SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE 2014-2019 Toyota 4 Runner With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota 4 Runner With JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota 4 Runner With JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota 4 Runner With JBL 2014-2019 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota 4 Runner With JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota 4 Runner With JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota 4 Runner With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota 4 Runner Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota 4 Runner Without JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota 4 Runner Without JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota 4 Runner Without JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner Without JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota 4 Runner Without JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota 4 Runner Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Avalon With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Avalon With JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Avalon With JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Avalon With JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Avalon With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2013-2014 Toyota Avalon With NAV With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon With NAV With JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With NAV With JBL 2013-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Avalon With NAV With JBL 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Avalon With NAV With JBL 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black
Toyota Avalon With NAV With JBL 2013-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Avalon With NAV With JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2013-2014 Toyota Avalon With NAV Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon With NAV Without JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With NAV Without JBL 2013-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Avalon With NAV Without JBL 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With NAV Without JBL 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Bla
Toyota Avalon With NAV Without JBL 2013-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Avalon With NAV Without JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Avalon Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon Without JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Avalon Without JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon Without JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Avalon Without JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Avalon Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2018 Toyota C-HR Without Apple Carplay or Android Auto RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota C-HR Without Apple Carplay or Android Auto 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota C-HR Without Apple Carplay or Android Auto 2018 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota C-HR Without Apple Carplay or Android Auto 2018 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota C-HR Without Apple Carplay or Android Auto 2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black
Toyota C-HR Without Apple Carplay or Android Auto 2018 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota C-HR Without Apple Carplay or Android Auto 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Camry With Factory 6.1 inch Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory 6.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Camry With Factory 6.1 inch Screen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Camry With Factory 6.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Camry With Factory Screen and HDD and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Bla
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2017 Toyota Camry With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry With JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With JBL 2015-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Camry With JBL 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Camry With JBL 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Camry With JBL 2015-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Camry With JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2015-2017 Toyota Camry Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry Without JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry Without JBL 2015-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Camry Without JBL 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry Without JBL 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Camry Without JBL 2015-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Camry Without JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Corolla With Factory 6.1 inch Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Corolla With Factory 6.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Highlander With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Highlander With JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Highlander With JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Highlander With JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Highlander With JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Highlander With JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Highlander With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Highlander Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Highlander Without JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Highlander Without JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Highlander Without JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander Without JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N
Toyota Highlander Without JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Highlander Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2016-2019 Toyota Prius Base RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius Base 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius Base 2016-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius Base 2016-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius Base 2016-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
Toyota Prius Base 2016-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius Base 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2015-2019 Toyota Prius C With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius C With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius C With JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota Prius C With JBL 2015-2019 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Prius C With JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Prius C With JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius C With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Prius C Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius C Without JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius C Without JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius C Without JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C Without JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Prius C Without JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius C Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Prius C Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius C Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius C Without JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius C Without JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C Without JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Prius C Without JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius C Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Prius V With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius V With JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius V With JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota Prius V With JBL 2012-2014 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Prius V With JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Prius V With JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius V With JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2017 Toyota Prius V With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius V With JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius V With JBL 2015-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota Prius V With JBL 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Prius V With JBL 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Prius V With JBL 2015-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius V With JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Prius V Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius V Without JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius V Without JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius V Without JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V Without JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Prius V Without JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius V Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2017 Toyota Prius V Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius V Without JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius V Without JBL 2015-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius V Without JBL 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V Without JBL 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Prius V Without JBL 2015-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius V Without JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Prius With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius With JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota Prius With JBL 2012-2014 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Prius With JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Prius With JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius With JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2015-2019 Toyota Prius With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota Prius With JBL 2015-2019 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Prius With JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Prius With JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2012-2014 Toyota Prius With Nav Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius With Nav Without JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With Nav Without JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius With Nav Without JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With Nav Without JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Blac
Toyota Prius With Nav Without JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius With Nav Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Prius With Nav Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius With Nav Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With Nav Without JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius With Nav Without JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With Nav Without JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Blac
Toyota Prius With Nav Without JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Prius With Nav Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2013-2018 Toyota Rav 4 With Factory 6.1 inch Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 With Factory 6.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2013-2018 Toyota Rav 4 With Factory 6.1 inch Screen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Rav 4 With Factory 6.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2017 Toyota Sequoia With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sequoia With JBL 2014-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sequoia With JBL 2014-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: on Pioneer radio, ensure that there is nothing plugged into the W/R port. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen.
