PRODUCT GUIDE HCX000A DOCUMENT NUMBER REVISION DATE 20161024 This is a general manual for the remote starter. Download a specific guide from www.idatalink.com NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. U.S.
PAGE 2 OF 12 • 20161024 GETTING STARTED WELCOME Congratulations on the purchase of your iDataStart HC solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your iDataStart HC module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
PAGE 3 OF 12 • 20161024 BOX CONTENTS - 1 OF 1 BOX CONTENTS 2 1 MODULE 4 3 M1 - 8 PIN BLACK 6 5 8 7 AUTOMATIC TRANSMISSION CUT LOOP M2 - 12 PIN BLACK 2 4 6 8 10 12 M5 - 6 PIN BLUE M3 - 10 PIN WHITE M4 - 20 PIN BLACK TELEMATIC 1 - 4 PIN BLUE 1 3 5 7 9 11 M2 01 GREEN•BLACK DOT - LOCK (-) OUTPUT 02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE•BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 GREEN/WHITE•BLACK DOT - ARM (-) OUTPUT 05 GREEN/BLACK•BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE•BLACK DOT - GW
01 TACH PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 12 • 20161024 HCX000A www.idatalink.com START vehicle for 15 seconds. OFF ACC ON START ENGINE START STOP 02 Press and hold the brake pedal. 03 Press and release the module’s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for 2.5 seconds.) 04 Wait, LED 2 will flash GREEN. (See the Module Diagnostics page) 05 Release the brake pedal.
REMOTE PROGRAMMING PROCEDURE - 1 OF 1 01 02 [4x] OFF ACC WARNING: Complete the module programming procedure and tach programming procedure before programming the remotes. A maximum of four [4x] remotes per system. 07 Set ignition to ON position. 08 ON START ENGINE START STOP 03 PAGE 5 OF 12 • 20161024 Release the antenna button. The antenna’s leds will turn OFF. Set ignition to OFF position.
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Valet Mode Programming Procedure completed. 01 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps 1 to 5. 02 PAGE 6 OF 12 • 20161024 Cycle ignition ON twice [2x OFF/ON] rapidly.
PAGE 7 OF 12 • 20161024 COMPATIBLE ACCESSORIES - 1 OF 2 WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (accessory sold separately) OBDII CONNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT 1 2 3 4 5 6 7 8 OBDII CONNECTOR 9 10 11 12 13 14 15 16 TELEMATIC KIT (accessory sold separately) MODULE TELEMATIC BLUE PORT (NC) *For SmartStart, use the module’s RED Telematic port. U.S.
PAGE 8 OF 12 • 20161024 COMPATIBLE ACCESSORIES - 2 OF 2 RF KIT (sold separately) MODULE RF PORT 4 PIN BLACK CABLE ANTENNA U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2016 HCX000A www.idatalink.
ONLINE MODULE SETTINGS - 1 OF 1 WEB PROGRAMMABLE MENUS DESCRIPTION MENU 1 – Remote Starter RS related configuration options MENU 2 – Doorlock Options Convenience feature configuration options MENU 3 – Security Options Alarm activation and settings MENU 4 – AUX function assignments Set transmitter AUX buttons controls MENU 5 – Programmable outputs (POC) Set actions for programmable outputs MENU 6 – Pulse Timer Output Configuration (PTO) Set duration for pulse timer outputs (if used) MENU 7 – I
I II III IV DURING MODULE PROGRAMMING DURING TACH PROGRAMMING DURING REMOTE START WITH IGNITION OFF U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2016 DIAGNOSTIC TEST MODULE LED 1 STATUS MODULE DIAGNOSTICS - 1 OF 1 Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed.
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES - 1 OF 1 I WARNING: The following applies only when the parking lights are connected and supported by the system. 01 Engine running. 02 Key in ignition at ON position. II After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 03 Door is open. 04 Trunk is open. 05 Foot brake is ON. 06 Hood is open.
MODULE RESET PROCEDURE - 1 OF 1 >> The following procedure resets the module programming to the vehicle. It does not reset any settings configured online. 06 Module RESET completed. 01 Disconnect all connectors from module except the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector. 07 Reconnect all connectors. 02 Disconnect the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector. 08 Repeat programming procedure.