Installation Guide

1. Frequent maintenance is important to keep the tool in good work-
ing condition.
2. To ensure smooth operation and prevent rust, store the tool in a
cool, dry area.
3. Ensure that blades are clean and sharp for optimal performance.
4. Inspect blades for damage or burrs. If burrs exist, they can be
removed with a flat grinding stone or file on the back sides of the
blades.
5. Keep handle and torque arm dry, clean and free from oil or grease.
These can be cleaned with a soft cloth using mild soap and water.
Do not submerge gear box in water. Wipe unit completely dry after
cleaning.
6. Occasionally oil blades with a light cutting oil.
7. If the tool is maintained regularly, it should provide you with
trouble-free service.
8. The large shoulder screw used to attach the blades together may
loosen during use, especially when making many cuts on larger
cable sizes (750 MCM), or when blades become dull. Tighten
shoulder screw, then loosen
1
⁄4 turn to adjust. If this screw loosens
too frequently, or if blades smash cable instead of cutting, replace
blade assembly as shown on page 3.
9. A generic shear pin locks the output gear to the output shaft. If
too much torque is placed on the pin and it is damaged, it can
be replaced with a standard
1
⁄8 square key, available at your local
hardware store.
Gearbox is lubricated and sealed for the life of the tool. Do not
open the gearbox for any reason; opening will void all warranties.
Maintenance and Inspection
Innovation by IDEAL,
the Brand Electricians Trust
10/13
Printed in U.S.A.
ND-5095
©2013 IDEAL INDUSTRIES, INC.
IDEAL INDUSTRIES, INC.
Becker Place, Sycamore, IL 60178, USA / 815-895-5181 • 800-435-0705 in USA
International offices:
Australia • Brazil • Canada • China • Germany • Mexico • UK
For complete sales office contact information, visit us at:
www.idealindustries.com
Use and Care Manual
Use and Care Manual
1. Do not drop or abuse the unit.
2. Do not disassemble, repair or modify the assembly, except to
replace parts as shown on page 3.
3. Do not expose the unit to water or solvents.
4. Do not cut cables larger than those listed in the specifications.
5. Set drill to 1500 RPM for best performance. Cutting large cable
at high RPM will damage gears!
6. Do not use tool in the rain to prevent blade wear and malfunction.
7. Store cutter in case provided, in a dry, secure area.
8. We strongly recommend using a reversible drill to enable backing
out of a cut when necessary.
Specifications
Cable Cutter Assembly:
35-078
Drill Specifications:
Any drill 12V or larger that accepts
3
⁄89 drive shaft
Cutting Capacity: 750 MCM Hard Drawn Copper and
up to 29 O.D. Aluminium
RPM Specifications:
Low Speed RPM Setting
WARNINGS
1. Do not overreach. Keep proper footing and balance at all times.
2. Keep out of reach of children.
3. Always wear safety glasses when using this tool.
Do not cut steel, ACSR or any other
materials containing steel or damage
to blades will result.
#35-078
Accepts almost any
cordless or corded drill
Adjustable torque arm
holds drill in place
Ergonomically designed, textured
Santoprene
®
non-slip grip
Handle folds for
easy storage
Contour blade
design minimizes
cable distortion
Replaceable hardened steel
blades ensure consistent cuts
and long-term durability
Rugged metal housing
Durable gears
4. Do not use on live circuits. Always disconnect power
before using this tool.
5. Keep hands away from blades while operating unit.
6. Never operate tool without torque arm installed.
7. Blade is sharp; contact with blade can result in serious
personal injury.
8. Disconnect drill from power source before servicing. Always
remove drill from unit before attempting to change blades.
Failure to heed all warnings and precautions outlined
in this manual may lead to serious personal injury.