• 20130729 INSTALL GUIDE WITH GM5 T-HARNESS RETAINS STEERING WHEEL CONTROLS, ONSTARTM, ONSTARTM BLUETOOTH, XMTM SATELLITE AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro GM5 Installation Harness OPTIONAL ACCESSORIES None PROGRAMMED FIRMWARE ADS-RR(SR)-GMS05-DS-EN NOTICE: Automotive Data Solutions Inc.
PAGE 2 OF 9 • 20130729 GETTING STARTED WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now s few simple steps away from enjoying your new car radio with enhanced features. To complete the installation of your product, please follow the step-by-step instructions outlined below. 1- INSTALL THE WEBLINK UPDATER PLUG-IN • Go to "http://maestro.idatalink.
PAGE 3 OF 9 • 20130729 WEBLINK REFERENCE 1- Visit maestro.idatalink.com and click on FLASH YOUR MODULE to access the WEBLINK menu. 1 2- Log in if you are already registered. 3- Create an account if you are not registered. 10 4- Select your vehicle’s make, year and model. 5- Select your vehicle’s factory radio trim. This is not to be confused with the aftermarket radio that you are about to install. 9 2 11 3 12 6- Select the steering wheel that matches the one in your vehicle.
INSTALL TYPE 1 - WITH A FACTORY AMPLIFIER Every step description is illustrated on the next page. STEP 1: • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the GM5 T-harness and match the wire functions. STEP 2: MODULE SETUP: • Insert the key into the ignition and turn it to the ACC position. • The Radio will turn on and the setup screen will appear.
PAGE 5 OF 9 • 20130729 INSTALL TYPE 1 - WIRING DIAGRAM STEP 4 DATA CABLE AUDIO CABLE STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
INSTALL TYPE 2 - WITHOUT A FACTORY AMPLIFIER Every step description is illustrated on the next page. STEP 1: • Unbox the aftermarket radio and locate its main harness. • Cut the level matching circuits from the GM5 T-harness, they are not required. STEP 2: • Connect the wires shown on the next page from aftermarket radio main harness to the GM5 T-harness and match the wire functions. STEP 3: • Remove the factory radio. • Connect the factory harness to the GM5 T-harness.
PAGE 7 OF 9 • 20130729 INSTALL TYPE 2 - WIRING DIAGRAM STEP 5 DATA CABLE AUDIO CABLE STEP 1 STEP 2 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
INSTALL TYPE 3 - WITH AN AFTERMARKET AMPLIFIER Every step description is illustrated on the next page. STEP 1: • Unbox the aftermarket radio and locate its main harness. • The speaker wire connections of the GM5 T-harness are not required. • Connect the wires shown on the next page from aftermarket radio main harness to the GM5 T-harness and match the wire functions. STEP 2: • A small 4 ohm speaker is required to retain the factory warning chimes and turn signal reminder.
PAGE 9 OF 9 • 20130729 INSTALL TYPE 3 - WIRING DIAGRAM STEP 5 DATA CABLE AUDIO CABLE STEP 1 STEP 2 AFTERMARKET SPEAKER (SOLD SEPARATELY) BLUE B WHITE (NOT CONNECTED) WHITE/BLACK (NOT CONNECTED) GRAY (NOT CONNECTED) GRAY/BLACK (NOT CONNECTED) GREEN (NOT CONNECTED) GREEN/BLACK (NOT CONNECTED) PURPLE (NOT CONNECTED) PURPLE/BLACK (NOT CONNECTED) BLUE/WHITE - AMP.
• 20130806 INSTALL GUIDE WITH GM5 T-HARNESS RETAINS STEERING WHEEL CONTROLS, 11854 ONSTARTM, FACTORY AMPLIFIER CONTROL, ANALOG OUTPUTS AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro GM5 Installation Harness OPTIONAL ACCESSORIES None PROGRAMMED FIRMWARE ADS-RR(SR)-GMS05-AS-EN NOTICE: Automotive Data Solutions Inc.
