#61-480 480 Platinum Pro Series Commercial Contractor Grade Multimeter Symbols in this Manual This symbol indicates where cautionary or other information is found in the manual. Fuse Battery Refer to Figure 1 and to the following numbered steps to familiarize yourself with the meter’s front panel controls and connectors.
1. Digital Display - The digital display has 3400 counts LCD readout with 70 segments analog bar graph, auto polarity, decimal point, “ “ AC, DC RANGE, HOLD APO and unit annunciators. 2. Rotary Switch - Select the Function and Range desired. 3. COM Input Terminal - Ground input connector. 4. VΩHz Input Terminal - Positive input connector for Volts, Ohms and Frequency. 5. mA Input Terminal - Positive input connector for Amp measurements (up to 340mA). 6.
Overload Protection Function VAC & VDC AAC & ADC AC Volt Circuit Connection: Overload Protection 1000V 1A/500V 10A/500V 600VAC/600VDC 600VAC/600VDC 600VAC/600VDC Ohms (Ω) Diode Continuity APO RPM Hz Unit of Measure Multipliers For your reference, the following symbols are often used to make measurement easier: Symbol Verbal Multiplier M mega x 1,000,000 k kilo x 1,000 m milli ÷ 1,000 µ micro ÷ 1,000,000 Auto Power Off (APO) The APO sign on the LCD panel indicates the meter is working in the Auto Power
DC Volts AC Current Circuit Connection: Circuit Connection: APO RPM APO RPM Hz Range 300mV 3V 30V 300V 750V Resolution 100µV 1mV 10mV 100mV 1V Hz Max Display Accuracy 300.0 ±(0.25% +1)* 3.000 30.00 300.0 750 Input Impedance: 10MΩ (over 1000MΩ in 300 mV range) ±(0.4% reading +1 digit) in 3V range To Measure DC Voltage: 1. Plug the black test lead into the COM port and the red test lead into the VΩHz port. 2. Set the rotary switch to the V position. 3.
Frequency/RPM DC Current Circuit Connection: Circuit Connection: APO RPM APO RPM Hz Hz Range Resolution 30mA 300mA 10A 10µA 0.1mA 10mA Max Display 30.00 300.0 10.00 Accuracy ±(1.5% +2) ±(1.5% +2) ±(2.0% +2) Voltage Burden 200Vmax 2Vmax 2V max Overload Protection: 1A (500V) fast blow fuse for mA input 10A (500V) fast blow fuse for A input To Measure DC Current: 1. Plug the black test lead into the COM port and the red test lead into the mA or A port. 2.
Resistance (Ohms) Circuit Connection: APO RPM Hz Range 300Ω 3kΩ 30kΩ 300kΩ 3MΩ 30MΩ Resolution 0.1Ω 1Ω 10Ω 100Ω 1kΩ 10kΩ MaxDisplay 300.0 3.000 30.00 300.0 3.000 30.00 Accuracy ±(1.0% +4) ±(0.7% +3) Range Guide for Ohms (Ω): 300 = Meter indicates actual resistance 3k = Multiply meter display reading by 1,000 to acquire actual resistance. 30k = Multiply meter display reading by 1,000 to acquire actual resistance. 300k = Multiply meter display reading by 1,000 to acquire actual resistance.
Resistor Color Code Table 1st Color Digit Black 0 Brown 1 Red 2 Orange 3 Yellow 4 Green 5 Blue 6 Violet 7 Gray 8 White 9 Gold Silver No Color 2nd Tolerance Digit Multiplier (Percentage) 0 1 1 10 2 100 3 1,000 4 10,000 5 100,000 6 1,000,000 7 10,000,000 8 100,000,000 9 1,000,000,000 +/- 5% +/- 10% +/- 20% Diode Testing Circuit Connection: APO RPM Hz Function Resolution Accuracy Max.Test Max.Open Current Circuit Voltage 1mV +(1.5% +5)* 1.5mA 3V * For 0.4V to 0.8V.
Accessories Continuity Check Circuit Connection: APO RPM APO RPM Hz Hz To Verify Continuity: A continuity test ensures that all circuit connections are intact. 1. Plug the black test lead into the COM port and the red test lead into the VΩHz port. 2. Set the rotary switch to the Ω position. 3. Press the blue button until is shown in the display. 4. Connect the test leads to the circuit to be measured. The buzzer will sound if the resistance of the circuit measured is lower than 30Ω.
General Specifications LCD Display: 3400 count maximum reading Bar Graph Display: 70 segment analog bar graph Polarity Indication: Automatic, negative indicated, positive implied Overrange Indication: “OL” or “-OL” Low Battery Indication: “ ” when the battery voltage drops below operating voltage Size (WxHxD): 88mm x 180mm x 33.5mm (without holster) 94mm x 188mm x 40mm (with holster) Sampling: 2 times/sec LCD Display, 12 times/sec bar graph Auto Power Off: Approx. 10 min.
Lifetime Limited Warranty This meter is warranted to the original purchaser against defects in material or workmanship for the lifetime of the meter. During this warranty period, IDEAL INDUSTRIES, INC. will, at its option, replace or repair the defective unit, subject to verification of the defect or malfunction. This warranty does not apply to defects resulting from abuse, neglect, accident, unauthorized repair, alteration, or unreasonable use of the instrument.
