SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE 2011-2013 Ford Edge with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Edge with MyFord touch with Sony amp 2011-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Edge with MyFord touch with Sony amp 2011-2013 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the two (2) trim panels at the left and right of the OEM radio. (Fig. 1.1) 2. Remove four (4) screw holding the shifter trim panel. Unclip and remove the shifter trim panel. (Fig. 1.2) 3. Remove six (6) 7mm screws holding the radio and climate control panel. (Fig. 1.3) 4. Use a panel removal tool to unclip and release the radio and climate panel from the dash. (Fig. 1.3) Fig. 1.1 Fig. 1.
Ford Edge with MyFord touch with Sony amp 2011-2013 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Edge with MyFord touch with Sony amp 2011-2013 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford Edge with MyFord touch with Sony amp 2011-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Edge with MyFord touch with Sony amp 2011-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
LIMITED 1-YEAR WARRANTY GARANTiA LIMITADA POR 1ANO Automotive Data Solutions Inc. I ..ADS .. I warrants to the original purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances, for the period of one 111 year as of the original date of purchase. Automotive Data Solutions Inc. I..ADS ..
WEB-PROGRAMMING STEPS ETAPES DE PROGRAMMATION WEB Ii\ THIS PRODUCT REQUIRES THE INSTALLATION OF ~ AMAESTRO RR (ADS·MRR] MODULE SOLD SEPARATELY Ii\ CE PRODUIT NECESSITE L'INSTALL~TION,D'UN MODULE ~ MAESTRO RR [ADS·MRR] VENDU SEPAREMENT Ii\ ESTE PRODUCTO REOUIERE LA INSTALACION DEL MODULO ~ MAESTRO RR (ADS-MRR) VENDIDO POR SEPARADO G) INSTALL THE WEBLINK PLUGIN (FOR PC ONLY) G) G) 0 REGISTER AWEB LINK ACCOUNT Go to idatalinkmaestro.com/plugin and follow the installation steps.
INSTALL GUIDE 2014-2019 Ford Edge with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Edge with MyFord touch with Sony amp 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Edge with MyFord touch with Sony amp 2014-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: Requires shallow mount radio. Requires trimming in the dash. 1. Unclip and remove the two (2) trim panels at the left and right of the center console. (Fig. 1.1) 2. Unclip and remove the center console trim panel (around the shifter). Unplug the connectors. (Fig. 1.2) 3. Remove four (4) 5.5mm screws holding storage compartment in front of the center console. Remove and unplug it. (Fig. 1.3) Fig. 1.1 Fig.
Ford Edge with MyFord touch with Sony amp 2014-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Edge with MyFord touch with Sony amp 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford Edge with MyFord touch with Sony amp 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Edge with MyFord touch with Sony amp 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2011-2013 Ford Edge with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Edge with MyFord touch without amp 2011-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Edge with MyFord touch without amp 2011-2013 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the two (2) trim panels at the left and right of the OEM radio. (Fig. 1.1) 2. Remove four (4) screw holding the shifter trim panel. Unclip and remove the shifter trim panel. (Fig. 1.2) 3. Remove six (6) 7mm screws holding the radio and climate control panel. (Fig. 1.3) 4. Use a panel removal tool to unclip and release the radio and climate panel from the dash. (Fig. 1.3) Fig. 1.1 Fig. 1.
Ford Edge with MyFord touch without amp 2011-2013 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Edge with MyFord touch without amp 2011-2013 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Edge with MyFord touch without amp 2011-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Edge with MyFord touch without amp 2011-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2014-2019 Ford Edge with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Edge with MyFord touch without amp 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Edge with MyFord touch without amp 2014-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: Requires shallow mount radio. Requires trimming in the dash. 1. Unclip and remove the two (2) trim panels at the left and right of the center console. (Fig. 1.1) 2. Unclip and remove the center console trim panel (around the shifter). Unplug the connectors. (Fig. 1.2) 3. Remove four (4) 5.5mm screws holding storage compartment in front of the center console. Remove and unplug it. (Fig. 1.3) Fig. 1.1 Fig. 1.
Ford Edge with MyFord touch without amp 2014-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Edge with MyFord touch without amp 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Edge with MyFord touch without amp 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Edge with MyFord touch without amp 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2016 Ford Escape with MyFord touch with Sony amp with parking assist RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Escape with MyFord touch with Sony amp with parking assist 2013-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Escape with MyFord touch with Sony amp with parking assist 2013-2016 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: If you are installing a standard sized double din radio, trimming is required to make the radio fit. 1. Using a plastic pry tool, remove the upper trim by pulling upward. (Fig. 1.1) 2. Remove the two (2) 7mm screws from the radio bezel. (Fig. 1.2) 3. Unclip and remove the radio bezel by prying with a plastic panel too. Unplug the connector from the panel and set it aside. (Fig. 1.
