QUICK START GUIDE THESE PRODUCTS REQUIRE ONLINE PROGRAMMING BEFORE INSTALLATION. DETAILS INSIDE.
6 STEPS TO GET STARTED INSTALL THE WEBLINK PLUG-IN 1 Go to: idatalinkmaestro.com/plugin and follow the installation steps. LOG INTO WEBLINK Go to: idatalinkmaestro.com/login. Enter your username and password, then click OK. 4 Review the System Requirements before installing. REGISTER A WEBLINK ACCOUNT 2 Go to: idatalinkmaestro.com/register and complete the registration process. A confirmation email will be sent to you requiring validation.
install guide ADS-SW(SI)-ALL01-AS-IG-EN fiRmware ADS-SW(SI)-ALL01-AS-EN hardware ADS-MSW Document number 9729 Revision Date 20120913 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician.
suggEsTED TOOls - 1 Of 1 ADS-SW(SI)-ALL01-AS-IG-EN 01 Page 2 of 8 DOC.
INSTALLATION OVERVIEW - 1 OF 1 ADS-SW(SI)-ALL01-AS-IG-EN Page 3 of 8 DOC.
mODulE INsTallaTION PROCEDuRE - 1 Of 1 ADS-SW(SI)-ALL01-AS-IG-EN 01 Refer to WIRE CHART and locate wires. >> 02 03 04 05 WARNING: Do not connect module PURPLE/ YELLOW wire (Connector A, Pin 2) nor PINK/ YELLOW wire (Connector A, Pin 4). 1 2 3 4 5 6 7 1 2 3 4 5 6 7 07 1 2 3 4 5 6 7 1 2 3 4 5 6 7 If SWI-2 wire exists, connect module PINK/ RED wire (Connector A, Pin 3) to SWI-2 wire. SWI-2 If another SWI-F wire exists, connect module BLACK/WHITE wire (Connector A, Pin 5) to SWI-F wire.
Page 5 of 8 DOC.
Page 6 of 8 DOC.: #9729 • 20120913 fuNCTION PaIRINg PROCEDuRE - 1 Of 2 ADS-SW(SI)-ALL01-AS-IG-EN >> 01 ACC NOTE: [X], [Y] & [Z] are numerical variables identified in the FUNCTION PAIRING CHART. 05 Turn key to ON position. 06 ON START OFF [X] [X] Press programming button [X] times. 09 LED will flash [X] times. 10 Refer to FUNCTION PAIRING CHART. [Y] Find the number associated to the radio brand: [Y]. 02 LED will turn solid GREEN.
Page 7 of 8 DOC.: #9729 • 20120913 fuNCTION PaIRINg PROCEDuRE - 2 Of 2 ADS-SW(SI)-ALL01-AS-IG-EN 15 >> [Z] LED will flash GREEN [Z] times to match the function [Z]. EXAMPLE: If LED flashes 3 times, the corresponding function is 3. 18 >> Repeat steps 16 and 17 for every other steering wheel button and its corresponding function. 22 NOTE: LED will flash RED once [1x] for function 10. 23 Insert key into ignition. ACC ON START OFF Turn key to ON position. LED will remain OFF.
mODulE REsET PROCEDuRE - 1 Of 1 ADS-SW(SI)-ALL01-AS-IG-EN 1 Turn key to OFF position. ACC ON Module reset procedure completed. START OFF 2 ACC OFF ON START Press and hold programming button and turn key to ON position. 3 Wait, LED will flash RED rapidly. (This may take up to 10 seconds.) 4 Release programming button. 5 Wait, LED will turn solid GREEN for 2 seconds. 6 7 Page 8 of 8 DOC.: #9729 • 20120913 Turn key to OFF position. ACC OFF ON START Automotive Data Solutions Inc.
1 YEAR LIMITED WARRANTY Automotive Data Solutions Inc. (“ADS”) warrants to the original purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances, for the period of one (1) year as of the original date of purchase. In the event of any product malfunction during the Warranty period, the original purchaser must return to the Authorized Dealer where it was originally purchased with the original proof of purchase.
