Owner's Manual

ManualsBrandsiDatalink ManualsGPS & car accessoriesIDatastart

Table Of Contents

Chrysler 200 AT 2011-2014
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Chrysler 300 AT 2005-2007
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Chrysler Aspen AT 2007-2010
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Chrysler PT Cruiser AT 2006-2010
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Chrysler Sebring AT 2007-2010
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Avenger AT 2008-2014
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Caliber (with start wire) AT 2007
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Caliber AT 2007-2012
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Charger AT 2006-2007
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Durango AT 2004
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Durango AT 2005-2006
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Durango AT 2007-2010
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Magnum AT 2005-2007
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Nitro AT 2007-2011
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 1500 SRT AT 2006
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 1500 AT 2006
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 1500 AT 2007-2008
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 2500 AT 2006
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 2500 AT 2007-2009
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 3500 chassis cab AT 2007-2009
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 3500 AT 2005-2006
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 3500 AT 2007-2009
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 4500 chassis cab AT 2008-2010
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Dodge Ram 5500 chassis cab AT 2008-2010
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Jeep Commander AT 2006-2007
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Jeep Compass AT 2007-2017
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Jeep Grand Cherokee AT 2005-2007
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Jeep Liberty AT 2008-2012
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Jeep Patriot AT 2007-2017
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Jeep Wrangler JK AT 2007-2018
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Ram 4500 chassis cab AT 2010
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist
Ram 5500 chassis cab AT 2010
- T-Harness / Component Locator
- T-Harness / Wiring Diagram
- Hardwire / Component Locator
- Hardwire / Wiring Diagram
- Module Programming Procedure
- Takeover Procedure
- Installation Checklist

Patent No. US 8,856,780 CA 2759622

20181115

REVISION DATE

ADS-RSA-CH5-[HCX000A]

FIRMWARE

HCX000A

HARDWARE

ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.

VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.

ACCESSORIES

DOCUMENT NUMBER

2011-2014 CHRYSLER 200 AT

INSTALL GUIDE

Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certiﬁed Technicians who are

employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior

to beginning installation of an ADS product in a vehicle, it is the Certiﬁed Technician’s responsibility to review the most

current Product Guide, Install Guide and vehicle-speciﬁc notes available in Weblink®. ADS is not responsible for any

damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss

of time, loss of earnings, loss of proﬁt, commercial loss, loss of economic opportunity and the like that may or may not

have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to

suspend any Weblink® account without notice and decline to offer technical support to non-Certiﬁed Technicians, non-

compliant Certiﬁed Technicians or end users.

Summary of content (276 pages)