Ford Escape with MyFord touch with Sony amp with parking assist 2013-2016 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Escape with MyFord touch with Sony amp with parking assist 2013-2016 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT CONNECT TO AFTERMARKET RADIO BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford Escape with MyFord touch with Sony amp with parking assist 2013-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle
Ford Escape with MyFord touch with Sony amp with parking assist 2013-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module.
INSTALL GUIDE 2013-2016 Ford Escape with MyFord touch with Sony amp without parking assist RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Escape with MyFord touch with Sony amp without parking assist 2013-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Escape with MyFord touch with Sony amp without parking assist 2013-2016 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: If you are installing a standard sized double din radio, trimming is required to make the radio fit. 1. Using a plastic pry tool, remove the upper trim by pulling upward. (Fig. 1.1) 2. Remove the two (2) 7mm screws from the radio bezel. (Fig. 1.2) 3. Unclip and remove the radio bezel by prying with a plastic panel too. Unplug the connector from the panel and set it aside. (Fig. 1.
Ford Escape with MyFord touch with Sony amp without parking assist 2013-2016 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Escape with MyFord touch with Sony amp without parking assist 2013-2016 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford Escape with MyFord touch with Sony amp without parking assist 2013-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehi
Ford Escape with MyFord touch with Sony amp without parking assist 2013-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module.
INSTALL GUIDE 2013-2019 Ford Escape with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Escape with MyFord touch without amp 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Escape with MyFord touch without amp 2013-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: If you are installing a standard sized double din radio, trimming is required to make the radio fit. 1. Using a plastic pry tool, remove the upper trim by pulling upward. (Fig. 1.1) 2. Remove the two (2) 7mm screws from the radio bezel. (Fig. 1.2) 3. Unclip and remove the radio bezel by prying with a plastic panel too. Unplug the connector from the panel and set it aside. (Fig. 1.3) Fig. 1.1 Fig. 1.
Ford Escape with MyFord touch without amp 2013-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Escape with MyFord touch without amp 2013-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Escape with MyFord touch without amp 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Escape with MyFord touch without amp 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2015-2017 Ford Expedition with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Expedition with MyFord touch with Sony amp 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Expedition with MyFord touch with Sony amp 2015-2017 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: Climate control module needs to be relocated to the bottom where the oem radio body was. 1. Unclip and remove the trim panel at the bottom of the climate control panel. (Fig. 1.1) Remove two (2) 7mm screws behind it. (Fig. 1.2) 2. Unclip and remove the radio and climate control panel, starting from the bottom. Unplug the connectors. (Fig. 1.3) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.
Ford Expedition with MyFord touch with Sony amp 2015-2017 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Expedition with MyFord touch with Sony amp 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 RCA CABLES WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP.
Ford Expedition with MyFord touch with Sony amp 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor)
Ford Expedition with MyFord touch with Sony amp 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2015-2019 Ford Expedition with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Expedition with MyFord touch without amp 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Expedition with MyFord touch without amp 2015-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: Climate control module needs to be relocated to the bottom where the oem radio body was. 1. Unclip and remove the trim panel at the bottom of the climate control panel. (Fig. 1.1) Remove two (2) 7mm screws behind it. (Fig. 1.2) 2. Unclip and remove the radio and climate control panel, starting from the bottom. Unplug the connectors. (Fig. 1.3) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.
Ford Expedition with MyFord touch without amp 2015-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Expedition with MyFord touch without amp 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Expedition with MyFord touch without amp 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (D
Ford Expedition with MyFord touch without amp 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2011-2015 Ford Explorer with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Explorer with MyFord touch with Sony amp 2011-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Explorer with MyFord touch with Sony amp 2011-2015 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: In some cases the heated steering wheel module will need to be relocated. (Fig. 1.6) Requires shallow mount radio. Requires trimming. 1. Unclip and remove the two (2) trim panels at the left and right of the OEM radio. (Fig. 1.1) 2. Remove four (4) 7mm screws holding the radio and climate control panel. (Fig. 1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 3.
