Datasheet

Download catalogs and CAD from http://asia.idec.com/downloads
B-140
APEM
Switches &
Pilot Lights
Control Boxes
Emergency
Stop Switches
Enabling
Switches
Safety Products
Explosion Proof
Terminal Blocks
Relays & Sockets
Circuit
Protectors
Power Supplies
LED Illumination
Controllers
Operator
Interfaces
Sensors
AUTO-ID
Switches & Pilot Lights
Flush Silhouette
ø16
ø22
ø30
Miniature
Pilot Lights
CW
LW-F
LB
LBW
UP
Flush Bezel
Flush Bezel (Accessories) LB/A6 Series
www.apem-idec.eu
• Turn off the power to the control units before installation, removal,
wiring, maintenance, and inspection. Failure to turn power off may
cause electrical shocks or re hazard.
• To avoid burning your hand, use the lamp holder tool when replacing
lamps.
• For wiring, use wires of a proper size to meet voltage and current
requirements and solder correctly. Improper solder ing may cause
overheating and re hazard. Also, when using tab terminals, use
appropriate quick connect recep tacles.
Panel Mounting of Flush Bezels
1. Remove the locking ring and anti-rotation ring from the operator.
2. Attach the flush bezel to the opera tor. Then insert the assembly into
the panel. Attach the mounting bracket and tighten the locking ring.
(Do not use the anti-rotation ring supplied with the operator.)
For round flush bezels, place the projection on the bezel to the
groove on the TOP side of the operator and mount onto the panel.
Remove
LB/A6 series
Flush bezel / Flush bezel with switchguard
Do not use the anti-rotation
ring supplied with the operator
Locking ring
Mounting panel
Mounting bracket
• Notes on Panel Mounting
Use a locking ring wrench (MT-001) to mount the operator onto the
panel.
Recommended tightening torque is as below:
LB series: 0.5 to 0.7 N·m
A6 series: 0.88 N·m.
Do not use pliers. Excessive tightening will damage the locking ring.
Flush Bezel with Switchguards
Do not apply load on the guard in the direction other than the opening/
closing the guard. Otherwise the hinge part will be damaged.
Installing the Dust Cover
Attach the dust cover and the flush bezel to the LB/A6 series operator.
Then insert the assembly into the panel. Attach the mounting
bracket and tighten the lock ing ring. Tighten the locking ring to the
recommended tightening torque (LB series: 0.5 to 0.7 N·m, A6 series:
0.88N·m). (Do not use the anti-rotation ring supplied with the operator.)
Flush bezel for dustcover
Dust cover for ush silhouette switches
Do not use the anti-rotation
ring supplied with the operator
LB/A6 series
Remove
Mounting bracket
Mounting panel
Locking ring
• Precautions for Installing the Dust Cover
Install the dust cover to wrap around the entire periphery of the flush
bezel. Make sure that the projection on the dust cover is placed into the
groove on the back of the bezel. If the projec tion is not placed correctly,
normal waterproof/dustproof characteristics will not apply.
Good example
Bad example
Dust cover installed
Projection
Attach
Groove
Replacing the Lens
Remove the lens assembly (lens, marking plate, and lens holder) from
the operator by holding the lens removal tool (MT-101) and pull out.
Safety Precautions
Instructions
Benelux B: ([phone] - [e-mail]
NL: (+31) (70) 799 91 51 - [e-mail]
France ([phone] - [e-mail]
Germany Munich: ([phone] - [e-mail]
Hamburg: ([phone] - [e-mail]
Italy ([phone] - [e-mail]
Sweden ([phone] - [e-mail]
United Kingdom ([phone] - [e-mail]
• For other instructions, refer to A6 series pages.