SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro AR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE Chrysler 200 2015-2016 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Chrysler 200 2015-2016 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Chrysler 200 2015-2016 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Chrysler 200 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Chrysler 200 2015-2016 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN ON
Chrysler 200 2015-2016 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Mid (+) White/Black Left Front Mid (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Mid (+) Gray/Black Right Front Mid (-) 1 Gray Right Front Tweeter (+) Right Front Tweet
HRN-AR-CH2 www.idatalinkmaestro.
INSTALL GUIDE Chrysler 300 2012-2014 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Chrysler 300 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Chrysler 300 2012-2014 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Chrysler 300 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Chrysler 300 2012-2014 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN ON
Chrysler 300 2012-2014 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Gr
INSTALL GUIDE Chrysler 300 2015-2016 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Chrysler 300 2015-2016 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Chrysler 300 2015-2016 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Chrysler 300 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Chrysler 300 2015-2016 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN ON
Chrysler 300 2015-2016 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Gr
INSTALL GUIDE Dodge Challenger 2015-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Dodge Challenger 2015-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Dodge Challenger 2015-2017 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Dodge Challenger 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Dodge Challenger 2015-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TUR
Dodge Challenger 2015-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-)
INSTALL GUIDE Dodge Charger 2012-2014 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Dodge Charger 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Dodge Charger 2012-2014 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Dodge Charger 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Dodge Charger 2012-2014 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN O
Dodge Charger 2012-2014 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) G
INSTALL GUIDE Dodge Charger 2015-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Dodge Charger 2015-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Dodge Charger 2015-2017 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Dodge Charger 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Dodge Charger 2015-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN O
Dodge Charger 2015-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) G
INSTALL GUIDE Dodge Durango 2014-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Dodge Durango 2014-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Dodge Durango 2014-2017 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Dodge Durango 2014-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Dodge Durango 2014-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN O
Dodge Durango 2014-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) G
INSTALL GUIDE Dodge Journey 2011-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Dodge Journey 2011-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Dodge Journey 2011-2017 SETTINGS AND FEATURES MAESTRO AR PROGRAMMABLE FEATURES These tone control features can be adjusted in the settings of the radio. • Bass Tone Control Subwoofer Volume • Mid Tone Control Not applicable • Treble Tone Control Tweeter Output Gain • Surround Control Not applicable • Speed Compensated Volume None 3 Automotive Data Solutions Inc. © 2017 ADS-AR-CHR02 maestro.idatalink.
Dodge Journey 2011-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Dodge Journey 2011-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN O
Dodge Journey 2011-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) G
INSTALL GUIDE Jeep Cherokee 2014-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Jeep Cherokee 2014-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Jeep Cherokee 2014-2017 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Jeep Cherokee 2014-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Jeep Cherokee 2014-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN O
Jeep Cherokee 2014-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Tweeter (+) Green/Black Left Rear Tweeter (-) G
INSTALL GUIDE Jeep Grand Cherokee 2014-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Jeep Grand Cherokee 2014-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Jeep Grand Cherokee 2014-2017 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Jeep Grand Cherokee 2014-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Jeep Grand Cherokee 2014-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP
Jeep Grand Cherokee 2014-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker
INSTALL GUIDE Ram 1500 2013-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Ram 1500 2013-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Ram 1500 2013-2017 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Ram 1500 2013-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Ram 1500 2013-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN ON N.
Ram 1500 2013-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Green
INSTALL GUIDE Ram 2500 & 3500 2013-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro AR Amplifier Replacement Interface iDatalink Maestro AR-CH2 Installation Harness Extension harness provided with Kenwood amplifier ADS-AR-CHR02 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Ram 2500 & 3500 2013-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro AR Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Ram 2500 & 3500 2013-2017 SETTINGS AND FEATURES CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF. If there is no way to turn the radio OFF, set the source to AUX. • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose Medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob.
Ram 2500 & 3500 2013-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the AR-CH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the AR-CH2 T-harness.
Ram 2500 & 3500 2013-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK KENWOOD AMPLIFIER STEP 2 FACTORY AMPLIFIER HARNESSES LEFT FRONT 1 RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 18 PIN CONNECTOR AR-CH2 T-HARNESS AMP TURN
Ram 2500 & 3500 2013-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-)
