SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE 2012-2014 Ford Focus with 4.3" MyFord screen RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FOC1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Focus with 4.3" MyFord screen 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Focus with 4.3" MyFord screen 2012-2014 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Pry off center cap at the bottom of the factory radio bezel to expose two (2) screws. (Fig. 1.1) 2. Remove two (2) Torx T25 screws. (Fig. 1.2) 3. Starting at the bottom, pull the bezel forward. At the same time, use a panel removal tool to pry the bezel. (Fig. 1.3) Disconnect the connector at the back of the bezel and put it to the side. Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 4.
Ford Focus with 4.3" MyFord screen 2012-2014 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY 1. Attach the pocket of the FOC1 to the bezel using the four (4) provided screws. (Fig. 2.1) NOTE: If the pocket sticks when opening or closing, you can adjust the fit by loosening the screws that secure the pocket by 1/4 turn until the pocket no longer sticks. 2. Install the combination hazard/lock switch into the FOC1 bezel (the other hazard switch is not used). (Fig. 2.2) Fig. 2.1 Fig. 2.2 Fig. 2.3 Fig. 2.4 Fig.
Ford Focus with 4.3" MyFord screen 2012-2014 INSTALLATION INSTRUCTIONS MAKE CONNECTIONS (refer to wiring diagram) 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect the wires from the aftermarket radio’s main harness to the FOC1 t-harness and match the wire functions (refer to diagram). 2. Connect the FOC1 T-harness to the factory radio harness. Plug the backup camera cable into the factory harness (if applicable). 3.
Ford Focus with 4.3" MyFord screen 2012-2014 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Focus with 4.
Ford Focus with 4.3" MyFord screen 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the BROWN/RED and BROWN/YELLOW wires are connected to the OBDII (NOT the red/brown and yellow/brown wires). Check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2015-2018 Ford Focus with 4.3" MyFord screen RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FOC1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Focus with 4.3" MyFord screen 2015-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Focus with 4.3" MyFord screen 2015-2018 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the trim panel at the bottom of the factory bezel (this panel contains the airbag light). (Fig. 1.1) 2. Remove the trim around the shifter console by prying it up and unclipping it. (Fig. 1.2) 3. Remove three (3) phillips screws holding the shifter surround and climate controls. (Fig. 1.3) 4. Remove two (2) Torx T25 screws at the bottom of the bezel. (Fig. 1.4) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.
Ford Focus with 4.3" MyFord screen 2015-2018 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY 1. Attach the pocket of the FOC1 to the bezel using the four (4) provided screws. (Fig. 2.1) NOTE: If the pocket sticks when opening or closing, you can adjust the fit by loosening the screws that secure the pocket by 1/4 turn until the pocket no longer sticks. 2. Remove the bezel that is attached to the bottom of the FOC1. Using the screws provided, attach the bottom bezel trim that matches the factory bezel. (Fig. 2.
Ford Focus with 4.3" MyFord screen 2015-2018 INSTALLATION INSTRUCTIONS MAKE CONNECTIONS (refer to wiring diagram) 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect the wires from the aftermarket radio’s main harness to the FOC1 t-harness and match the wire functions (refer to diagram). 2. Connect the FOC1 T-harness to the factory radio harness. Plug the backup camera cable into the factory harness (if applicable). Fig. 2.1 Fig. 2.2 3.
Ford Focus with 4.3" MyFord screen 2015-2018 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Focus with 4.
Ford Focus with 4.3" MyFord screen 2015-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the BROWN/RED and BROWN/YELLOW wires are connected to the OBDII (NOT the red/brown and yellow/brown wires). Check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2012-2014 Ford Focus with 8" MyFord touch screen and base audio system RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FOC1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Focus with 8" MyFord touch screen and base audio system 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Focus with 8" MyFord touch screen and base audio system 2012-2014 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Pry off center cap at the bottom of the factory radio bezel to expose two (2) screws. (Fig. 1.1) 2. Remove two (2) Torx T25 screws. (Fig. 1.2) 3. Starting at the bottom, pull the bezel forward. At the same time, use a panel removal tool to pry the bezel. (Fig. 1.3) Disconnect the connector at the back of the bezel and put it to the side. Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.
Ford Focus with 8" MyFord touch screen and base audio system 2012-2014 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY 1. Attach the pocket of the FOC1 to the bezel using the four (4) provided screws. (Fig. 2.1) NOTE: If the pocket sticks when opening or closing, you can adjust the fit by loosening the screws that secure the pocket by 1/4 turn until the pocket no longer sticks. 2. Install the combination hazard/lock switch into the FOC1 bezel (the other hazard switch is not used). (Fig. 2.2) Fig. 2.1 Fig. 2.
