UNPACKING Accessories included with the © Oy, (1) Microphone (HM-47) (8 Flat washers (M4) (2} Microphone hanger cable [OPCODE) . . Mounting nuts (M5} (3) DC cable {OPC 044A) . . 41 Flat washers (M5) @ Mounting bracket External speaker plug. .. (8) Taunting bracket knobs .
FOREWORD Thank you for selecting the ICON one of the most technologically advanced mobiles on the Land Mobile market today. Utilizing sophisticated computer-hasted technology and sitcom's precision: VHE/UHFE engineering, the incorporates state-of-thwart design concepts to meet the demanding needs of the Land Mobile user. TABLE OF CONTENTS INSTALLATION VEHICLE INSTALLATION: POWER REQUIREMENTS ANTENNA CONTROL FUNCTIONS. Ll 3 FRONT PANEL. REAR PANEL. OPERATION e L 5 RECEIVING TRANSMITTING HOBNOB FUNCTION.
1. INSTALLATION 1. Select a location that can support the weight of the transceiver; VEHICLE ‘INSTALLATION and-does not interfere with your driving in any way. 2. 'Place the mounting bracket in a suitable mounting location and mark the screw holes on the bracket. Make sure the controls and switches can be handled easily, and the display: can be clearly seen at the selected location: 3: :Drill: the holes apd mount the bracket as shown in the diagram: Tighten the screws.
1 The transceiver 15 ready 1o operate from any regulated 138V DC; pow Er RENOUNCEMENT 7A negative ground source. A 12V, negative ground system works well as a power spurge; s CONNECTIONS Pliny connector MZ To antenna cable A28V battery cannot be ‘connected to' the transceiver directly: Ask: your COM: Dealer or Service Niter for installation information if your vehicle has a 24V battery installed: ANTENNA g The single.
2. CONTROL FUNCTIONS FAG I EMPOWERMENT CONTROL Tums: ON and OFE ‘the transceiver and varies the audio output level: MONITOR SWITCH Turns the monitor function ON and OFF. {p.6) e TRANSMIT INDICATOR Lights up when the | transceiver is transmitting. {pa 7l CHANNEL SELECT SWITCH Selects an operating channel: MONITOR MIC CONNECTOR FOLLOWER] 3 VOLUME squelch SQUELCH CONTROL Sets the squelch threshold: level, initiating incoming weak signals. (p.
sett e e A LN ANTENNA CONNECTOR Connect Bn antenna here using @ PL-250 type connector. {p. 2] @\mé} Mo EXTERNAL SPEAKER JACK Accepts a2 4 B external speaker: .2 [ POWER CONNECTOR Connects: the supplied:power ‘cable 108 138V DC power source,” {p: 21 HORN CONNECTOR CABLES Conceits 1o an external hoer which gotchas an alarming optional UT-32 6r UT-23 5 installed. {p.
3. OPERATION {1} RECEIVER PRESETTING {1} Push the [MONITOR] SWITCH ON [IN position). 2 Rotate the [EMPOWERMENT] CONTROL clockwise. » [PERIL INDICATOR lights up: 3 ROTATE THE [SQUELCH] CONTROL fully counterclockwise, « [BUSY] INDICATOR lights up. Rotate the [POWER/VOLUME] CONTROL clockwise to a comfortable listening level 4] Rotate the [SQUELCH] CONTROL clockwise until the noise is quieted. This the threshold paint whore signals cdn be received.
{2). RECEIVING Nell The following procedures should be started after finishing (1) RECEIVER PRESETTING onp 5 D Push the MONITOR] SWITCH OFF {OUT position). (2) Choose a desired channel by using the [CHANNEL] SELECT SWITCH. (3 When a signal is received, the [BUSY] INDICATOR lights up and sound is.emitted from the speaker, @) Push the [MONITOR] SWITCH ON {IN petition) to activate the monitor function.
S frosty LN gee on The following transmitting procedures should be started-tater finishing the steps described in RECEIVING onp. B (1) Push the PTT SWITCH on the microphone to begin transmitting. s The [TX] INDICATOR lights up during transmission.
R ey When a signal with a correct code number is decoded. the transceiver taters the operator through & signaling device such as an automobile horn. This is useful ‘when the operator s away from the operating position. The optional UT-32 2.TONE DECODER UNIT or UT-33 2805TH, TONE DECODER: NET: must be installed 1o activate the HORN-HONK FUNCTION: e The optional HORN-HONK DRIVER UNIT: is recon: mended for connecting the transceiver to the signaling device.
5.
—— T —— eiCU400 UHE FM TRANSCEIVER SIC V100 VHF FM TRANSCEIVER ®IC-H16 VHE FM TRANSCEIVER ell-Ule UHF FM TRANSCEIVER sic-Uz UHF FM TRANSCEIVER S e AN The 1C-J400 is 5 18:channel UHE transceiver that is suitable for tse with the 1C:U200. " All 16 ‘channels can be easily programmed by using | ‘an’ external plugin Keyboard programmer. Additional Flexibility Is possible with ‘these ‘transceivers by using the CK.
e St AN ‘These options are available for base station use. oms-12 The DESK MICROPHONE has a monitor switch for increased DESK MICROPHONE operating convenience.