PAGE 1
INSTALL GUIDE 2011-2014 CHRYSLER 200 AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 2
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T014_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2011-2014 Chrysler 200 AT www.idatalink.
PAGE 3
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 4
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T014_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2011-2014 Chrysler 200 AT www.idatalink.
PAGE 5
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 r 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 IGNITION (+) PINK - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK - 04 12V (+) RED OR RED/TAN - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CANH (DATA) WHITE/ORANGE - 06 - M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•
PAGE 6
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 7
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 8
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 9
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 10
INSTALL GUIDE 2005-2007 CHRYSLER 300 AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 11
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A B c) I ,------;===========f ---;==~! \ C ~) ~ ~ T003_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2005-2007 Chrysler 300 AT www.idatalink.
PAGE 12
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! M2 M3 M5 M4 ! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY 2 WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS AFTER: IGNITION SWITCH (A) 1 VS2 1: SKIM CONNECTOR 2013/11/05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 2 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLA
PAGE 13
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A B c) I ,------;===========f ---;==~! \ C ~) ~ ~ T003_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2005-2007 Chrysler 300 AT www.idatalink.
PAGE 14
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/TAN - 04 CANH (DATA) WHITE/ORANGE - 06 I 8 7 6 5 4 3 2 1 CANL (DATA) WHITE - 07 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1 2 2 CONTROL (MUX) PURPLE/BROWN - 02 IGNITION (+) PINK/WHITE - 03 II M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 0
PAGE 15
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 16
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 17
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 18
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 19
INSTALL GUIDE 2007-2010 CHRYSLER ASPEN AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 20
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T010_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2010 Chrysler Aspen AT www.idatalink.
PAGE 21
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 22
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T010_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2010 Chrysler Aspen AT www.idatalink.
PAGE 23
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/GRAY - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/GRAY - 04 12V (+) RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/
PAGE 24
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 25
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 26
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 27
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 28
INSTALL GUIDE 2006-2010 CHRYSLER PT CRUISER AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 29
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A I ,------;===========f ---;==~! \ C B c) ~) ~ ~ T001_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2006-2010 Chrysler PT Cruiser AT www.idatalink.
PAGE 30
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! M2 M3 M5 M4 ! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY 2 WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS AFTER: IGNITION SWITCH (A) 1 VS2 1: SKIM CONNECTOR 2013/11/05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK
PAGE 31
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A I ,------;===========f ---;==~! \ C B c) ~) ~ ~ T001_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2006-2010 Chrysler PT Cruiser AT www.idatalink.
PAGE 32
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK - 04 CANH (DATA) WHITE/ORANGE - 06 I 8 7 6 5 4 3 2 1 CANL (DATA) WHITE - 07 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 2 2 CONTROL (MUX) PURPLE/BROWN - 02 1 IGNITION (+) PINK/WHITE - 03 II M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 B
PAGE 33
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 34
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 35
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 36
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 37
INSTALL GUIDE 2007-2010 CHRYSLER SEBRING AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 38
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T014_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2010 Chrysler Sebring AT www.idatalink.
PAGE 39
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 40
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T014_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2010 Chrysler Sebring AT www.idatalink.
PAGE 41
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 r 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 IGNITION (+) PINK - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK - 04 12V (+) RED OR RED/TAN - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CANH (DATA) WHITE/ORANGE - 06 - M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•
PAGE 42
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 43
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 44
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 45
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 46
INSTALL GUIDE 2008-2014 DODGE AVENGER AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 47
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T014_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2008-2014 Dodge Avenger AT www.idatalink.
PAGE 48
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 49
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T014_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2008-2014 Dodge Avenger AT www.idatalink.
PAGE 50
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 r 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 IGNITION (+) PINK - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK - 04 12V (+) RED OR RED/TAN - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CANH (DATA) WHITE/ORANGE - 06 - M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•
PAGE 51
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 52
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 53
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 54
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 55
INSTALL GUIDE 2007 DODGE CALIBER (WITH START WIRE) AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 56
