Manual IB-180MC-C31 DockingStation for M.2 NVMe & SATA SSD Handbuch IB-180MC-C31 DockingStation für M.
Sicherheitshinweise Zur Vermeidung körperlicher Schäden, sowie von Sach-, Geräteschäden und Datenverlust beachten Sie bitte folgende Hinweise: Warnstufen Signalwort und Sicherheitszeichen kennzeichnen die Warnstufe und geben einen sofortigen Hinweis auf Wahrscheinlichkeit, Art und Schwere der Folgen, wenn die Maßnahmen zur Vermeidung der Gefahr nicht befolgt werden. GEFAHR warnt vor einer unmittelbar gefährlichen Situation, die zum Tod oder zu schweren Verletzungen führen wird.
Sicherheitshinweise • • • • • 4.
Safety Information Please read carefully the following information to prevent injuries, damage to material and device as well as data loss: Warning levels Signal words and safety codes indicate the warning level and provide immediate information in terms of the probability of occurrence as well as the type and severity of the consequences if the measures to prevent hazards are not complied with. DANGER Warns of a directly hazardous situation causing death or serious injury.
Safety Information • • • • 4.
Manual IB-180MC-C31 Package content 1x IB-180MC-C31 1x USB Type-C® to Type-C® cable with Type-A adapter 2x Rubber fixation 1x Heat sink 2x Thermal pad 2x Rubber ring 1x Manual System requirements One free USB 3.2 (Gen 2) Type-C® or Type-A connection on your host computer. Key features • Easy and fast docking of one M.2 NVMe or SATA SSD • Host connection via USB 3.2 (Gen 2) Type-C® or Type-A • Data transfer rates of up to 10 Gbit/s • For 22x 42/60/80 mm M.
Manual IB-180MC-C31 1 2 4 3 5 6 7 Overview 1. Rubber fixation 2. ON/OFF button 3. Power LED 4. USB Type-C® host connection 5. Heat sink 6. Thermal pad 7. M.
Manual IB-180MC-C31 Installation ATTENTION! When installing or uninstalling the M.2 SSD, make sure that the IB180MC-C31 is always switched off (press ON/OFF button, power LED lights up red) or disconnected from the host computer to avoid data loss. 1. Install the rubber fixation to your required position (42/60/80 mm): Put the rubber fixation through the large hole and push it into the smaller area of the hole 42 60 80 HINT: If you use an M.
Manual IB-180MC-C31 3. Pull the rubber fixation to the rear and push the M.2 SSD down in position. Release the rubber fixation. The SSD is now locked in place. 4. Connect the cable with the USB Type-C® plug to the IB-180MC-C31. 5. 6. Connect the cable with the Type-C® or Type-A plug to your host computer. Once the IB-180MC-C31 is connected to the host computer the power LED lights up red.
Manual IB-180MC-C31 7. Press the ON/OFF button to power the device. The power LED lights up white. 8. To deinstall the M.2 SSD please press the ON/OFF button again to power off the IB-180MC-C31 (power LED red). Please await the end of read/write operations before switching off the device to avoid data loss. Usage • Power LED red – Power OFF • Power LED white – Power ON • Please await the end of read/write operations before disconnecting the device to avoid data loss.
Handbuch IB-180MC-C31 Verpackungsinhalt 1x IB-180MC-C31 1x USB Type-C® zu Type-C® Kabel mit Type-A Adapter 2x M.2 Gummifixierung 1x Kühlkörper 2x Wärmeleitpad 2x Gummiband 1x Handbuch Systemanforderungen Ein freier USB 3.2 (Gen 2) Type-C® oder Type-A Anschluss an Ihrem Hostcomputer. Hauptmerkmale • Einfaches und schnelles Andocken einer M.2 NVMe oder SATA SSD • Hostanschluss über USB 3.2 (Gen 2) Type-C® oder Type-A • Datenübertragungsraten von bis zu 10 Gbit/s • Für 22x 42/60/80 mm M.
Handbuch IB-180MC-C31 1 2 4 3 5 6 7 Überblick 1. Gummifixierung 2. Power Taste 3. Power LED 4. Type-C® Hostverbindung 5. Kühlkörper 6. Wärmeleitpads 7. M.
Handbuch IB-180MC-C31 Installation ACHTUNG! Bei der Installation oder Deinstallation der M.2 SSD ist darauf zu achten, dass das IB-180MC-C31 in jedem Fall ausgeschaltet (Power Taste drücken, Power LED leuchtet rot) oder vom Hostcomputer getrennt ist, um Datenverlust zu vermeiden. 1. Bringen Sie die Gummifixierung an der gewünschten Position an (42/60/80 mm): Stecken Sie die Gummifixierung durch das große Loch und schieben Sie sie in den kleineren Bereich des Lochs. 42 60 80 HINWEIS: Wenn Sie eine M.
Handbuch IB-180MC-C31 3. Ziehen Sie die Gummifixierung nach hinten und drücken Sie die M.2 SSD nach unten in Position. Lassen Sie die Gummifixierung los. Die SSD ist nun eingerastet. 4. Schließen Sie das Kabel mit dem USB Type-C®-Stecker an das IB-180MC-C31 an. 5. Schließen Sie das Kabel mit dem Type-C® oder Type-A-Stecker an Ihren Hostcomputer an. Wenn das IB-180MC-C31 an den Hostcomputer angeschlossen ist, leuchtet die Power LED rot. 6.
Handbuch IB-180MC-C31 7. Drücken Sie die Power Taste, um das Gerät einzuschalten. Die Power LED leuchtet weiß. 8. Um die M.2 SSD zu deinstallieren, drücken Sie bitte erneut die Power Taste, um das IB-180MC-C31 auszuschalten (Power LED rot). Bitte warten Sie das Ende von Lese-/Schreibvorgängen ab, bevor Sie das Gerät ausschalten, um Datenverlust zu vermeiden.
Nos produits et emballages se recyclent, ne les jetez pas! Trouvez où les déposer sur le site www.quefairedemesdechets.fr © Copyright 2021 by RaidSonic Technology GmbH. All Rights Reserved The information contained in this manual is believed to be accurate and reliable. RaidSonic Technology GmbH assumes no responsibility for any errors contained in this manual.