PAGE 2 OF 10 DOC.: #11854 • 20130806 GETTING STARTED WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now s few simple steps away from enjoying your new car radio with enhanced features. To complete the installation of your product, please follow the step-by-step instructions outlined below. INSTALL TYPE 1 Used for vehicles with a factory amplifier* • Follow the INSTALLATION INSTRUCTIONS listed on page 4.
PAGE 3 OF 10 DOC.: #11854 • 20130806 WEBLINK REFERENCE 1- Visit maestro.idatalink.com and click on FLASH YOUR MODULE to access the WEBLINK menu. 1 2- Log in if you are already registered. 3- Create an account if you are not registered. 10 4- Select your vehicle’s make, year and model. 5- Select your vehicle’s factory radio trim. This is not to be confused with the aftermarket radio that you are about to install. 9 2 6- Select the steering wheel that matches the one in your vehicle.
PAGE 4 OF 10 DOC.: #11854 • 20130806 INSTALL TYPE 1 - WITH A FACTORY AMPLIFIER Every step description is illustrated on the next page. STEP 1: • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the GM5 T-harness and match the wire functions. STEP 2: • Remove the factory radio. • Connect the factory harness to the GM5 T-harness. • Connect only the available connectors.
PAGE 5 OF 10 DOC.: #11854 • 20130806 INSTALL TYPE 1 - WIRING DIAGRAM STEP 3 RADIO CONTROL CABLE STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 6 OF 10 DOC.: #11854 • 20130806 INSTALL TYPE 2 - WITHOUT A FACTORY AMPLIFIER Every step description is illustrated on the next page. STEP 1: • Unbox the aftermarket radio and locate its main harness. • Cut the level matching circuits from the GM5 T-harness, they are not required. STEP 2: • Connect the wires shown on the next page from aftermarket radio main harness to the GM5 T-harness and match the wire functions. STEP 3: • Remove the factory radio.
PAGE 7 OF 10 DOC.: #11854 • 20130806 INSTALL TYPE 2 - WIRING DIAGRAM STEP 4 RADIO CONTROL CABLE STEP 1 STEP 2 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 8 OF 10 DOC.: #11854 • 20130806 INSTALL TYPE 3 - WITH AN AFTERMARKET AMPLIFIER Every step description is illustrated on the next page. STEP 1: • Unbox the aftermarket radio and locate its main harness. • The speaker wire connections of the GM5 T-harness are not required. • Connect the wires shown on the next page from aftermarket radio main harness to the GM5 T-harness and match the wire functions.
PAGE 9 OF 10 DOC.: #11854 • 20130806 INSTALL TYPE 3 - WIRING DIAGRAM STEP 4 RADIO CONTROL CABLE STEP 2 STEP 1 AFTERMARKET SPEAKER (SOLD SEPARATELY) WHITE (NOT CONNECTED) WHITE/BLACK (NOT CONNECTED) GRAY (NOT CONNECTED) GRAY/BLACK (NOT CONNECTED) GREEN (NOT CONNECTED) GREEN/BLACK (NOT CONNECTED) PURPLE (NOT CONNECTED) PURPLE/BLACK (NOT CONNECTED) BLUE/WHITE - AMP.
PAGE 10 OF 10 DOC.: #11854 • 20130806 RADIO CONTROL CABLE - WIRING DIAGRAM SELECT RADIO BRAND AND CONNECT RADIO CONTROL CABLE ACCORDINGLY. KENWOOD RADIO OR (NOT CONNECTED) BLAUPUNKT RADIO OR MAESTRO RR MODULE SW CONTROL - GRAY (NOT CONNECTED) SW CONTROL GROUND - BLACK E ECLIPSE RADIO OR (NOT CONNECTED) RED BLACK (NOT CONNECTED) WHITE BROWN/BLACK BROWN OTHER AFTERMARKET RADIOS OR Automotive Data Solutions Inc. © 2013 (NOT CONNECTED) ADS-RR(SR)-GMS05-ASTH-IG-EN maestro.idatalink.