Ford Explorer with MyFord touch with Sony amp 2011-2015 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Explorer with MyFord touch with Sony amp 2011-2015 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford Explorer with MyFord touch with Sony amp 2011-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (D
Ford Explorer with MyFord touch with Sony amp 2011-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2016-2017 Ford Explorer with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Explorer with MyFord touch with Sony amp 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Explorer with MyFord touch with Sony amp 2016-2017 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: In some cases the heated steering wheel module will need to be relocated. (Fig. 1.6) Requires shallow mount radio. Requires trimming. 1. Unclip and remove the two (2) trim panels at the left and right of the OEM radio. (Fig. 1.1) 2. Remove four (4) 7mm screws holding the radio and climate control panel. (Fig. 1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 3.
Ford Explorer with MyFord touch with Sony amp 2016-2017 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Explorer with MyFord touch with Sony amp 2016-2017 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford Explorer with MyFord touch with Sony amp 2016-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (D
Ford Explorer with MyFord touch with Sony amp 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2011-2015 Ford Explorer with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Explorer with MyFord touch without amp 2011-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Explorer with MyFord touch without amp 2011-2015 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: In some cases the heated steering wheel module will need to be relocated. (Fig. 1.6) Requires shallow mount radio. Requires trimming. 1. Unclip and remove the two (2) trim panels at the left and right of the OEM radio. (Fig. 1.1) 2. Remove four (4) 7mm screws holding the radio and climate control panel. (Fig. 1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 3.
Ford Explorer with MyFord touch without amp 2011-2015 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Explorer with MyFord touch without amp 2011-2015 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Explorer with MyFord touch without amp 2011-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DAT
Ford Explorer with MyFord touch without amp 2011-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2016-2019 Ford Explorer with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Explorer with MyFord touch without amp 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Explorer with MyFord touch without amp 2016-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: In some cases the heated steering wheel module will need to be relocated. (Fig. 1.6) Requires shallow mount radio. Requires trimming. 1. Unclip and remove the two (2) trim panels at the left and right of the OEM radio. (Fig. 1.1) 2. Remove four (4) 7mm screws holding the radio and climate control panel. (Fig. 1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 3.
Ford Explorer with MyFord touch without amp 2016-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Explorer with MyFord touch without amp 2016-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Explorer with MyFord touch without amp 2016-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DAT
Ford Explorer with MyFord touch without amp 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2016 Ford F Super Duty with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford F Super Duty with MyFord touch with Sony amp 2013-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford F Super Duty with MyFord touch with Sony amp 2013-2016 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: Temperature control module needs to be relocated to where the factory radio body was, metal brace at the top needs to be removed. (Fig. 1.5) Requires shallow mount radio. Requires trimming. 1. Unclip the two (2) panels at the bottom of the factory bezel. (Fig. 1.1) Remove two (2) 7mm screws behind the panels. (Fig. 1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 2.
Ford F Super Duty with MyFord touch with Sony amp 2013-2016 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford F Super Duty with MyFord touch with Sony amp 2013-2016 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford F Super Duty with MyFord touch with Sony amp 2013-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor)
Ford F Super Duty with MyFord touch with Sony amp 2013-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2017-2019 Ford F Super Duty with MyFord touch with Sony or B&O amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford F Super Duty with MyFord touch with Sony or B&O amp 2017-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford F Super Duty with MyFord touch with Sony or B&O amp 2017-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. If the vehicle is equipped with a center channel speaker: Pop the speaker grille up (A), unscrew (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.0) If there is no center channel speaker: lift the rubber mat at the top of the dash (A), then remove (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.1) A B C 2. Remove the (2) 7mm bolts from the top of the radio panel.
Ford F Super Duty with MyFord touch with Sony or B&O amp 2017-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford F Super Duty with MyFord touch with Sony or B&O amp 2017-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford F Super Duty with MyFord touch with Sony or B&O amp 2017-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed
Ford F Super Duty with MyFord touch with Sony or B&O amp 2017-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2016 Ford F Super Duty with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford F Super Duty with MyFord touch without amp 2013-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford F Super Duty with MyFord touch without amp 2013-2016 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: Temperature control module needs to be relocated to where the factory radio body was, metal brace at the top needs to be removed. (Fig. 1.5) Requires shallow mount radio. Requires trimming. 1. Unclip the two (2) panels at the bottom of the factory bezel. (Fig. 1.1) Remove two (2) 7mm screws behind the panels. (Fig. 1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 2.
