Owner's Manual

ManualsBrandsiDatalink ManualsAudio accessories & installationHRN-RR-TO3

Table Of Contents

Install Guide

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certiﬁ ed technician. Logos and trademarks used here in

are the properties of their respective owners.

WARNING

Pressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll

down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced

options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE

SELECT VEHICLE

PRINT PAGES NEEDED

Summary of content (151 pages)

PAGE 1
SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
PAGE 2
INSTALL GUIDE 2020 Toyota 4 Runner With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 3
Toyota 4 Runner With JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 4
Toyota 4 Runner With JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 5
Toyota 4 Runner With JBL 2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 6
Toyota 4 Runner With JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N
PAGE 7
Toyota 4 Runner With JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 8
INSTALL GUIDE 2020 Toyota 4 Runner Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 9
Toyota 4 Runner Without JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 10
Toyota 4 Runner Without JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 11
Toyota 4 Runner Without JBL 2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 12
Toyota 4 Runner Without JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 13
Toyota 4 Runner Without JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 14
INSTALL GUIDE 2019-2020 Toyota Avalon With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 15
Toyota Avalon With JBL 2019-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 16
Toyota Avalon With JBL 2019-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 17
Toyota Avalon With JBL 2019-2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 18
Toyota Avalon With JBL 2019-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 19
Toyota Avalon With JBL 2019-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 20
INSTALL GUIDE 2019-2020 Toyota Avalon Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 21
Toyota Avalon Without JBL 2019-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 22
Toyota Avalon Without JBL 2019-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 23
Toyota Avalon Without JBL 2019-2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 24
Toyota Avalon Without JBL 2019-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
PAGE 25
Toyota Avalon Without JBL 2019-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 26
INSTALL GUIDE 2018 Toyota C-HR With CarPlay With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 27
Toyota C-HR With CarPlay With JBL 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 28
Toyota C-HR With CarPlay With JBL 2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 29
Toyota C-HR With CarPlay With JBL 2018 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 30
Toyota C-HR With CarPlay With JBL 2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄
PAGE 31
Toyota C-HR With CarPlay With JBL 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 32
INSTALL GUIDE 2018 Toyota C-HR With CarPlay Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 33
Toyota C-HR With CarPlay Without JBL 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 34
Toyota C-HR With CarPlay Without JBL 2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 35
Toyota C-HR With CarPlay Without JBL 2018 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 36
Toyota C-HR With CarPlay Without JBL 2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black
PAGE 37
Toyota C-HR With CarPlay Without JBL 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 38
INSTALL GUIDE 2019-2020 Toyota C-HR With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 39
Toyota C-HR With JBL 2019-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 40
Toyota C-HR With JBL 2019-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 41
Toyota C-HR With JBL 2019-2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 42
Toyota C-HR With JBL 2019-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 43
Toyota C-HR With JBL 2019-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 44
INSTALL GUIDE 2019-2020 Toyota C-HR Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 45
Toyota C-HR Without JBL 2019-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 46
Toyota C-HR Without JBL 2019-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 47
Toyota C-HR Without JBL 2019-2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 48
Toyota C-HR Without JBL 2019-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
PAGE 49
Toyota C-HR Without JBL 2019-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 50
INSTALL GUIDE 2018-2020 Toyota Camry With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 51
Toyota Camry With JBL 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 52
Toyota Camry With JBL 2018-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 53
Toyota Camry With JBL 2018-2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 54
Toyota Camry With JBL 2018-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 55
Toyota Camry With JBL 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 56
INSTALL GUIDE 2018-2020 Toyota Camry Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 57
Toyota Camry Without JBL 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 58
Toyota Camry Without JBL 2018-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 59
Toyota Camry Without JBL 2018-2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 60
Toyota Camry Without JBL 2018-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
PAGE 61
Toyota Camry Without JBL 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 62
INSTALL GUIDE 2020 Toyota Corolla With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 63
Toyota Corolla With JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 64
Toyota Corolla With JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 65
Toyota Corolla With JBL 2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 66
Toyota Corolla With JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/
PAGE 67
Toyota Corolla With JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 68
INSTALL GUIDE 2020 Toyota Corolla Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 69
Toyota Corolla Without JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 70
Toyota Corolla Without JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 71
Toyota Corolla Without JBL 2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 72
Toyota Corolla Without JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 73
Toyota Corolla Without JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 74
INSTALL GUIDE 2020 Toyota Highlander With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 75
Toyota Highlander With JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 76
