Instructions / Assembly

ManualsBrandsIDEAL Security ManualsTools & HardwareDeluxe Storm and Screen Door Lever Handle and Keyed Deadlock in Antique Brass

Table Of Contents

5/16"

6 PLCS

1 3/4" 1 3/4"

5 1/8"

1 5/32"

13/32"

2 1/2"

1 5/32"

15/16"

1/16"

8 PLCS

HK01-I Template and installation instructions

Warning: Verify door profile prior to installation

You will require a profile wide enough for proper installation.

With the door closed, the minimum inside door profile width is 1-7/8” from the edge of the door frame (glass side) to

the edge of the door jamb or metal door frame (z-bar), which ever is narrower.

The minimum outside door profile width is 2” from the edge of the door frame (glass side) to

the edge of the door jamb or metal door frame Z-bar), which ever is narrower.

Drilling template prerequisite: Determine if your storm door is right or left handed

From outside of the door, looking in, if the hinges are on your left, your door is left handed. Your door will open to the left side.

If the hinges are on your right, your door is right handed. Your door will open to the right side.

Ensure that the inside latch paddle does not interfere with the prime door lock.

cutting linecutting line

RFQHKE

PAGE 1 OF 4

Summary of content (5 pages)

PAGE 1
HK01-I Template and installation instructions RFQHKE Warning: Verify door profile prior to installation You will require a profile wide enough for proper installation. With the door closed, the minimum inside door profile width is 1-7/8” from the edge of the door frame (glass side) to the edge of the door jamb or metal door frame (z-bar), which ever is narrower.
PAGE 2
Template Placement and Drilling Instructions JAMB 1. Fold the template on the dotted line to 90 according to the handedness (left or right). DOOR 2. With the door in closed position, place folded template on the inside of the door so that the SIDE A is against the jamb or metal z-bar, which ever projects out furthest; and SIDE B is on the inside surface of the door. 3. Use a center punch to mark the position of 6 holes on the inside surface of the door on SIDE B.
PAGE 3
SPINDLES AND SCREWS SELECTION HANDLE SPINDLE SELECTION DOOR THICKNESS LATCH SCREW SELECTION DOOR THICKNESS ALIGN CAP OF SPINDLE HERE 1" 1"~1 1/4" 1 1/4" 1 1/2" 1 3/4" 1 1/2" 2" 1 3/4" 2 1/8" 2" 1. Print out this sheet using 1:1 scale. 2. Over lay screws on top of the image. 3. Select the screws that matche your door thickness. 2 1/8" The latch screws have now been selected and are ready for installation. ALIGN CAP OF SPINDLE HERE 1. Print out this sheet using 1:1 scale. 2.
PAGE 4
Handle & Latch Installation 1. Rotate the outside handle to the left or right according to your door handedness. 2. Insert the pre-selected handle spindle (see page 3) into the center hole of the outside handle from the back side of the handle housing; ensure the spindle is fully sitted into the hole. The spindle locks the handle in place. 3. Place the outside handle assembly on the door.
PAGE 5
1.312 in 33.3 mm 1.641 in 41 mm 1.142 in 29 mm 1.750 in 44.5 mm 1.250 in 31.8 mm 2.725 in 69.2 mm 2.760 in 70 mm 1.750 in 44.5 mm .877 in 22.3 mm 2.500 in 63.5 mm 4.455 in 113 mm 3.878 in 98.5 mm 1.138 in 29 mm 1.655 in 42 mm 2.125 in 54 mm 1.926 in 49 mm .500 in 12.7 mm HK01-I DIMENSIONS .359 in 9.