SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE 2010-2015 Chevrolet Camaro with AMP RETAINS HEADS UP DISPLAY, STEERING WHEEL CONTROLS AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CAM1 Dash Kit E L E C T R O N I C S PROGRAMMED FIRMWARE Click here for: Radar Integration Installation Guide Radar Integration Owner’s Guide for Kenwood and JVC Radios ADS-RR(SR)-GM02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide CAM1 Dash Kit Installation Vi
Chevrolet Camaro with AMP 2010-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Chevrolet Camaro with AMP 2010-2015 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY (Center console removal) Note: It is not possible to install the CAM1 dash kit and aftermarket radio without removing the center console. 1. Engage the parking brake. Put the shifter all the way back. (Fig. 1.1) 2. Pry upward and remove the center console trim. Unclip the center console wiring harnesses and remove it. (Fig. 1.2) 3.
Chevrolet Camaro with AMP 2010-2015 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY (Radio removal) 3. Connect the CAM1 T-harness to the factory radio harness. 1. Remove (2) 7mm screws securing the bottom of the radio bezel. (Fig. 2.1) 4. Plug the OBD2 connector into the OBD2 port of the vehicle, located under the driver side dash. 2. Using a panel tool, gently release the clips securing the radio bezel to the dash. Disconnect the wiring harness on the back of the OEM panel. (Fig. 2.1) 5.
Chevrolet Camaro with AMP 2010-2015 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Chevrolet Camaro with AMP 2010-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N/A
Chevrolet Camaro with AMP 2010-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio’s serial number entered during the flash matches what is listed on the radio screen.
INSTALL GUIDE 2010-2015 Chevrolet Camaro without AMP RETAINS HEADS UP DISPLAY, STEERING WHEEL CONTROLS AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CAM1 Dash Kit E L E C T R O N I C S PROGRAMMED FIRMWARE Click here for: Radar Integration Installation Guide Radar Integration Owner’s Guide for Kenwood and JVC Radios ADS-RR(SR)-GM02C-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide CAM1 Dash Kit Installation
Chevrolet Camaro without AMP 2010-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Chevrolet Camaro without AMP 2010-2015 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY (Center console removal) Note: It is not possible to install the CAM1 dash kit and aftermarket radio without removing the center console. 1. Engage the parking brake. Put the shifter all the way back. (Fig. 1.1) 2. Pry upward and remove the center console trim. Unclip the center console wiring harnesses and remove it. (Fig. 1.2) 3.
Chevrolet Camaro without AMP 2010-2015 INSTALLATION INSTRUCTIONS DASH DISASSEMBLY (Radio removal) 3. Connect the CAM1 T-harness to the factory radio harness. 1. Remove (2) 7mm screws securing the bottom of the radio bezel. (Fig. 2.1) 4. Plug the OBD2 connector into the OBD2 port of the vehicle, located under the driver side dash. 2. Using a panel tool, gently release the clips securing the radio bezel to the dash. Disconnect the wiring harness on the back of the OEM panel. (Fig. 2.1) 5.
Chevrolet Camaro without AMP 2010-2015 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Chevrolet Camaro without AMP 2010-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N/
Chevrolet Camaro without AMP 2010-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio’s serial number entered during the flash matches what is listed on the radio screen.
LIMITED 1-YEAR WARRANTY GARANTIA LIMITADA POR 1ANO Automotive Data Solutions Inc. (""ADS ") warrants to the original purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances, for the period of one (1) year as of the original date of purchase. Automotive Data Solutions Inc.
WEB-PROGRAMMING STEPS ETAPES DE PROGRAMMATION WEB ~ THISPRODUCTREQUIRES THE INSTALLATION OF ~ AMAESTRO RR [ADS-MRR] MODULE SOLD SEPARATELY ~ CE PRODUIT NECESSITE L'INSTALLATION,D'UN MODULE ~ MAESTRO RR [ADS-MRR] VENDU SEPAREMENT PASOSDE PROGRAMACION WEB ~ ESTE PRODUCTO REOUIERE LA INSTALACION DEL MODULO ~ MAESTRO RR (ADS-MRR) VEN DIDO POR SEPARADO CD INSTALL THE WEBLINK PLUGIN [FOR PC ONLY) Go to idatalinkmaestro.com/plugin and follow the installation steps.