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A I ,------;===========f ---;==~! \ C B c) ~) ~ ~ T002_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007 Dodge Caliber (with start wire) AT www.idatalink.
PAGE 57
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! M2 M3 M5 M4 ! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY 2 WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS AFTER: IGNITION SWITCH (A) 1 VS2 1: SKIM CONNECTOR 2013/11/05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 2 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLA
PAGE 58
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A I ,------;===========f ---;==~! \ C B c) ~) ~ ~ T002_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007 Dodge Caliber (with start wire) AT www.idatalink.
PAGE 59
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/YELLOW - 04 CANH (DATA) WHITE/ORANGE - 06 I 8 7 6 5 4 3 2 1 CANL (DATA) WHITE/PINK - 07 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 2 2 CONTROL (MUX) PURPLE/BROWN - 02 1 IGNITION (+) PINK/WHITE - 03 II M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BL
PAGE 60
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 61
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 62
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 63
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 64
INSTALL GUIDE 2007-2012 DODGE CALIBER AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 65
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T006_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2012 Dodge Caliber AT www.idatalink.
PAGE 66
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 67
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T006_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2012 Dodge Caliber AT www.idatalink.
PAGE 68
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r -J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/YELLOW - 04 12V (+) RED/LTGREEN - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CANH (DATA) WHITE/ORANGE - 06 - M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLAC
PAGE 69
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 70
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 71
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 72
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 73
INSTALL GUIDE 2006-2007 DODGE CHARGER AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 74
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A B c) I ,------;===========f ---;==~! \ C ~) ~ ~ T003_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2006-2007 Dodge Charger AT www.idatalink.
PAGE 75
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! M2 M3 M5 M4 ! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY 2 WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS AFTER: IGNITION SWITCH (A) 1 VS2 1: SKIM CONNECTOR 2013/11/05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 2 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLA
PAGE 76
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A B c) I ,------;===========f ---;==~! \ C ~) ~ ~ T003_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2006-2007 Dodge Charger AT www.idatalink.
PAGE 77
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/TAN - 04 CANH (DATA) WHITE/ORANGE - 06 I 8 7 6 5 4 3 2 1 CANL (DATA) WHITE - 07 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1 2 2 CONTROL (MUX) PURPLE/BROWN - 02 IGNITION (+) PINK/WHITE - 03 II M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 0
PAGE 78
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 79
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 80
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 81
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 82
INSTALL GUIDE 2004 DODGE DURANGO AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 83
PAGE 2 OF 7 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A B C c) I ,------;===========f ---;==~! \ ~) ~ ~ T017_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2004 Dodge Durango AT www.idatalink.
PAGE 84
PAGE 3 OF 7 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 1 CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M1 01 ORANGE - ACCESSORY (+) 02 RED - 12 VOLT (+) 03 PURPLE - STARTER (+) 04 PINK/WHITE - IGNITION 2 (+) 05 PINK - IGNITION (+) 06 WHITE - PARKING LIGHT (+) 07 RED - 12V (+) 08 BLACK - GROUND 8 7 6 5 4 3 2 1 I I I IGNITION HARNESS (B) M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/W
PAGE 85
PAGE 4 OF 7 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 86
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 5 OF 7 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 87
INSTALLATION CHECKLIST - 1 OF 2 PAGE 6 OF 7 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 88
PAGE 7 OF 7 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 89
INSTALL GUIDE 2005-2006 DODGE DURANGO AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 90
HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( PAGE 2 OF 7 20181115 ) \DOD/ A B C T018_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2005-2006 Dodge Durango AT www.idatalink.
PAGE 91
PAGE 3 OF 7 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 1 CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M1 01 ORANGE - ACCESSORY (+) 02 RED - 12 VOLT (+) 03 PURPLE - STARTER (+) 04 PINK/WHITE - IGNITION 2 (+) 05 PINK - IGNITION (+) 06 WHITE - PARKING LIGHT (+) 07 RED - 12V (+) 08 BLACK - GROUND 8 7 6 5 4 3 2 1 I I I IGNITION HARNESS (B) M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/W
PAGE 92
PAGE 4 OF 7 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 93
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 5 OF 7 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 94
INSTALLATION CHECKLIST - 1 OF 2 PAGE 6 OF 7 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 95
PAGE 7 OF 7 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 96
INSTALL GUIDE 2007-2010 DODGE DURANGO AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 97
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T012_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2010 Dodge Durango AT www.idatalink.
PAGE 98
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 99
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T012_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2010 Dodge Durango AT www.idatalink.
PAGE 100
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/GRAY - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/GRAY - 04 12V (+) RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/
PAGE 101
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 102
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 103
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 104
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 105
INSTALL GUIDE 2005-2007 DODGE MAGNUM AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 106
