ICON lA yi 4-In / 4-Out Recording Fire wire Interface with MIDI & SOLIDIFY I/O a = AIRY ® C€ TF oneness
RET “Tha hiring Sash wth arrowhead symbol whe an /DIET— che trier dun mullah pou Sor do voltage rrp gs med at tha na fo emcee sng ars tartaric (weg) tint ve ree rear Ge sandstone fr dun ord nn ii Foot ott drat a pre) reds ord torsion resurgent papa | Important Safety instructions 1. Read all manufacturer's wakings and instructions 2. Do not use this apparatus near water. 3. Clean only with dry cloth. 4.
Contents Introduction What's in the package Features Front Panel Layout Rear Panel Layout Driver Installation Panel Control Minimum System Requirements.
Introduction Thank you for purchasing the ICON Fir Exon Digital Audio Interface. In these pages, you'll find a detailed description of all Fir Exon features, a guided tour through Its front and rear panels, step-by-step Instructions for Its setup and use, and full specification. You'll also find a warranty card In this package.
Features Basra 8, EE 1®®) an! ARE Yn The ICON Fir Exon mobile interface audio input and output module offers Fire Wire connectivity. Main features include: analog balanced I/O + Dual microphenefinstrument preambles with gain controls, LED metering, phantom power and input gain « Two analog inputs and four analog outputs on 1/4" TRS jacks « SOLIDIFY I/O on RCA coaxial connectors « Supports sampling rates from 44.
Front Panel Layout MIC/INST INPUTS Unbalanced Instrument and MIC level inputs. These hybrid connectors will accept a standard three-pin XLR plug or a 1/4" TS connector. CLIP LED When lit, this LED indicates clipping input level at the associated MIC/INST input. The LED will illuminate when the signal is 3dB below the clipping point. SIGNAL LED When lit, this LED indicates the presence of an audio signal at the associated MIC/INST input.
Rear Panel Layout —8, [SER ( POWER SUPPLY CONNECTOR Connect the 12VDC power supply to this jack using an AC adapter provided. @ SIPPED COAXIAL IN AND OUT CONNECTORS SOLIDIFY digital input and output on coaxial RCA connectors. The digital input is selected via the Fir Exon's control panel, while the digital output will be sent to the coaxial . @ MIDI IN AND MIDI OUT CONNECTORS MIDI input and output on standard 5-pin DIN connectors.
Driver Installation Please follow the below procedures step-by-step to install your Fir Exon and its driver. ' @ Turn on your computer Jp Note: Do not connect the Fir Exon to your computer yet uy @ Insert Driver CD to your CD-Rom After you have insert the provided [02 Driver CD into your CD-Rom, a T Installation screen should appear as Diagram 1, then click "Driver Installation" Fa yo Note: if the installation screen not appear automatically.
Driver Installation (continues) @® Connect your Fir Exon Connect your Fir Exon with the provided Fire wire cable. One end to the Fire wire port on the rear panel and the other end to your computer's Fire wire port. Also, plug in the provided power adapter to the Firestone tum on the power and choose "Next" @ Software Installation Window A window as illustrated as Diagram 4 would appear. Choose " Continue Anyway" Note: Although this message appear.
ARES —® Minstrel 1 & 2 Channels Input Mixer Adjust settings for Input Ch. Mic/Inst Line 3 & 4 Channels Input Mixer Adjust settings for Input Ch. Line SIPPED Channels Input (5 & 6) Mixer Adjust settings for Input Ch.
Hardware Connections « Connect the Fir Exon's outputs to your amplifier, powered monitors or surround system. For two-channel stereo operation, the default outputs are channels 1 and 2. However, you may change this in the Fir Exon control panel at your desire. For multi-channel surround output, connect up to four powered monitors to the Fir Exon's four analog outputs. Serer « If you are monitoring through headphones, connect one or two sets of headphones to the Fir Exon's headphone outputs.
Hardware Connections (continuous) ‘Sound Module MIDI Fr Master MIDI Controller = ell = [MDI MIDI Out Fire wire MIDI In MIDI Out AIRY Stacking Fir Exon You can stack one Fir Exon or any other ICON Reo Series gears on top of each other by simply lining up the bumpers.
Services If your Fir Exon needs servicing, follow these Instructions. 1. Ensure the problem is not related to operation error or textual system devices. 2. Pack the unit in its original packaging including end card and box. This is very important. If you have lost the packaging, please make sure you have packed the unit properly. ICON is not responsible for any damage that occurs due to non-factory packing. 3.
