Charger Connections Teletype Cigarette Z Lighter Socket External 13.8V DC Power Source *Use the DC power plug supplied with the transceiver.
ANTENNA CONNECTION Insert the connector on the flexible rubber antenna into the antenna connector on the top of the transceiver. Screw down securely. e Belt CLIP INSTALLATION Attach the belt clip to the back panel using the two supplied screws and plastic washers. ®HAND STRAP ATTACHMENT Spread open and slide the ring of the hand strap over either of the projecting loops on the sides of the transceiver. ATTACHMENT OF BELT CLIP AND HAND STRAP & Attach the belt clip on the back panel with 2:screws supplied.
(1) CONTROL Increases the audio level. T e VOLUME: (SQUELCH CONTROL Raises the threshold {elev. SQUELCH (3) CHANNEL SELECTOR SWITCH @) MONITOR SWITCH (B)ANTENNA CONNECTOR Rotate clockwise to turn the transceiver ON and increase the audio level, Sets the squelch threshold level. Rotate this control completely counterclockwise to turn QFF the squelch function, and clockwise to raise the threshold level. This switch selects Channel 1. {CH1) or Channel 2 CHICHI.
® EXTERNAL DC POWER JACK () EXTERNAL MIC JACK B EXTERNAL SPEAKER JACK @ TRANSMIT INDICATOR (0 RECEIVE INDICATOR GDPUSH.TOTALK [PTT) SWITCH (BATTERY PACK RELEASE BUTTON Connect the |C-CM1 CIGARETTE LIGHTER CABLE or external 13.8V DC power source to this jack for mobile operation. The battery pack does not need to be attached for operation of the transceiver. However, if the battery pack is attached, it charges simultaneously. The optional CM-9 or EM-46 SPEAKER-MICROPHONE.
43 CM-8 BATTERY PACK INTERNAL SPEAKER ) INTERNAL MICROPHONE 40 BATTERY CHARGE INDICATOR (I CHARGER TERMINAL A (CHARGER TERMINAL B (19 CHANNEL 2 MONITOR 10th CM-8 s a fully rechargeable Ni Cd battery pack that easily connects 1o the 1IC-U2. {Optional extra) The 1C:U2's internal speaker will operate when the transceiver is receiving. However, it will not operate if an external speaker is connected to the EXTERNAL SPEAKER JACK. The 1-U2's internal microphone will operate when the transceiver is transmitting.
®RECEIVING 1) Rotate the ON-OF F/VOLUME CONTROL clockwise to turn the power ON, 2} Rotate the SQUELCH CONTROL fully counterclockwise and then push [N the MONITOR SWITCH. 3) Adjust the CONTROL to a comfortable fastening level. 4} Rotate the SQUELCH CONTROL clockwise until the noise is quieted. This is the threshold point where signals can be received. §) Push OUT the MONITOR Switch to turn. ON the monitor function. 6) Set the CHANNEL SELECTOR SWITCH 1o select the desired channel.
SECTION 5 GENERAL SPECIFICATIONS « CHANNEL SPACING ¢ NUMBER OF CHANNELS « COMPLIANCE s APPROVED NUMBER s AF POWER OUTPUT «RF POWER OUTPUT 12.6kHz 16 MPT 1301 RTD3195 (IC-H16) RTD3282 (1C-U16) 0.5W SEE TABLE ON PAGE 32 1-u2 12.5kHz 2 MPT 1301 RTD3386 0.
SECTION 6 ACCESSORIES (OPTIONAL) 8 |C-CM1 CIGARETTE LIGHTER CABLE o Cm-4 BATTERY CASE s Cm-35 AC BATTERY CHARGER e Cm-9, EM-46 SPEAKER-MICROPHONE ®CARRYING: CASES S CM-16E WALL CHARGER ®CM-25E WALL CHARGER ®HS-10: HEADSET #HS-10SA VOX UNIT ®HS-10SB PTT SWITCH BOX Plugs into cigarette lighter socket to charge CM-3, CM-BA, CM-7 or CM-8. or to operate unit from car battery. For AA size Ni Cd or dry batteries. Charges all ICON battery packs. Charges CM-3 in 15 hours, CM-2, CM-5, CM:5A and CM-7 in 1.