Toyota Sequoia With JBL 2014-2017 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Sequoia With JBL 2014-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Sequoia With JBL 2014-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Sequoia With JBL 2014-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2018-2019 Toyota Sequoia With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sequoia With JBL 2018-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sequoia With JBL 2018-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Sequoia With JBL 2018-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Sequoia With JBL 2018-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Sequoia With JBL 2018-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Sequoia With JBL 2018-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Sienna With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sienna With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sienna With JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota Sienna With JBL 2015-2019 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Sienna With JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Sienna With JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Sienna With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2015-2019 Toyota Sienna Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sienna Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sienna Without JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Sienna Without JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna Without JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Sienna Without JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Sienna Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2016-2019 Toyota Tacoma With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tacoma With JBL 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tacoma With JBL 2016-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Tacoma With JBL 2016-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Tacoma With JBL 2016-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Tacoma With JBL 2016-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Tacoma With JBL 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2016-2019 Toyota Tacoma Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tacoma Without JBL 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tacoma Without JBL 2016-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 5 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Tacoma Without JBL 2016-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma Without JBL 2016-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Tacoma Without JBL 2016-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Tacoma Without JBL 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Tundra With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tundra With JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tundra With JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota Tundra With JBL 2014-2019 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Tundra With JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Tundra With JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Tundra With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2014-2019 Toyota Tundra With non-JBL AMP RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tundra With non-JBL AMP 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tundra With non-JBL AMP 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Tundra With non-JBL AMP 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra With non-JBL AMP 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black
Toyota Tundra With non-JBL AMP 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Tundra With non-JBL AMP 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Tundra Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tundra Without JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tundra Without JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Tundra Without JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra Without JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Tundra Without JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Tundra Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2016 Toyota Venza With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza With JBL 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Venza With JBL 2015-2016 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota Venza With JBL 2015-2016 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Venza With JBL 2015-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Venza With JBL 2015-2016 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Venza With JBL 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2013-2014 Toyota Venza With JBL and Nav RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza With JBL and Nav 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Venza With JBL and Nav 2013-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 Note: For Sony radios with OSD Controllable camera: When the vehicle is equipped with the bird’s eye view camera system, plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter.
Toyota Venza With JBL and Nav 2013-2014 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/BLACK - FOOT BRAKE LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED PURPLE/WHITE - REVERSE LIGHT (+) * PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
Toyota Venza With JBL and Nav 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N
Toyota Venza With JBL and Nav 2013-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Venza With JBL and Nav 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2016 Toyota Venza Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza Without JBL 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Venza Without JBL 2015-2016 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 the only camera input that allows camera control through the touchscreen. • Remove the factory radio STEP 6 If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness.
Toyota Venza Without JBL 2015-2016 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza Without JBL 2015-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Venza Without JBL 2015-2016 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 2 RED flashes Problem detected. Consult troubleshooting table.
Toyota Venza Without JBL 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE 2014-2019 Toyota 4 Runner With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota 4 Runner With JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota 4 Runner With JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota 4 Runner With JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner With JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota 4 Runner With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota 4 Runner Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota 4 Runner Without JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota 4 Runner Without JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota 4 Runner Without JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner Without JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota 4 Runner Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Avalon With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Avalon With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Avalon With JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Avalon With JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Avalon With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2014 Toyota Avalon With NAV With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Avalon With NAV With JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With NAV With JBL 2013-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Avalon With NAV With JBL 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With NAV With JBL 2013-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Avalon With NAV With JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2014 Toyota Avalon With NAV Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Avalon With NAV Without JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With NAV Without JBL 2013-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Avalon With NAV Without JBL 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With NAV Without JBL 2013-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Avalon With NAV Without JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Avalon Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Avalon Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Avalon Without JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Avalon Without JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon Without JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Avalon Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2018 Toyota C-HR Without Apple Carplay or Android Auto RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota C-HR Without Apple Carplay or Android Auto 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota C-HR Without Apple Carplay or Android Auto 2018 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota C-HR Without Apple Carplay or Android Auto 2018 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota C-HR Without Apple Carplay or Android Auto 2018 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota C-HR Without Apple Carplay or Android Auto 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Camry With Factory 6.1 inch Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Camry With Factory 6.1 inch Screen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both).
INSTALL GUIDE 2012-2014 Toyota Camry With Factory Screen and HDD and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both).