Ford Focus with 8" MyFord touch screen and base audio system 2012-2014 INSTALLATION INSTRUCTIONS MAKE CONNECTIONS (refer to wiring diagram) 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect the wires from the aftermarket radio’s main harness to the FOC1 t-harness and match the wire functions (refer to diagram). 2. Connect the FOC1 T-harness to the factory radio harness. Plug the backup camera cable into the factory harness (if applicable). 3.
Ford Focus with 8" MyFord touch screen and base audio system 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Focus with 8" MyFord touch screen and base audio system 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+)
Ford Focus with 8" MyFord touch screen and base audio system 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the BROWN/RED and BROWN/YELLOW wires are connected to the OBDII (NOT the red/brown and yellow/brown wires). Check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
INSTALL GUIDE 2015-2018 Ford Focus with 8" MyFord touch screen and base audio system RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FOC1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Focus with 8" MyFord touch screen and base audio system 2015-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Focus with 8" MyFord touch screen and base audio system 2015-2018 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the trim panel at the bottom of the factory bezel (this panel contains the airbag light). (Fig. 1.1) 2. Remove the trim around the shifter console by prying it up and unclipping it. (Fig. 1.2) 3. Remove three (3) phillips screws holding the shifter surround and climate controls. (Fig. 1.3) 4. Remove two (2) Torx T25 screws at the bottom of the bezel. (Fig. 1.4) Fig. 1.
Ford Focus with 8" MyFord touch screen and base audio system 2015-2018 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY 1. Attach the pocket of the FOC1 to the bezel using the four (4) provided screws. (Fig. 2.1) NOTE: If the pocket sticks when opening or closing, you can adjust the fit by loosening the screws that secure the pocket by 1/4 turn until the pocket no longer sticks. 2. Remove the bezel that is attached to the bottom of the FOC1.
Ford Focus with 8" MyFord touch screen and base audio system 2015-2018 INSTALLATION INSTRUCTIONS MAKE CONNECTIONS (refer to wiring diagram) 1. Locate the aftermarket radio’s main harness. Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect the wires from the aftermarket radio’s main harness to the FOC1 t-harness and match the wire functions (refer to diagram). Fig. 2.1 Fig. 2.2 2. Connect the FOC1 T-harness to the factory radio harness.
Ford Focus with 8" MyFord touch screen and base audio system 2015-2018 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Ford Focus with 8" MyFord touch screen and base audio system 2015-2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+)
Ford Focus with 8" MyFord touch screen and base audio system 2015-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the BROWN/RED and BROWN/YELLOW wires are connected to the OBDII (NOT the red/brown and yellow/brown wires). Check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
INSTALL GUIDE 2012-2014 Ford Focus with 8" MyFord touch screen and Sony audio system RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FOC1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Focus with 8" MyFord touch screen and Sony audio system 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Focus with 8" MyFord touch screen and Sony audio system 2012-2014 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Pry off center cap at the bottom of the factory radio bezel to expose two (2) screws. (Fig. 1.1) 2. Remove two (2) Torx T25 screws. (Fig. 1.2) 3. Starting at the bottom, pull the bezel forward. At the same time, use a panel removal tool to pry the bezel. (Fig. 1.3) Disconnect the connector at the back of the bezel and put it to the side. Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.
Ford Focus with 8" MyFord touch screen and Sony audio system 2012-2014 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY 1. Attach the pocket of the FOC1 to the bezel using the four (4) provided screws. (Fig. 2.1) NOTE: If the pocket sticks when opening or closing, you can adjust the fit by loosening the screws that secure the pocket by 1/4 turn until the pocket no longer sticks. 2. Install the combination hazard/lock switch into the FOC1 bezel (the other hazard switch is not used). (Fig. 2.2) Fig. 2.1 Fig. 2.
Ford Focus with 8" MyFord touch screen and Sony audio system 2012-2014 INSTALLATION INSTRUCTIONS MAKE CONNECTIONS (refer to wiring diagram) 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to the FOC1 t-harness and match the wire functions (refer to diagram). 2. Assemble and connect the FOC1 T-harness to the factory radio harness. Plug the backup camera cable into the factory harness (if applicable). 3.