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A B c) I ,------;===========f ---;==~! \ C ~) ~ ~ T003_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2005-2007 Dodge Magnum AT www.idatalink.
PAGE 107
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! M2 M3 M5 M4 ! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY 2 WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS AFTER: IGNITION SWITCH (A) 1 VS2 1: SKIM CONNECTOR 2013/11/05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 2 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLA
PAGE 108
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A B c) I ,------;===========f ---;==~! \ C ~) ~ ~ T003_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2005-2007 Dodge Magnum AT www.idatalink.
PAGE 109
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/TAN - 04 CANH (DATA) WHITE/ORANGE - 06 I 8 7 6 5 4 3 2 1 CANL (DATA) WHITE - 07 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1 2 2 CONTROL (MUX) PURPLE/BROWN - 02 IGNITION (+) PINK/WHITE - 03 II M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 0
PAGE 110
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 111
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 112
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 113
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 114
INSTALL GUIDE 2007-2011 DODGE NITRO AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 115
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T007_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2011 Dodge Nitro AT www.idatalink.
PAGE 116
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 117
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T007_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2011 Dodge Nitro AT www.idatalink.
PAGE 118
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r -J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK - 04 12V (+) RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CANH (DATA) WHITE/LTGREEN - 06 - M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/
PAGE 119
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 120
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 121
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 122
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 123
INSTALL GUIDE 2006 DODGE RAM 1500 SRT AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 124
PAGE 2 OF 7 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T005_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2006 Dodge Ram 1500 SRT AT www.idatalink.
PAGE 125
PAGE 3 OF 7 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/GRAY - 04 CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M3 01 BROWN•SILVER DOT 02 BLACK/WHITE•SILVER DOT 03 PURPLE•SILVER DOT 04 GREEN•SILVER DOT 05 PURPLE/WHITE•SILVER DOT 06 WHITE/BLUE•SILVER DOT 07 GRAY•SILVER DOT - HOOD (-) INPUT 08 BLUE•SILVER DOT 09 GRAY/BLACK•SILVER DOT 10 EMPTY 1 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE
PAGE 126
PAGE 4 OF 7 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 127
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 5 OF 7 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 128
INSTALLATION CHECKLIST - 1 OF 2 PAGE 6 OF 7 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 129
PAGE 7 OF 7 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 130
INSTALL GUIDE 2006 DODGE RAM 1500 AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 131
PAGE 2 OF 7 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T005_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2006 Dodge Ram 1500 AT www.idatalink.
PAGE 132
PAGE 3 OF 7 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/GRAY - 04 CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M3 01 BROWN•SILVER DOT 02 BLACK/WHITE•SILVER DOT 03 PURPLE•SILVER DOT 04 GREEN•SILVER DOT 05 PURPLE/WHITE•SILVER DOT 06 WHITE/BLUE•SILVER DOT 07 GRAY•SILVER DOT - HOOD (-) INPUT 08 BLUE•SILVER DOT 09 GRAY/BLACK•SILVER DOT 10 EMPTY 1 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE
PAGE 133
PAGE 4 OF 7 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 134
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 5 OF 7 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 135
INSTALLATION CHECKLIST - 1 OF 2 PAGE 6 OF 7 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 136
PAGE 7 OF 7 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 137
INSTALL GUIDE 2007-2008 DODGE RAM 1500 AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 138
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2008 Dodge Ram 1500 AT www.idatalink.
PAGE 139
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 140
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2008 Dodge Ram 1500 AT www.idatalink.
PAGE 141
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/LTGREEN - 04 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT
PAGE 142
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 143
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 144
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 145
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 146
INSTALL GUIDE 2006 DODGE RAM 2500 AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 147
PAGE 2 OF 7 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T005_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2006 Dodge Ram 2500 AT www.idatalink.
PAGE 148
PAGE 3 OF 7 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/GRAY - 04 CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M3 01 BROWN•SILVER DOT 02 BLACK/WHITE•SILVER DOT 03 PURPLE•SILVER DOT 04 GREEN•SILVER DOT 05 PURPLE/WHITE•SILVER DOT 06 WHITE/BLUE•SILVER DOT 07 GRAY•SILVER DOT - HOOD (-) INPUT 08 BLUE•SILVER DOT 09 GRAY/BLACK•SILVER DOT 10 EMPTY 1 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE
PAGE 149
PAGE 4 OF 7 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 150
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 5 OF 7 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 151
INSTALLATION CHECKLIST - 1 OF 2 PAGE 6 OF 7 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 152
PAGE 7 OF 7 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 153
INSTALL GUIDE 2007-2009 DODGE RAM 2500 AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 154
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2009 Dodge Ram 2500 AT www.idatalink.
PAGE 155
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 156
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2009 Dodge Ram 2500 AT www.idatalink.
PAGE 157
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/LTGREEN - 04 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT
PAGE 158
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 159
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 160
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 161
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 162
INSTALL GUIDE 2007-2009 DODGE RAM 3500 CHASSIS CAB AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 163
