UNPACKING 1) Mounting bracket @) External speaker . o O Microphone hanger ground mg ead i w DC power cable (B Mounting sellotaping screws & Mounting sowers | ) Flat washers B Mountings 18 Mare fudges, L s’G Allen kay o (7 Microphone hanger Q Mounting bracket resews.
FOREWORD i | i Thank you for your purchase of the ICON IC-V1004C-U400, the most technologically advanced and sophisticated VHFE/UHE mobiles an the Land Mobile market today. Utilizing sophisticated computer based technology and sitcoms precision VOUCHER engineering, the E incorporate state-of-the-art design concepts ta meet the demanding needs and require meets of the Land Mobile user, TABLE OF CONTENTS £ i* SECTION 1 INSTALLATION 1 . 1.1 VEHICLE INSTALLATION 122 POWER REQUIREMENTS .
SECTION 1 INSTALLATION 1-1 VEHICLE INSTALLATION {11 Select & location which can support the weight of the unit, and dogs not interfere with the driver in any way. @) Place the mounting bracket in the mounting location and mark the bracket's screw holes.: Confirm the controls and switches can be handled easily, and the display seen clearly in the selected location. @ Drill the hales, @) Mount the bracket as shown in the diagram. Tighten the screws. Supplied mic hanger ground S hanger.
1:2 POWER REQUIREMENTS The transceiver is supplied ready to operate from any regulated 13.8V DC, 10A negative ground source. An automobile 12 vale, negative ground system works well as a power source. CAUTION: Voltage greater than 15 volts DC will damage your transceiver, Check the source voltage before connecting the power cable. U400 REAR PANEL SUPPLIED: DG POWER CORD PL-259 FUSE {154} AN £3 69 The 24V Battery cannon be connected 1o the transceiver 12V BATTERY directly.
4 POWER SWITCH [POWER] (2)VOLUME CONTROL [VOLUME] 3 CHANNEL UP/DOWN SWITCHES 4)SCAN SWITCH [SCAN PRIORITY S Witch [PRO] &)SQUELCH SWITCH [S0L] (SCAN CHANNEL SELECT SWITCH [BESSEL] (8 SQUELCH THRESHOLD LEVEL CONTROL [sQL] @ PRIORITY CHANNEL SELECT SWITCH [P-SEAL] {0 MICROPHONE CONNECTOR SCREW 11 MICROPHONE CONNECTOR Turns the power to the transceiver ON and OFF, Rotate clockwise to increase the volume level.
UNCTION DISPLAY © 123456789 B e F'r' ’“Ta W12 13141518 ”TONE= B CALL= ® A BUSY INDICATOR “RX appears when receiving signal: B TRANSMIT INDICATOR '"T X' appears when transmitting. (€ SCAN CHANNEL INDICATOR The programmed channel numbers 1, 2,3 16" appear. The priority channel blinks when scanning: © TONE INDICATOR TONE' appears when an individual phone is programmed 1o operate on one of the channels.
ANTENNA CONNECTOR 45 HORN CONNECTOR (D SPEAKER JACK G5 POWER CONNECTOR Connect an antenna connector here, CAUTION: Transmitting without an antenna may damage the transmitter. Connects to an external horn which acts assn alarm. A vehicle hom may be used for this purpose when an optional UT:26 DECODER UNIT or UT-27 2805Hz TONE DECODER UNIT i installed. Connects to the supplied 1C-8P5 speaker, Connects to the supplied power cable.
LTS TN R govt RECEIVING @ Push [POWER] SWITCH ON. @ Push [SQUELCH] SWITCH and adjust [VOLUME] 12348 T80 TONE W =] L CONTROL: Push [SQUELCH] SWITCH again: LIBRAS Tone ch G Signal received cannelloni 8. 12345607 B 90 NAR T4 1518 il Verity that the [POWER] SWITCH js OFF and the microphone is in the microphone hanger before connecting power to the transceiver. () Push the [POWER] SWITCH ON {N position). {2)Push the [SOL] SWITCH OFF ("RX' appears on the display).
i 3-2 TRANSMITTING ) Press [SWITCHBACK. 12394567 8990111313 14 1516 1 a TONE oo {2) Breathtaking microphone. 31 Release [PTT] SWITCH. 3-3 SELECTING CHANNELS () Push [UP] SWITCH. 1234887891011 1213 1415 96 TINE DOWN: CHANNEL Use either the [UP] or [DOWN] SWITCHES, (1) Press the [PTT] (push-to-talk) SWITCH to begin transmitting. YTX and “TONE' appear on the display to indicate a signal is being transmitted. NOTE: It individuation tone is programmed. "TONE' does not i appear.
3-4 SCANNING 1) Adjust [VOLUME] CONTROL and push [SQUELCH] SWITCH. D " cnn | HRX disappears. 2} Push the [SCAN] SWITCH. tithe scan:will stopping: the transceiver receives assign; The provides either PRIORITY SCAN of STEP SCAN.: These scan afflictions can be set by your nearest authorized ICON Dealer to suit your operating purposes. SCAN: Eliminates the need for channel searching by automatically monitoring programmed channels. The scan will stop at a channel on which a signal is received.
i (1) Priority scan note P.CH: Priority Channel {mwm Priority channel blinks Step scan note A 1 123486783101 RIBBER Decimal point blinks The priority channel feature allows easy monitoring of your most important channel while still fastening for signals or the other programmed channels. 1) The small number at the top of the FUNCTION DISPLAY is the priority channel number. The priority channel can be changed to suit your aerating purposes.
PROGRAMMING THE PRIORITY CHANNEL 47 Remove the microphone connector. §123456789mu . ch () Select priority channel. Push [P-SELL SWITCH. 123456789 10111212 Push [PRO] SWITCH to check the priority channel: 12034 56781990 iy bind e Prn o channel indicator @) Replace the microelectronics. L NOTE: The priority channel cannot be programmed when STEP SCAN has been set in the transceiver. | A small __number at the top of the FUNCTION DISPLAY appears when PRIORITY SCAN has been set.
3.6 PROGRAMMING THE LOCKOUT CHANNEL ) 1 Remove microphone connector: ) Sleet channel {Example) Seigneur channel 7 for lockout. © Push: [BESSEL] SWITCH! “misapprehends. TOSS Push [S-SEAL] SWITCH again 1o return ‘to' the normal operating channel. 7 % appears gain; 323456789 101112:331815 cri ! 3:7 MONITOR FUNCTION | LOCKOUT FUNCTION: The purpose of the lockout definition is to disable specific channels so, when scanning, the transceiver does not stop on these channels.
