Installation guide

ManualsBrandsICP ManualsCentral air conditionerOfficial ICP air conditioner heat pump outside unit

Table 1 - Accessory Usage

REQUIRED FOR LOW

AMBIENT COOLING APPLICATIONS REQUIRED FOR SEA COAST

(16 SEER Product Only) REQUIRED FOR LONG LINE APPLICATIONS 0Nithing 2

Accessory (Below 55°F/ 12,8°C) APPLICATIONS* miles/3,22km)

CompressorStart Assist

Capacitorand Relay NO No No

Crankcase Heater Yes,Standard Yes,Standard No

See Long Line Applications

Liquid LineSolenoidValve No Guideline No

SupportFeet Recommended No Recommended

Yes (Standardwith factory Yes (Standardwith factory Yes (Standardwith factory

Hard ShutoffTXV approved indoorunit) approved indoorunit) approved indoor unit)

Evaporator FreezeThermostat Yes No No

Low-Ambient Pressure Switch Yes No No

Isolation Relay Yes No No

For tubing line sets between 80 and 200 ft. (24.38 and 60.96 m) and/or 20 ft. (6.09 m) vertical differential, refer to Long Line Applications Guideline.

Table 2 - Refrigerant Connections and Recommended Liquid and Vapor Tube Diameters (In.)

RATED VAPOR

LIQUID up to 80 ft. (24.38 m)*

UNIT SIZE Connection Diameter Tube Diameter Connection Diameter Rated Tube Diameter

624, 924 3/8 3/8 3/4 3/4

636, 936 3/8 3/8 7/8 7/8

648, 948, 660, 960 3/8 3/8 7/8 1-1/8

Units are rated with 25 ft. (7.6 m) of lineset. See Specification sheet for performance data when using different size and length linesets.

Notes:

1. Do not apply capillary tube or fixed orifice indoor coils to these units.

2. For Tubing Set lengths between 80 and 200 ft. (24.38 and 60.96 m) horizontal or 35 ft. (10.7 m) vertical differential 250 ft. (76.2 m) Total Equivalent Length),

refer to the Long Line Applications Guideline.

EXPLOSION HAZARD

Failure to follow this warning could

result in death, serious personal

injury, and/or property damage.

Never use air or gases containing

oxygen for leak testing or operating

refrigerant compressors. Pressurized

mixtures of air or gases containing

oxygen can lead to an explosion.

Outdoor Unit Connected to Factory Approved

Indoor Unit

These outdoor units are carefully evaluated and listed with

specific indoor coils for proper system performance.

5. Remove adapter tube from bag and connect threaded

nut to liquid service valve. Tighten nut finger-tight and

then with wrench an additional 1/2 turn (15 ft-lb). DO

NOT OVER TIGHTEN!

Figure 3

Liquid Service Valve

--TEFLON ®SEAL

__L SWEAT/F LA RE

_L p_S_ONBo By ADAPTER

UID SERVICE VALVE

Install Adapter Tube

1. Remove plastic retainer holding outdoor piston in liquid

service valve.

2. Check outdoor piston size with matching number listed

on unit rating plate.

3. Locate plastic bag taped to unit containing adapter

tube.

4. Remove Teflon® seal from bag and install on open

end of liquid service valve. (See Fig. 3.)

Install Liquid Line Filter Drier Indoor

Refer to Fig. 4 and install filter drier as follows:

1. Braze 5 in. (127 mm) liquid tube to the indoor coil.

2. Wrap filter drier with damp cloth.

3. Braze filter drier to 5 in. (127 mm) liquid tube from

step 1.

4. Connect and braze liquid refrigerant tube to the filter

drier.

Specifications subject to change without notice. 428 01 1703 02