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2009 Dodge Ram 3500 chassis cab AT www.idatalink.
PAGE 164
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 165
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2009 Dodge Ram 3500 chassis cab AT www.idatalink.
PAGE 166
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/LTGREEN - 04 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT
PAGE 167
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 168
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 169
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 170
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 171
INSTALL GUIDE 2005-2006 DODGE RAM 3500 AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 172
PAGE 2 OF 7 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T005_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2005-2006 Dodge Ram 3500 AT www.idatalink.
PAGE 173
PAGE 3 OF 7 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/GRAY - 04 CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M3 01 BROWN•SILVER DOT 02 BLACK/WHITE•SILVER DOT 03 PURPLE•SILVER DOT 04 GREEN•SILVER DOT 05 PURPLE/WHITE•SILVER DOT 06 WHITE/BLUE•SILVER DOT 07 GRAY•SILVER DOT - HOOD (-) INPUT 08 BLUE•SILVER DOT 09 GRAY/BLACK•SILVER DOT 10 EMPTY 1 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE
PAGE 174
PAGE 4 OF 7 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 175
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 5 OF 7 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 176
INSTALLATION CHECKLIST - 1 OF 2 PAGE 6 OF 7 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 177
PAGE 7 OF 7 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 178
INSTALL GUIDE 2007-2009 DODGE RAM 3500 AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 179
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2009 Dodge Ram 3500 AT www.idatalink.
PAGE 180
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 181
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2009 Dodge Ram 3500 AT www.idatalink.
PAGE 182
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/LTGREEN - 04 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT
PAGE 183
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 184
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 185
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 186
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 187
INSTALL GUIDE 2008-2010 DODGE RAM 4500 CHASSIS CAB AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 188
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2008-2010 Dodge Ram 4500 chassis cab AT www.idatalink.
PAGE 189
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 190
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2008-2010 Dodge Ram 4500 chassis cab AT www.idatalink.
PAGE 191
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/LTGREEN - 04 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT
PAGE 192
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 193
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 194
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 195
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 196
INSTALL GUIDE 2008-2010 DODGE RAM 5500 CHASSIS CAB AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 197
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2008-2010 Dodge Ram 5500 chassis cab AT www.idatalink.
PAGE 198
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 199
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2008-2010 Dodge Ram 5500 chassis cab AT www.idatalink.
PAGE 200
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/LTGREEN - 04 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT
PAGE 201
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 202
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 203
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 204
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 205
INSTALL GUIDE 2006-2007 JEEP COMMANDER AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 206
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ C ~) ~ ~ B T004_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2006-2007 Jeep Commander AT www.idatalink.
PAGE 207
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! M2 M3 M5 M4 ! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY 2 WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS AFTER: IGNITION SWITCH (A) 1 VS2 1: SKIM CONNECTOR 2013/11/05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 2 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BL
PAGE 208
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ C ~) ~ ~ B T004_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2006-2007 Jeep Commander AT www.idatalink.
PAGE 209
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/LTBLUE - 04 CANH (DATA) WHITE/ORANGE - 06 I CANL (DATA) WHITE - 07 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CONTROL (MUX) PURPLE/BROWN - 02 8 7 6 5 4 3 2 1 1 2 2 IGNITION (+) PINK/LTGREEN - 03 II 5 4 3 2 1 STARTER (+) PINK/ORANGE - 04 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT
PAGE 210
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 211
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 212
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 213
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 214
INSTALL GUIDE 2007-2017 JEEP COMPASS AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 215
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T006_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2017 Jeep Compass AT www.idatalink.
PAGE 216
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 217
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T006_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2017 Jeep Compass AT www.idatalink.
PAGE 218
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r -J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/YELLOW - 04 12V (+) RED/LTGREEN - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CANH (DATA) WHITE/ORANGE - 06 - M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLAC
PAGE 219
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 220
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 221
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 222
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 223
INSTALL GUIDE 2005-2007 JEEP GRAND CHEROKEE AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 224
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ C ~) ~ ~ B T004_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2005-2007 Jeep Grand Cherokee AT www.idatalink.
PAGE 225
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! M2 M3 M5 M4 ! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY 2 WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS AFTER: IGNITION SWITCH (A) 1 VS2 1: SKIM CONNECTOR 2013/11/05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 2 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BL
