actuator is made of glass-reinforced PA66

(66 nylon) and the angle adjustment screw is stainless steel. When using

the screw locking agent, make sure that it is compatible with the base

material.

When the center of the hinged door is used as the reference for the interlock

switch contact surface:

50mm

(36.2)

(38)

Vertical Swing

50mm

(36.2)

Horizontal Swing

Door

Hinge

Door

Hinge

Interlock

Switch

Mountin

Hole

Minimum

Radius

Minimum Radius

When the center of the hinged door is used as the reference for the actuator

mounting surface:

70mm

(55.5)

(58)

Vertical SwingHorizontal Swing

Door Hinge

Interlock

Switch

Mounting

Hole

Minimum Radius

When using the HS9Z-A53 Angle Adjustable (vertical) Actuator

•When the center of the hinged door is used as the reference for the inter-

lock switch contact surface: 50mm

•When the center of the hinged door is used as the reference for the actua-

tor mounting surface: 80mm

•Angle adjustment screw recommended tightening torque: 0.8N·m.

50mm

(36.2)

(38)

80mm

(56.5)

(68)

Door

Hinge

Door

Hinge

Interlock

Switch

Mountin

Hole

Interlock

Switch

Mounting

Hole

Minimum Radius