Owner's Manual
Table Of Contents
- Chrysler 200 AT 2011-2014
- Chrysler 300 AT 2005-2007
- Chrysler Aspen AT 2007-2010
- Chrysler PT Cruiser AT 2006-2010
- Chrysler Sebring AT 2007-2010
- Dodge Avenger AT 2008-2014
- Dodge Caliber (with start wire) AT 2007
- Dodge Caliber AT 2007-2012
- Dodge Charger AT 2006-2007
- Dodge Durango AT 2004
- Dodge Durango AT 2005-2006
- Dodge Durango AT 2007-2010
- Dodge Magnum AT 2005-2007
- Dodge Nitro AT 2007-2011
- Dodge Ram 1500 SRT AT 2006
- Dodge Ram 1500 AT 2006
- Dodge Ram 1500 AT 2007-2008
- Dodge Ram 2500 AT 2006
- Dodge Ram 2500 AT 2007-2009
- Dodge Ram 3500 chassis cab AT 2007-2009
- Dodge Ram 3500 AT 2005-2006
- Dodge Ram 3500 AT 2007-2009
- Dodge Ram 4500 chassis cab AT 2008-2010
- Dodge Ram 5500 chassis cab AT 2008-2010
- Jeep Commander AT 2006-2007
- Jeep Compass AT 2007-2017
- Jeep Grand Cherokee AT 2005-2007
- Jeep Liberty AT 2008-2012
- Jeep Patriot AT 2007-2017
- Jeep Wrangler JK AT 2007-2018
- Ram 4500 chassis cab AT 2010
- Ram 5500 chassis cab AT 2010
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the v
ehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 9 OF 9
Patent No. US 8,856,780 CA 2759622 2007-2008 Dodge Ram 1500 A
T
www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADSRSACH5HCX000AEN
20181115
+
i