Ford F Super Duty with MyFord touch without amp 2013-2016 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford F Super Duty with MyFord touch without amp 2013-2016 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford F Super Duty with MyFord touch without amp 2013-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor)
Ford F Super Duty with MyFord touch without amp 2013-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2017-2020 Ford F Super Duty with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford F Super Duty with MyFord touch without amp 2017-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford F Super Duty with MyFord touch without amp 2017-2020 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. If the vehicle is equipped with a center channel speaker: Pop the speaker grille up (A), unscrew (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.0) If there is no center channel speaker: lift the rubber mat at the top of the dash (A), then remove (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.1) A B C 2. Remove the (2) 7mm bolts from the top of the radio panel.
Ford F Super Duty with MyFord touch without amp 2017-2020 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford F Super Duty with MyFord touch without amp 2017-2020 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford F Super Duty with MyFord touch without amp 2017-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor)
Ford F Super Duty with MyFord touch without amp 2017-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2021 Ford F Super Duty with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit FO3 adapter OPTIONAL ACCESSORIES E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford F Super Duty with MyFord touch without amp 2021 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford F Super Duty with MyFord touch without amp 2021 INSTALLATION INSTRUCTIONS BEFORE INSTALLING • FO3 adapter is required to complete this install. A B DASH DISASSEMBLY 1. If the vehicle is equipped with a center channel speaker: Pop the speaker grille up (A), unscrew (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.0) If there is no center channel speaker: lift the rubber mat at the top of the dash (A), then remove (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.1) C Fig. 1.
Ford F Super Duty with MyFord touch without amp 2021 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford F Super Duty with MyFord touch without amp 2021 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford F Super Duty with MyFord touch without amp 2021 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA
Ford F Super Duty with MyFord touch without amp 2021 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2014 Ford F-150 with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford F-150 with MyFord touch with Sony amp 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford F-150 with MyFord touch with Sony amp 2013-2014 INSTALLATION INSTRUCTIONS VEHICLE DASH DISASSEMBLY NOTE: Top bracket needs to be bent up or removed, rear radio hanger bracket needs to be cut off or bent back. 1. On passenger side of the vehicle, open the glove box and push the side tabs toward each other to release glove box. Extract (3) 8mm bolts to release the airbag. (1.1) (1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 Fig. 1.7 Fig. 1.8 2.
Ford F-150 with MyFord touch with Sony amp 2013-2014 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford F-150 with MyFord touch with Sony amp 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford F-150 with MyFord touch with Sony amp 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA
Ford F-150 with MyFord touch with Sony amp 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2015-2017 Ford F-150 with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford F-150 with MyFord touch with Sony amp 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford F-150 with MyFord touch with Sony amp 2015-2017 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. If the vehicle is equipped with a center channel speaker: Pop the speaker grille up (A), unscrew (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.0) If there is no center channel speaker: lift the rubber mat at the top of the dash (A), then remove (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.1) A B C 2. Remove the (2) 7mm bolts from the top of the radio panel.
Ford F-150 with MyFord touch with Sony amp 2015-2017 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford F-150 with MyFord touch with Sony amp 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) BLUE - POWER ANTENNA ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Ford F-150 with MyFord touch with Sony amp 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA
Ford F-150 with MyFord touch with Sony amp 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2014 Ford F-150 with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford F-150 with MyFord touch without amp 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford F-150 with MyFord touch without amp 2013-2014 INSTALLATION INSTRUCTIONS VEHICLE DASH DISASSEMBLY NOTE: Top bracket needs to be bent up or removed, rear radio hanger bracket needs to be cut off or bent back. 1. On passenger side of the vehicle, open the glove box and push the side tabs toward each other to release glove box. Extract (3) 8mm bolts to release the airbag. (1.1) (1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 Fig. 1.7 Fig. 1.8 2.
Ford F-150 with MyFord touch without amp 2013-2014 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford F-150 with MyFord touch without amp 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford F-150 with MyFord touch without amp 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford F-150 with MyFord touch without amp 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2015-2020 Ford F-150 with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford F-150 with MyFord touch without amp 2015-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford F-150 with MyFord touch without amp 2015-2020 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. If the vehicle is equipped with a center channel speaker: Pop the speaker grille up (A), unscrew (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.0) If there is no center channel speaker: lift the rubber mat at the top of the dash (A), then remove (2) 7mm bolts from the tray (B), and remove it (C). (Fig. 1.1) A B C 2. Remove the (2) 7mm bolts from the top of the radio panel.