PAGE 226
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ C ~) ~ ~ B T004_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2005-2007 Jeep Grand Cherokee AT www.idatalink.
PAGE 227
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 GROUND (-) BLACK/LTBLUE - 04 CANH (DATA) WHITE/ORANGE - 06 I CANL (DATA) WHITE - 07 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CONTROL (MUX) PURPLE/BROWN - 02 8 7 6 5 4 3 2 1 1 2 2 IGNITION (+) PINK/LTGREEN - 03 II 5 4 3 2 1 STARTER (+) PINK/ORANGE - 04 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT
PAGE 228
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 229
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 230
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 231
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 232
INSTALL GUIDE 2008-2012 JEEP LIBERTY AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 233
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T008_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2008-2012 Jeep Liberty AT www.idatalink.
PAGE 234
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 235
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T008_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2008-2012 Jeep Liberty AT www.idatalink.
PAGE 236
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 IGNITION (+) PINK/WHITE - 03 r-J:-· :1 GROUND (-) BLACK/YELLOW - 04 8 7 6 5 4 3 2 1 12V (+) RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CANH (DATA) WHITE/BLACK - 06 CANL (DATA) WHITE/LTBLUE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05
PAGE 237
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 238
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 239
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 240
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 241
INSTALL GUIDE 2007-2017 JEEP PATRIOT AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 242
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T006_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2017 Jeep Patriot AT www.idatalink.
PAGE 243
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 244
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ B ~) ~ ~ T006_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2017 Jeep Patriot AT www.idatalink.
PAGE 245
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r -J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/YELLOW - 04 12V (+) RED/LTGREEN - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CANH (DATA) WHITE/ORANGE - 06 - M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLAC
PAGE 246
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 247
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 248
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 249
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 250
INSTALL GUIDE 2007-2018 JEEP WRANGLER JK AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 251
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ ~) ~ ~B T009_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2018 Jeep Wrangler JK AT www.idatalink.
PAGE 252
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 253
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ A c) I ,------;===========f ---;==~! \ ~) ~ ~B T009_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2007-2018 Jeep Wrangler JK AT www.idatalink.
PAGE 254
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK - 04 12V (+) RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK CANH (DATA) WHITE/BLACK - 06 - M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHI
PAGE 255
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 256
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 257
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 258
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 259
INSTALL GUIDE 2010 RAM 4500 CHASSIS CAB AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 260
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2010 Ram 4500 chassis cab AT www.idatalink.
PAGE 261
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 262
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2010 Ram 4500 chassis cab AT www.idatalink.
PAGE 263
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/LTGREEN - 04 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT
PAGE 264
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 265
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 266
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 267
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.
PAGE 268
INSTALL GUIDE 2010 RAM 5500 CHASSIS CAB AT DOCUMENT NUMBER REVISION DATE 20181115 FIRMWARE ADS-RSA-CH5-[HCX000A] HARDWARE HCX000A ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE. TERMS OF USE Automotive Data Solutions Inc.
PAGE 269
PAGE 2 OF 9 20181115 T-HARNESS / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_H Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2010 Ram 5500 chassis cab AT www.idatalink.
PAGE 270
PAGE 3 OF 9 20181115 T-HARNESS / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 VS2 1: SKIM CONNECTOR M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK 1: SKIM HARNESS VS1 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT 05 GREEN/BLACK•BLACK DOT 06 BLUE/WHITE•BLACK DOT 07 EMPTY 1 08 WHITE/PURPLE•BLACK DOT 09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK•BLAC
PAGE 271
PAGE 4 OF 9 20181115 HARDWIRE / COMPONENT LOCATOR - 1 OF 1 ( ) \DOD/ B A c) I ,------;===========f ---;==~! \ C ~) ~ ~ T013_W Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2018 ADS-RSA-CH5-[HCX000A]-EN 2010 Ram 5500 chassis cab AT www.idatalink.
PAGE 272
PAGE 5 OF 9 20181115 HARDWIRE / WIRING DIAGRAM - 1 OF 1 M1 ! ! M2 M3 CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M5 M4 1 KEYSWITCH (MUX) PURPLE/BROWN - 01 r-J:-· :1 IGNITION (+) PINK/WHITE - 03 8 7 6 5 4 3 2 1 GROUND (-) BLACK/LTGREEN - 04 12V (+) GRAY/RED - 05 M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK I CANH (DATA) WHITE/ORANGE - 06 CANL (DATA) WHITE - 07 M2 01 GREEN•BLACK DOT 02 BLUE•BLACK DOT 03 RED/WHITE•BLACK DOT 04 GREEN/WHITE•BLACK DOT
PAGE 273
PAGE 6 OF 9 20181115 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 13 Wait, LED 2 will flash GREEN. 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. 14 Module Programming Procedure completed. Set ignition to ON position. 09 03 OFF ACC r ON START 0 10 ENGINE START STOP 04 05 ~ \.
PAGE 274
TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC >> 0 PAGE 7 OF 9 20181115 Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc.
PAGE 275
INSTALLATION CHECKLIST - 1 OF 2 PAGE 8 OF 9 20181115 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock?  YES: Go to next step.  NO: Repeat step.
PAGE 276
PAGE 9 OF 9 20181115 INSTALLATION CHECKLIST - 2 OF 2 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start?  YES: Go to next step.  NO: The module doesn't detect OEM remote lock button from the vehicle communication network.