Ford Focus with 8" MyFord touch screen and Sony audio system 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 RCA CABLES WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
Ford Focus with 8" MyFord touch screen and Sony audio system 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+)
Ford Focus with 8" MyFord touch screen and Sony audio system 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the BROWN/RED and BROWN/YELLOW wires are connected to the OBDII (NOT the red/brown and yellow/brown wires). Check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
INSTALL GUIDE 2015-2018 Ford Focus with 8" MyFord touch screen and Sony audio system RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro FOC1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-FOR02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Ford Focus with 8" MyFord touch screen and Sony audio system 2015-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Ford Focus with 8" MyFord touch screen and Sony audio system 2015-2018 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY 1. Unclip and remove the trim panel at the bottom of the factory bezel (this panel contains the airbag light). (Fig. 1.1) 2. Remove the trim around the shifter console by prying it up and unclipping it. (Fig. 1.2) 3. Remove three (3) phillips screws holding the shifter surround and climate controls. (Fig. 1.3) 4. Remove two (2) Torx T25 screws at the bottom of the bezel. (Fig. 1.4) Fig. 1.
Ford Focus with 8" MyFord touch screen and Sony audio system 2015-2018 INSTALLATION INSTRUCTIONS DASH KIT ASSEMBLY 1. Attach the pocket of the FOC1 to the bezel using the four (4) provided screws. (Fig. 2.1) NOTE: If the pocket sticks when opening or closing, you can adjust the fit by loosening the screws that secure the pocket by 1/4 turn until the pocket no longer sticks. 2. Remove the bezel that is attached to the bottom of the FOC1.
Ford Focus with 8" MyFord touch screen and Sony audio system 2015-2018 INSTALLATION INSTRUCTIONS MAKE CONNECTIONS (refer to wiring diagram) 1. Locate the aftermarket radio’s main harness. Connect the wires from the aftermarket radio’s main harness to Fig. 2.1 Fig. 2.2 the FOC1 t-harness and match the wire functions (refer to diagram). 2. Assemble and connect the FOC1 T-harness to the factory radio harness. Plug the backup camera cable into the factory harness (if applicable). 3.
Ford Focus with 8" MyFord touch screen and Sony audio system 2015-2018 WIRING DIAGRAM STEP 4 STEP 1 RCA CABLES WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
Ford Focus with 8" MyFord touch screen and Sony audio system 2015-2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+)
Ford Focus with 8" MyFord touch screen and Sony audio system 2015-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the BROWN/RED and BROWN/YELLOW wires are connected to the OBDII (NOT the red/brown and yellow/brown wires). Check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
QUICK START GUIDE FOR CAR RADIO INSTALLATION KITS GUIDE DE DEMARRAGE RAPIDE POUR KITS D'INSTALLATION AUTO RADIO GUIA DE INICIO RAPIDO PARA KITS DE INSTALACION DE AUTORRADIO ]_[ 0'\ S2 !:'-. ........
WEB-PROGRAMMING STEPS ETAPES DE PROGRAMMATION WEB ~ THIS PRODUCT REQUIRES THE INSTALLATION OF ~ AMAESTRO RR (ADS-MRR] MODULE SOLD SEPARATELY ~ CE PRODUIT NECESSITE L'INSTALLATION,D'UN MODULE ~ MAESTRO RR [ADS-MRRI VENDU SEPAREMENT CD CD PASOS DE PROGRAMACION WEB ~ ESTE PRODUCTO REQUIERE LAINSTALACION DEL MODULO ~ MAESTRO RR [ADS-MRRI VENOIDOPOR SEPARADO CD INSTALLEZ LE PLUG IN WEB LINK (PC SEULEMENT) Allez a idatalinkmaestro.com/plugin et suivez les eta pes d"installation .
LIMITED 1-YEAR WARRANTY Automotive Data Solutions Inc. ("ADS") warrants to the original purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances, for the period of one (1) year as of the original date of purchase. In the event of any product malfunction during the Warranty period, the original purchaser must return to the Authorized Dealer where it was originally purchased with the original proof of purchase.
GARANTIA LIMITADA POR 1ANO Automotive Data Solutions Inc. ("ADS") garantiza al comprador original que este producto no presentara ningun defecto relacionado con sus materiales o su fabricaci6n, bajo condiciones normales de uso, durante un (1) a no a partir de La fecha original de compra. En caso de que el producto presente alguna falla durante el perfodo de Garantfa, el comprador original debera remitirse al Distribuidor Autorizado donde to cornpr6, llevando consigo La prueba de compra original.
~estro CAR RADIO INSTALLATION KIT KIT D'INSTAllATION AUTORADIO KIT DE INSTALAC/ON PARA AUTORRAD/0 FORD FOCUS 2012-2018 ALL TRIMS I TOUS MODlLES I TODOS MODELOS Part #I No. Piece INo.
9EM grade fit and finish ffuaUte .
Harnais d'installaUon -Amis de caiJleado RADIO PANEL Panneau de radio - Panel fmntal del radi(J 2D12·2U14TRIM KIT Kit de gamiblre 21Jl2-28" ·'Kll de ajllste1012-2DU
