Owner's Manual

ManualsBrandsiDatalink ManualsAudio accessories & installationConnec Factory Integration Adapter

INSTALL TYPE 1 - WITH A FACTORY AMPLIFIER

Every step description is illustrated on the next page.

STEP 1:

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket

radio main harness to the GM5 T-harness and match the

wire functions.

STEP 2:

• Remove the factory radio.

• Connect the factory harness to the GM5 T-harness.

• Connect only the available connectors. For example, if the

factory harness has two connectors, connect only these two

connectors.

STEP 3:

• Access the OBDII connector located under the driver side

dashboard.

• Connect the BROWN/RED wire of the GM5 T-harness to the

TAN/BLACK wire of the OBDII connector located at pin 6.

• Connect the BROWN/YELLOW wire of the GM5 T-harness

to the TAN wire of the OBDII connector located at pin 14.

STEP 4:

• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Insert the LEFT FRONT white RCA connector from the

GM5 T-harness into the LEFT FRONT RCA output of the

aftermarket radio.

• Plug the Data cable to the data port of the aftermarket

radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack

of the aftermarket radio.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connector labeled SUB IN can be used to feed the

subwoofer channel of the factory ampliﬁ er.

The RCA connector labeled CENTER IN can be used to feed

the center channel of the factory ampliﬁ er.

The RCA connectors labeled BACKUP CAM can be used to

retain the functionality of the factory backup camera.

STEP 5:

• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

MODULE SETUP:

• Insert the key into the ignition and turn it to the ACC

position.

• The Radio will turn on and the setup screen will appear.

Choose one of the two Bluetooth OPTIONS below:

OPTION 1:

This option lets the factory Bluetooth system handle calls and

the aftermarket Bluetooth system stream Audio.

To use the factory Bluetooth system:

(The factory Bluetooth system is OFF by default)

• Scroll down to GM setup and press SET

• Go to the OEM Bluetooth and press ON

• Press the BACK button (circular shaped arrow)

• Scroll down then press FINISH

OPTION 2:

This option lets the aftermarket Bluetooth system handle

calls and stream Audio.

To use the aftermarket Bluetooth system:

• Scroll to the bottom of the setup screen and press FINISH

• Install the aftermarket microphone

WARNING: Aftermarket Bluetooth system

If your phone is paired to the Factory Bluetooth system

you must delete the pairing from the phone to the Factory

Bluetooth system.

For more information and programming procedures, see

the aftermarket Bluetooth system and the factory Bluetooth

system owner’s manuals.

The module is now programmed and ready to be used.

To access the new menus, press on GM FEATURES.

Insert the aftermarket radio in the dashboard housing and test

all the functionalities. Reassemble the dashboard carefully.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the

key to the OFF position then disconnect all connectors

from the module. Press and hold the module’s

programming button and connect all the connectors

back to the module. Wait, the module’s LED will ﬂ ash

RED rapidly (this may take up to 10 seconds). Release

the programming button. Wait, the LED will turn solid

GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or

e-mail "support@idatalink.com". Visit us at "maestro.

idatalink.com/support" and "www.12voltdata.com/

forum/"

PAGE 4 OF 9

• 20130729