Ford F-150 with MyFord touch without amp 2015-2020 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford F-150 with MyFord touch without amp 2015-2020 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford F-150 with MyFord touch without amp 2015-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford F-150 with MyFord touch without amp 2015-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2019 Ford Flex with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Flex with MyFord touch with Sony amp 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Flex with MyFord touch with Sony amp 2013-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the shifter bezel (Fig. 1.1) 2. Unclip and remove the trim above the radio and glove box. (Fig. 1.2) Remove two (2) 7mm screws behind the trim. (Fig. 1.3) 3. Remove the panels on each side of the center console, exposing (1) 7mm screw on each side. Remove the two (2) screws. (Fig. 1.4) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 Fig. 1.7 Fig. 1.8 4.
Ford Flex with MyFord touch with Sony amp 2013-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Flex with MyFord touch with Sony amp 2013-2019 WIRING DIAGRAM STEP 4 STEP 1 RCA CABLES WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP.
Ford Flex with MyFord touch with Sony amp 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Flex with MyFord touch with Sony amp 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2019 Ford Flex with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Flex with MyFord touch without amp 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Flex with MyFord touch without amp 2013-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the shifter bezel (Fig. 1.1) 2. Unclip and remove the trim above the radio and glove box. (Fig. 1.2) Remove two (2) 7mm screws behind the trim. (Fig. 1.3) 3. Remove the panels on each side of the center console, exposing (1) 7mm screw on each side. Remove the two (2) screws. (Fig. 1.4) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 Fig. 1.7 Fig. 1.8 4.
Ford Flex with MyFord touch without amp 2013-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Flex with MyFord touch without amp 2013-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Flex with MyFord touch without amp 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Flex with MyFord touch without amp 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2016 Ford Fusion with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Fusion with MyFord touch with Sony amp 2013-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Fusion with MyFord touch with Sony amp 2013-2016 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the shifter trim panel. (Fig. 1.1) 2. Unclip and remove the U-shaped trim at the rear of shifter. (Fig. 1.2) 3. (2017 and subsequent models ONLY): unclip and remove the side panels of the center console. Remove the screws exposed. (Fig. 1.3) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 4. Unclip and remove the trim surrounding the center dash. (Fig. 1.4) 5.
Ford Fusion with MyFord touch with Sony amp 2013-2016 INSTALLATION INSTRUCTIONS MAKE CONNECTIONS (refer to wiring diagram) DASH KIT ASSEMBLY 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2.
Ford Fusion with MyFord touch with Sony amp 2013-2016 WIRING DIAGRAM STEP 4 STEP 1 RCA CABLES WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP.
Ford Fusion with MyFord touch with Sony amp 2013-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DAT
Ford Fusion with MyFord touch with Sony amp 2013-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2019 Ford Fusion with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Fusion with MyFord touch without amp 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Fusion with MyFord touch without amp 2013-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the shifter trim panel. (Fig. 1.1) 2. Unclip and remove the U-shaped trim at the rear of shifter. (Fig. 1.2) 3. (2017 and subsequent models ONLY): unclip and remove the side panels of the center console. Remove the screws exposed. (Fig. 1.3) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 4. Unclip and remove the trim surrounding the center dash. (Fig. 1.4) 5.
Ford Fusion with MyFord touch without amp 2013-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Fusion with MyFord touch without amp 2013-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Fusion with MyFord touch without amp 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Fusion with MyFord touch without amp 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2019 Ford Mustang with MyFord touch with B&O system RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Mustang with MyFord touch with B&O system 2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Mustang with MyFord touch with B&O system 2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Open the passenger door. Unclip and remove trim panel from the side of dash. (Fig. 1.1-A) 2. Open the glove box. Unclip and remove trim panel on the right. (Fig. 1.1-B) 3. Unclip and remove the (vent) dash panel. (Fig. 1.1-C) 4. Remove the tray cover in front of shifter and remove the two (2) 7mm screws. (Fig.1.2) Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.
Ford Mustang with MyFord touch with B&O system 2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Mustang with MyFord touch with B&O system 2019 WIRING DIAGRAM STEP 4 STEP 1 RCA CABLES WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP.
