Instructions / Assembly

ManualsBrandsIDEAL Security ManualsDoor Accessories15 in. to 26 in. White Adjustable Window Security Bar with Child-Proof Lock for Ventilation

PROFILE AND FRAME TYPES

There are many different types of window proﬁles and frames

Some of the most common types are illustrated below:

INSTALLATION

General installation steps

1 Determine where on the window you want to install the bar. Make sure it is

clear of interference and will have enough space to be removed from the

saddles.

2 Place one of the saddle brackets against the window frame at the desired

location. Mark the 3 hole locations.

3 Install the saddle bracket (and optional anti-lift lock) following the

instructions below for using double sided tape or screws.

4 Place the ﬁxed end of the bar in the installed saddle, hold the bar in a level

position (either ﬂat horizontally or straight down vertically), and extend the

sliding end and mark the location on the opposite window proﬁle

5 Install the second bracket (and optional anti-lift lock) following the

instructions below for using double sided tape or screws.

ANTI-LIFT LOCK

SADDLE BRACKET

FIXED END OF BAR

SLIDING END OF BAR

SLIDING WINDOW SECURITY BAR

External pane

External

pane

Window Frame

Window Profile

Internal pane

Internal

pane

BEFORE INSTALLING Know Your Window

With the window closed

measure “A” from the

inside of the window

frame to the inside of the

window profile.

COMPATIBILITY / REQUIREMENTS

• If installing with the saddle brackets, you will need at least 1” of clear

surface space on both the window frame and window proﬁle.

• See the chart above to determine if your window frame and proﬁle will

support the saddle brackets with screws and/or tape.

• When determining the installation location on the window, ensure it will

not interfere with any existing window hardware such as sash locks or

window release buttons. Ensure you will have enough room to easily

remove the bar for emergency exit.

NOTE:

Will only be effective on windows with a locking or fixed exterior pane.

Min A Max A Window / Door Model Number

10.6” 16.625” Small windows SK112

15.7” 26.75” Medium windows & narrow doors SK111

25.75” 47.5” Standard sliding patio doors SK110

FLAT PROFILE:

CENTER GROOVED: ALL GROOVED:

SIDE GROOVED:

.956”

24.28mm

.723”

18.36mm

.512”

13mm

1.425”

36.20mm

.471”

11.96mm

CHOOSE THE RIGHT MODEL

SADDLE BRACKET

The anti-lift lock is required at the the top

bracket to prevent the bar from falling down.

The bar must always be inserted with the

narrower inner section facing up. Otherwise

the release button will self-release due to

gravity. There is an arrow on the release

button indicating the installation direction.

1”

MIN.

NOTE:

If installing in a vertical slider (single hung) window.

SLIDING END OF BAR

KEEP BAR LEVEL

MARK LOCATION

1”

MIN.

3/4”

1”

MIN.

1”

MIN.

1”

MIN.

1”

MIN.

3/4”

MOUNT WITH:

✔ Screws

✔ Tape

Requires 1” minimum

width.

MOUNT WITH:

✘ Screws

✔ Tape

3/4” Minimum ﬂat

surface area for tape.

MOUNT WITH:

✘ Screws

✔ Tape

3/4” Minimum ﬂat

surface area for tape.

The saddle bracket

cannot be used

Lay the security bar

directly in the track

of a horizontal

window if the track

is at least 1” wide.

Summary of content (2 pages)

PAGE 1
SLIDING WINDOW SECURITY BAR BEFORE INSTALLING Know Your Window PROFILE AND FRAME TYPES INSTALLATION There are many different types of window profiles and frames General installation steps Some of the most common types are illustrated below: 1 Determine where on the window you want to install the bar. Make sure it is clear of interference and will have enough space to be removed from the saddles. SIDE GROOVED: FLAT PROFILE: 1” MIN. 1” MIN.
PAGE 2
OPERATION Installation with double sided tape 1 If using the optional anti-lift lock, first use the included double sided tape to attach the anti-lift lock to the window frame or profile. DOUBLE YOUR WARRANTY idealinc.com/register The SK111 and SK112 Window Security Bars extend and retract easily, allowing you to keep your window locked in any position. 2 Now tape the bracket either to the anti-lift lock, or directly to the window frame or profile. Repeat for the second bracket.