Datasheet

Download catalogs and CAD from http://asia.idec.com/downloads
Benelux B: ([phone] - [e-mail]
NL: (+31) (70) 799 91 51 - [e-mail]
France ([phone] - [e-mail]
Germany Munich: ([phone] - [e-mail]
Hamburg: ([phone] - [e-mail]
Italy ([phone] - [e-mail]
Sweden ([phone] - [e-mail]
United Kingdom ([phone] - [e-mail]
B-396
APEM
Switches &
Pilot Lights
Control Boxes
Emergency
Stop Switches
Enabling
Switches
Safety Products
Explosion Proof
Terminal Blocks
Relays & Sockets
Circuit
Protectors
Power Supplies
LED Illumination
Controllers
Operator
Interfaces
Sensors
AUTO-ID
Switches & Pilot Lights
Flush Silhouette
ø16
ø22
ø30
Miniature
Pilot Lights
HW1Z
AP22
A Series
LD6A
ø12 A2 / ø10 A1 / ø8 A8 Series Miniature Pilot Lights
HW1Z
AP22
A Series
LD6A
Download catalogs and CAD from http://asia.idec.com/downloads
www.apem-idec.eu
Marking
For A series illuminated pushbuttons, legends and symbols can be
engraved on the built-in marking plates, or printed film can be inserted
under the lens.
Marking Plate & Engraving Area
A2 Series
Lens Round Square Rectangular
Built-in Marking Plate
ø9
9
Size: ø10
0.8
Engraving
Area
0.8
Engraving
Area
8
Size: 10
12
Size: 14 x 10
8
0.8
Engraving
Area
• Engraving must be made on the engraving area less than 0.5mm deep.
• The marking plate is made of white acrylic resin.
A1 Series
Lens Round Square Rectangular
Built-in Marking Plate
ø7.5
7.5
Size: ø8.5
0.8
Engraving
Area
0.8
Engraving
Area
7.5
Size: 8.5
11.5
Size: 12.5 x 8.5
7.50.8
Engraving
Area
• Engraving must be made on the engraving area less than 0.5mm deep.
• The marking plate is made of white acrylic resin.
A8 Series
Lens Round Square Rectangular
Built-in Marking Plate
ø5
5
Size: ø6.1
0.8
Engraving
Area
0.8
Engraving
Area
5
Size: 6.1
8
Size: 9.1 x 6.1
50.8
Engraving
Area
• Engraving must be made on the engraving area less than 0.5mm deep.
• The marking plate is made of white acrylic resin.
Other Notes
Close Proximity Mounting
When mounting pilot lights or illuminated pushbuttons collectively or
lighting them continuously, heat may cause the ambient temperature to
rise above the rated operating temperature. When the mounting panel
is not made of metal or when the units are mounted in an enclosed
panel, provide for ventilation or lower the operating voltage.
Replacement of Buttons (Illuminated/Non-illuminated)
Do not replace buttons of maintained action units while the button is
in the locked position. Replacing the button in the locked position may
damage the internal mechanism. Be sure to release the button before
replacing.
Operating and Storage Environment
1. Make sure that the operating/storage temperature and humidity are
within the ratings.
2. Do not use enclosed type units in an environment subject to oil,
water or dust accumulation.
Microswitch Contacts
Do not connect NO and NC contacts of the microswitch to different
voltages or different power sources to prevent a dead short-circuit.
IP65 Units (A2 series only)
IP65 units are evaluated by conventional cutting and cooling oils, and
can not be used with some special oils. Contact IDEC for resistance
against special oils.
Operating Instructions