Toyota Highlander With JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 77
Toyota Highlander With JBL 2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 78
Toyota Highlander With JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 79
Toyota Highlander With JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 80
INSTALL GUIDE 2020 Toyota Highlander Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 81
Toyota Highlander Without JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 82
Toyota Highlander Without JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 83
Toyota Highlander Without JBL 2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 84
Toyota Highlander Without JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
PAGE 85
Toyota Highlander Without JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 86
INSTALL GUIDE 2019-2020 Toyota Rav4 With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 87
Toyota Rav4 With JBL 2019-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 88
Toyota Rav4 With JBL 2019-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 89
Toyota Rav4 With JBL 2019-2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 90
Toyota Rav4 With JBL 2019-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 91
Toyota Rav4 With JBL 2019-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 92
INSTALL GUIDE 2019-2020 Toyota Rav4 Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 93
Toyota Rav4 Without JBL 2019-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 94
Toyota Rav4 Without JBL 2019-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 95
Toyota Rav4 Without JBL 2019-2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 96
Toyota Rav4 Without JBL 2019-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
PAGE 97
Toyota Rav4 Without JBL 2019-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 98
INSTALL GUIDE 2020 Toyota Sequoia With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 99
Toyota Sequoia With JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 100
Toyota Sequoia With JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 101
Toyota Sequoia With JBL 2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 102
Toyota Sequoia With JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/
PAGE 103
Toyota Sequoia With JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 104
INSTALL GUIDE 2020 Toyota Sequoia Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 105
Toyota Sequoia Without JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 106
Toyota Sequoia Without JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 107
Toyota Sequoia Without JBL 2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 108
Toyota Sequoia Without JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 109
Toyota Sequoia Without JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 110
INSTALL GUIDE 2018-2020 Toyota Sienna With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 111
Toyota Sienna With JBL 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 112
Toyota Sienna With JBL 2018-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle (under driver dash).
PAGE 113
Toyota Sienna With JBL 2018-2020 WIRING DIAGRAM with JBL STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 114
Toyota Sienna With JBL 2018-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 115
Toyota Sienna With JBL 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 116
INSTALL GUIDE 2018-2020 Toyota Sienna Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 117
Toyota Sienna Without JBL 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 118
Toyota Sienna Without JBL 2018-2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 119
Toyota Sienna Without JBL 2018-2020 WIRING DIAGRAM without JBL STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 120
Toyota Sienna Without JBL 2018-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
PAGE 121
Toyota Sienna Without JBL 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 122
INSTALL GUIDE 2020 Toyota Tacoma With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 123
Toyota Tacoma With JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 124
Toyota Tacoma With JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 125
Toyota Tacoma With JBL 2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 126
Toyota Tacoma With JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
PAGE 127
Toyota Tacoma With JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 128
INSTALL GUIDE 2020 Toyota Tacoma Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 129
Toyota Tacoma Without JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 130
Toyota Tacoma Without JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 131
Toyota Tacoma Without JBL 2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 132
Toyota Tacoma Without JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 133
Toyota Tacoma Without JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 134
INSTALL GUIDE 2020 Toyota Tundra With JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 135
Toyota Tundra With JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 136
Toyota Tundra With JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness. STEP 3 • Plug the aftermarket radio harnesses into the aftermarket radio.
PAGE 137
Toyota Tundra With JBL 2020 WIRING DIAGRAM with JBL STEP 3 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
PAGE 138
Toyota Tundra With JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
PAGE 139
Toyota Tundra With JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 140
INSTALL GUIDE 2020 Toyota Tundra With Non-JBL Amp RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 141
Toyota Tundra With Non-JBL Amp 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 142
Toyota Tundra With Non-JBL Amp 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 143
Toyota Tundra With Non-JBL Amp 2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 144
Toyota Tundra With Non-JBL Amp 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
PAGE 145
Toyota Tundra With Non-JBL Amp 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.
PAGE 146
INSTALL GUIDE 2020 Toyota Tundra Without JBL RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO3 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 147
Toyota Tundra Without JBL 2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 148
Toyota Tundra Without JBL 2020 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO3 T-harness and match the wire functions (Note: Rear speaker wire connections are not required). • Remove the factory radio. STEP 2 • Connect the factory harness to the TO3 T-harness.
PAGE 149
Toyota Tundra Without JBL 2020 WIRING DIAGRAM without JBL STEP 3 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 150
Toyota Tundra Without JBL 2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
PAGE 151
Toyota Tundra Without JBL 2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the ﬂash. Verify the radio’s serial number entered during the ﬂash matches what is listed on the radio screen.