INSTALL GUIDE 2015-2017 Toyota Camry With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry With JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Camry With JBL 2015-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Camry With JBL 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With JBL 2015-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Camry With JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2017 Toyota Camry Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry Without JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Camry Without JBL 2015-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Camry Without JBL 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry Without JBL 2015-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Camry Without JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Corolla With Factory 6.1 inch Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Highlander With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Highlander With JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Highlander With JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Highlander With JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander With JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Highlander With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Highlander Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Highlander Without JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Highlander Without JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Highlander Without JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander Without JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Highlander Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2016-2019 Toyota Prius Base RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius Base 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius Base 2016-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Prius Base 2016-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius Base 2016-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius Base 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Prius C With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius C With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius C With JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius C With JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C With JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius C With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius C Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius C Without JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius C Without JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Prius C Without JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C Without JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius C Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Prius C Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius C Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius C Without JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Prius C Without JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C Without JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius C Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius V With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius V With JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius V With JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius V With JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V With JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius V With JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2017 Toyota Prius V With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius V With JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius V With JBL 2015-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius V With JBL 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V With JBL 2015-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius V With JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius V Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius V Without JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius V Without JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Prius V Without JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V Without JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius V Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2017 Toyota Prius V Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius V Without JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius V Without JBL 2015-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Prius V Without JBL 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V Without JBL 2015-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius V Without JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius With JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius With JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius With JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius With JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Prius With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius With JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Prius With JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius With Nav Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius With Nav Without JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With Nav Without JBL 2012-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Prius With Nav Without JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With Nav Without JBL 2012-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius With Nav Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Prius With Nav Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius With Nav Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With Nav Without JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Prius With Nav Without JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With Nav Without JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Prius With Nav Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2018 Toyota Rav 4 With Factory 6.1 inch Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2018 Toyota Rav 4 With Factory 6.1 inch Screen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both).
INSTALL GUIDE 2014-2017 Toyota Sequoia With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Sequoia With JBL 2014-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Sequoia With JBL 2014-2017 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 STEP 6 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. • Connect all the harnesses to the Maestro RR module then test your installation. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Sequoia With JBL 2014-2017 WIRING DIAGRAM STEP 5 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sequoia With JBL 2014-2017 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Sequoia With JBL 2014-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2018-2019 Toyota Sequoia With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Sequoia With JBL 2018-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Sequoia With JBL 2018-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Sequoia With JBL 2018-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sequoia With JBL 2018-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Sequoia With JBL 2018-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Sienna With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Sienna With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Sienna With JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Sienna With JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna With JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Sienna With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Sienna Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Sienna Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Sienna Without JBL 2015-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Sienna Without JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna Without JBL 2015-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Sienna Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2016-2019 Toyota Tacoma With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Tacoma With JBL 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Tacoma With JBL 2016-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Tacoma With JBL 2016-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma With JBL 2016-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Tacoma With JBL 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2016-2019 Toyota Tacoma Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Tacoma Without JBL 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Tacoma Without JBL 2016-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Tacoma Without JBL 2016-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma Without JBL 2016-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Tacoma Without JBL 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Tundra With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Tundra With JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Tundra With JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Tundra With JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra With JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Tundra With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Tundra With non-JBL AMP RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Tundra With non-JBL AMP 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tundra With non-JBL AMP 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Tundra With non-JBL AMP 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra With non-JBL AMP 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Tundra With non-JBL AMP 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Tundra Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Tundra Without JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Tundra Without JBL 2014-2019 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Tundra Without JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra Without JBL 2014-2019 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Tundra Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2016 Toyota Venza With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Venza With JBL 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Venza With JBL 2015-2016 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Venza With JBL 2015-2016 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza With JBL 2015-2016 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Venza With JBL 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2014 Toyota Venza With JBL and Nav RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Venza With JBL and Nav 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Venza With JBL and Nav 2013-2014 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. • Unplug 4 pin white speaker connector and connect RCA adapter. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness.
Toyota Venza With JBL and Nav 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 CONNECTIONS NOT REQUIRED WITH AMP GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza With JBL and Nav 2013-2014 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Venza With JBL and Nav 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2016 Toyota Venza Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HHR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Venza Without JBL 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Module Diagnostics 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Venza Without JBL 2015-2016 INSTALLATION INSTRUCTIONS P1 /1 STEP 1 • Remove the factory radio. If using head unit adapter (sold separately), connect HHRTO2 harness to adapter and skip to step 2. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the black 20 pin connector from the HHRTO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HHRTO2 T-harness and match the wire functions.
Toyota Venza Without JBL 2015-2016 WIRING DIAGRAM STEP 4 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza Without JBL 2015-2016 MODULE DIAGNOSTICS PROGRAMMING BUTTON LED 1 LED 2 LED 1 LED 1 Module/Firmware status LED 2 (RR2) Bluetooth activity LED STATUS DIAGNOSTIC RED or GREEN flashing LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. • 1 RED flash Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. • 1 GREEN flash After radio boots up : Normal operation.
Toyota Venza Without JBL 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