Ford Mustang with MyFord touch with B&O system 2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Mustang with MyFord touch with B&O system 2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2015-2019 Ford Mustang with MyFord touch with Shaker amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Mustang with MyFord touch with Shaker amp 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Mustang with MyFord touch with Shaker amp 2015-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Open the passenger door. Unclip and remove trim panel from the side of dash. (Fig. 1.1-A) 2. Open the glove box. Unclip and remove trim panel on the right. (Fig. 1.1-B) 3. Unclip and remove the (vent) dash panel. (Fig. 1.1-C) 4. Remove the tray cover in front of shifter and remove the two (2) 7mm screws. (Fig.1.2) Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.
Ford Mustang with MyFord touch with Shaker amp 2015-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Mustang with MyFord touch with Shaker amp 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 RCA CABLES WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP.
Ford Mustang with MyFord touch with Shaker amp 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (
Ford Mustang with MyFord touch with Shaker amp 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2015-2019 Ford Mustang with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Mustang with MyFord touch without amp 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Mustang with MyFord touch without amp 2015-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Open the passenger door. Unclip and remove trim panel from the side of dash. (Fig. 1.1-A) 2. Open the glove box. Unclip and remove trim panel on the right. (Fig. 1.1-B) 3. Unclip and remove the (vent) dash panel. (Fig. 1.1-C) 4. Remove the tray cover in front of shifter and remove the two (2) 7mm screws. (Fig.1.2) Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.
Ford Mustang with MyFord touch without amp 2015-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Mustang with MyFord touch without amp 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Mustang with MyFord touch without amp 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA
Ford Mustang with MyFord touch without amp 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2019-2020 Ford Ranger with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Ranger with MyFord touch without amp 2019-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Ranger with MyFord touch without amp 2019-2020 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the passenger side vent and dash panel assembly. (Fig. 1.1) 2. Unclip and remove the vent to the left of the radio. (Fig. 1.2) 3. Unclip and remove the lower trim panels to the left and right of the climate controls. (Fig. 1.3) 4. Unclip and remove the lower dash panel. (Fig. 1.4) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 Fig. 1.7 Fig. 1.8 5.
Ford Ranger with MyFord touch without amp 2019-2020 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Drill out the pop-rivet on the OEM radio bracket so that it will sit flat against the MFT1 brackets (arrow Fig 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Ranger with MyFord touch without amp 2019-2020 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Ranger with MyFord touch without amp 2019-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Ranger with MyFord touch without amp 2019-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2019 Ford Taurus with MyFord touch with Sony amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Taurus with MyFord touch with Sony amp 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Taurus with MyFord touch with Sony amp 2013-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: Requires shallow mount radio. 1. Unclip and remove the two (2) trim panels on the sides of the center console. (Fig. 1.1-A) 2. Unclip and remove the dash trim panel (right of passenger a/c vent). (Fig. 1.1-B) 3. Unclip and remove the knee bolster panel (below steering column). (Fig. 1.1-C) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 Fig. 1.7 Fig. 1.8 4.
Ford Taurus with MyFord touch with Sony amp 2013-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the MFT1 T-harness and match the wire functions (refer to diagram). 2.
Ford Taurus with MyFord touch with Sony amp 2013-2019 WIRING DIAGRAM STEP 4 STEP 1 RCA CABLES WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT RR RCA INPUT BLUE/WHITE - AMP.
Ford Taurus with MyFord touch with Sony amp 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DAT
Ford Taurus with MyFord touch with Sony amp 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
INSTALL GUIDE 2013-2019 Ford Taurus with MyFord touch without amp RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro MFT1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Taurus with MyFord touch without amp 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Taurus with MyFord touch without amp 2013-2019 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY NOTE: Requires shallow mount radio. 1. Unclip and remove the two (2) trim panels on the sides of the center console. (Fig. 1.1-A) 2. Unclip and remove the dash trim panel (right of passenger a/c vent). (Fig. 1.1-B) 3. Unclip and remove the knee bolster panel (below steering column). (Fig. 1.1-C) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 Fig. 1.7 Fig. 1.8 4.
Ford Taurus with MyFord touch without amp 2013-2019 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY MAKE CONNECTIONS (refer to wiring diagram) 1. Attach the brackets supplied with the MFT1 to the aftermarket radio (use set #1 or #2, see previous page). 2. Remove the mounting brackets from the OEM screen and attach them to MFT1 brackets (Example: Fig. 2.0). 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Ford Taurus with MyFord touch without amp 2013-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Taurus with MyFord touch without amp 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green VSS (vehicle speed sensor) (DATA)
Ford Taurus with MyFord touch without amp 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION The radio is not turning on. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the supplied 54-pin connector is plugged into the vehicle, and that the 18-pin connector on the other end is connected to the Maestro module. Reset the RR.
