Quick Guide

Battery safety Use barcode scanning function Issue handling RADIO FREQUENCY MAXIMUM TRANSMIT
POWER AND FREQUENCY BAND INFORMATION
Use barcode scanning function
Press yellow scan key to scan; scanning
indicator turns from red to green with beep
sound means scanning successfully.
Use barcode scanning function
Product is using Polymer battery.
Please use original charger, do not change to
other charge stand or power adapter.
When you firstly use the battery, its volume
would be only 50%, you can charge it by original
power adapter or charge stand(Purchase), first
time charging should be above 8 hours.
Avoid metal material(such as keys) contact to the
battery electrode which might cause short circuit.
Do not put battery into overheated, too wet, or
corrosive environment.
Do not put fully-charged battery to long-term
storage, store in 50% battery volume.
If device not being used for a long time, take out
the battery.
If the battery has bulge or expansion, please
change to a new battery.
1. Menu->iScan, tag to open;
2. Tag right side of “Launch barcode scan”, shows
“√”, means function is on.(Tag again to turn off)
1. Issue: Can not power on.
Fix: Charging;
2. Issue: Not showing battery icon when charging.
Fix: Charge continuously for 1 hour, if still not
working, contact after-sale service.
3. Issue: Battery charging slowly.
Fix: Make sure using original battery.
4. Issue: No internet access after installing SIM card.
Fix: Check if SIM card is out of balance or installing
incorrectly.
After-sales Service
After-sales QQ account: 2782597064 (nickname: iData after-sales)
Email: [e-mail]
Official website: www.idataglobal.com
Address: Floor 11, Building B1, No.999 Gaolang East Road, Wuxi City, P.R.C.
To know more product information and download detailed instructions,
visit the official website of iData.
The supporting software and SDK for relevant functions help you better
use the iData K1
© 2019 IDATA GLOBAL. All Rights Reserved.
iData series product warranty card
De ar customer,
Thank you for choosing iData product. Y ou may e njoy the following
services after buying iD ata product:
【Warranty of free repair service】
1）12-month warranty is given to the device and battery and
3-month warranty is given to other accessories from the day
of purchase against functional failure that is not caused due to
manmade damage.
2）Our after-sale service department will mail out the repaired
device within 24 hours after the device with any problem is
received, so as to keep you wait for the shortest possible time.
3）A device of the same model will be provided free of charge for
replacement of the device that cannot be used normally after
being returned for repair due to the same problem for 3 times
in 1 year.
The parts needed for the product repair service will be available for
no more than 1 year after the product manufacturing ceases.
Note:
Reminder:
Please contact our customer service staff before sending any product to us
【Warranty of paid repair service】
You may choose to use our paid repair service under the following
circumstances (including but not limited to):
1）There is no warranty card, or the valid invoice is missing, or the
warranty period has expired;
2）The damage is caused due to force majeure incidents, such as
fire, flood, thunder and earthquake;
3）The damage is caused as a result of the user’s failure to
follow the user’s manual on the use, maintenance and
storage of the product.
4）The damage is caused due to the breakdown and repair of the
device by non-authorized service personnel.
5）Normal wear or consumption of the product is found in its use.
6）The product cannot be used due to the reason related to the
user’s own internet connection and software problem.
Certificate of Quality
QC Passed Approved for shipment
QA
Ver：V1.1
1. Use careful with the earphone maybe possible excessive
sound pressure from earphones and headphones can
cause hearing loss.
2. Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.
3. The product shall only be connected to a USB interface of version
USB2.0 or higher.
4. Adapter shall be installed near the equipment and shall be easily
accessible.
5. The operating temperature of the EUT can’t exceed 40℃ and
shouldn’t be lower than -20℃.
6. The plug considered as disconnect device of adapter.
7. The device complies with RF specifications when the device used at
5mm from your body
8. The band 5150-5350MHz indoor use only.
Hereby, Wuxi iData Technology Company Ltd. declares that this Mobile
phone product is in compli
ance with essential requirements and other
relevant provisions of Directive 2014/53/EU. This product is allowed to
be used in all EU member states.
Frepuency bands
GSM 900
DCS 1800
WCDMA Band I
WCDMA Band VIII
LTE Band 1
LTE Band 3
LTE Band 7
LTE Band 8
LTE Band 20
LTE Band 34
LTE Band 38
LTE Band 40
BT EDR(EIRP)
BT BLE(EIRP)
WIFI(EIRP)
RLAN Band 1(EIRP)
RLAN Band 2(EIRP)
RLAN Band 3(EIRP)
5.8G SRD
Maximum output power
32.91 dBm
29.96 dBm
24.89 dBm
23.57 dBm
23.28 dBm
22.37 dBm
22.84 dBm
24.07 dBm
22.57 dBm
23.93 dBm
24.05 dBm
24.30 dBm
6.94 dBm
-8.11 dBm
16.97 dBm
17.81 dBm
17.08 dBm
16.59 dBm
12.21 dBm
15.19 Labeling requirements.
T
his device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment. WiFi 5G does not support hotspot.
15.105 Information to user.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This product meets the government's requirements for exposure to
radio waves. The guidelines are based on standards that were
developed by independent scientific organizations through periodic
and thorough evaluation of scientific studies. The standards include a
substantial safety margin designed to assure the safety of all persons
regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA
(FCC) is 1.6 W/kg averaged over one gram of tissue. This device was
tested for typical body-worn operations with the back of the handset
kept 10mm from the body. To maintain compliance with FCC RF
exposure requirements, use accessories that maintain a 10mm
separation distance between the user's body and the back of the
device. The use of belt clips, holsters and similar accessories should
not contain metallic components in its assembly. The use of
accessories that do not satisfy these requirements may not comply
with FCC RF exposure requirements, and should be avoided.