Installation Instructions

P03-R01-0704
9
Track Bracket
(Longer)
Track Bracket
(Shorter)
#2 Hinge
#3 Hinge
#4 Hinge
(5 Section
Doors Only)
Top Bracket
3/8"-18 x 3/4"
Lg. Carriage Bolt
Bottom Bracket
(1) LH + (1) RH
Flag
Bracket
(1) LH +
(1) RH
Cable Assembly
Vertical
Track
Curved
Horizontal Track
3/8" Washer
Horizontal Angle
Struts*
1/4" x 3/4"
Hex Head
Self-Tapping
Screw
#14 x 5/8"
Hex Head
Sheet Metal
Screw
1/4" Flange Nut
3/8" Hex Nut
Lift Handle
Inside
Step Plate
1/4" x 5/8"
Track Bolt
5/16" x 1-5/8"
Lag Bolt
#1 Hinge
Rollers
Description
Description:Qty. Qty.
Door Size:Door Size:
Single Car Doors
8' - 9'W x 6'6'' - 7'0''H
Double Car Doors
16'W x 6'6" - 7'0''H
4 Section Doors
5 Section Doors
Pull Rope
Single Car Doors
8' - 9'W x 6'6'' - 7'0''H
Double Car Doors
16'W x 6'6" - 7'0''H
Single Car Doors
8' - 9'W x 6'6'' - 7'0''H
Double Car Doors
16'W x 6'6" - 7'0''H
5 Section Doors
4 Section Doors
Single Car Doors
8' - 9'W x 6'6'' - 7'0''H
Double Car Doors
16'W x 6'6" - 7'0''H
Single Car Doors
8' - 9'W x 6'6'' - 7'0''H
Double Car Doors
16'W x 6'6" - 7'0"H
All Doors
All Doors
All Doors
Keyed Lock Kit (If included,
parts are detailed in Lock
instructions)
All Doors
All Doors Will Receive (2) Of These Items:
(While not representative of any one model, the quantities below can be used as a guide. In some
instances, extra screws/bolts are provided in the event of strip out or loss of parts.)
*More struts may be required in high windload areas.
Single Car Doors
8' - 9'W x 6'6'' - 7'0''H
Double Car Doors
16'W x 6'6" - 7'0''H
10
12
5
11
1 or 2
16
22
10
12
1 or 2 0 or 1
16
22
0
10
56
90
0
1
1
Hardware Components
NOTE: All doors will receive (1) spring kit and (1) or more springs. Separate spring installation supplemental
instructions should be included with door hardware. This supplement contains a list of all spring related hardware
along with instructions on proper spring installation.
P03-R01-0704
STEP 9 - Installing Door Sections
Step 9-1: Place the section in the opening so that it is against
the stop molding and centered from side to side. Place a level
on the section and use a piece of wood under one end or the
other (if necessary) to make the section level. (FIG. 9-A)
Step 9-2: Remove the level and drive a 3” nail in the jambs at
each end and bend it over the edge of the section to hold the
section in place. (FIG. 9-B)
NOTE: These nails are all that will hold the stacked door
section in place until the tracks are secured to the back jambs.
Be sure the nails hold the sections  rmly in position.
Step 9-3: With the Table 9-A below, determine the order in
which you will attach the remaining sections.
NOTE: If a lock assembly was ordered with the door, the holes
for the lock may be predrilled. (Lock templates are included in
the lock instructions for doors without predrilled holes.)
* Section with general safety label.
Step 9-4: Place the next section face down on the saw horses.
If your door is predrilled for a lock, this section will be the one
with holes in the center of the panel face. Identify the bottom
edge as shown in the illustration. (FIG. 9-C)
Attach a number 2 hinge to each end at the top edge using
#14 x 5/8" sheet metal screws. Remember that the number
is stamped on the side of the hinge that is to be attached to
the section. Attach a number 1 hinge to at each center stile
location along the top edge of the section.
Step 9-5: Keyed Lock Installation. If you wish to install a
keyed lock, begin the lock installation now according to the
supplemental instructions included with the lock hardware. If
your door did not come with a keyed lock, install lift handle as
shown on previous page.
1st 2nd
Door (Bottom) (Lock) 3rd 4th 5th
Height Section Section Section* Section Section
6'0" 18" 18" 18" 18" -
6'3" 18" 18" 18" 21" -
6'6" 21" 18" 18" 21" -
6'9" 21" 21" 18" 21" -
7'0" 21" 21" 21" 21" -
7'6" 18" 18" 18" 18" 18"
7'9" 18" 18" 18" 18" 21"
8'0" 21" 18" 18" 18" 21"
FIG. 9-A
Stop Molding
12
Table 9-A - Section Order for Various Door Heights
FIG. 9-B
FIG. 9-C
33
Center Stile
#1 Hinge
#2 Hinge
Bottom
Edge
End
Stile