3 PANEL DESCRIPTION M Remote controller front panel R “tetanus O Vitreous: O N’ = Turret © O INTERNAL SPEAKER Operates:when: ihe: transceiver is receiving ‘writhe inter: com is operating. €) MIC CONNECTOR Connects the supplied microphone o ap atonal HS HANDSET here. € ALARM SWITCH [ALARM {p. 19) « Tuns ON and OFF the alarm function. = Transmits salami signals: when : pushing this switch together with {TX FREQ). € 2182 kHz SWITCH [2182kHz] (p. 19) Selects “the: 2182 KMz emergency.
PANEL DESCRIPTION 3 HE MARINE TRANSCEIVER PO ANTENNA TUNER SWITCH [TUNE] (p. 16) Starts the tuning of the AT-120 HF AUTOMATIC ANTENNA. TUNER (optional). @CLEAR ENTRY SWITCH [CE] (p. 14) « Clears an entry and retrieves the previous key input.
M Transceiver rear panel PANEL DESCRIPTION @ o@D @ @money 2le e . amm e Sidle) @ ANTENNA CONNECTOR [ANT] (p. 10} Connect an antenna cable here! A PL259 ormolu must be' used. €) GROUND TERMINAL 10} To: ‘prevent Electrical’ shocks] interference’ from! other electronic: equipment, and other. problems, be: rude to ground the transceiver to a good Garth point € ACCESSORY SOCKETS (p: 12) Input: and output: signal for: textual: equipment con: sections. M Function display Wolsey FREQUENCY INDICATOR (p.
M Emote controller connections Tne remote controvert needs 2 kinds of cable connections: « Supplied interlace cable (CAPETIAN Supplied: DG power cable (OPCODE) 1) Interface cable The cable s connectable hastiness the controller and the transceiver. Ses the diagram below: Since thesis an optical fiber cable, + RO NOT: force endear he cable too strongly: = DONOR cuter 11y o lengthen the cable. {2) DC power cable Conn act the Cabin t0:a 12V DC power source (al east TA) directly. See the diagram below. and .
Bl 5 EXTERNAL EQUIPMENT CONNECTIONS M AT-120 HF AUTOMATIC ANTENNA TUNER @ AT-120 cable connections Antenna wire 5002 cranial sable AT120 antenna tuner GUMBOOT transceiver: off ANTENNA e == TUNER b i CONNECT! o Ground 4-conductor central caliper Jar @ Control cable connections N START =0 Q\R% A M ANTENNA MARCHERS @ Connecting a wire with wire clamps @ Typical installation Wire clamps: o insulator @ Using the with a long wire antenna Admitting wire W00 MN:AG0 oF MN-100L.
SETTING A FREQUENCY 7 Il COMITY MG oo HEE) BEE CFD 050 Diagrammed shows the larder for setting frequency, M Setting a frequency NOTE: The displayed frequency clears and & new frequency: is stored in the displayed memory channel when operating on & memory. channel between 1160 and continuing with the follow: ing procedures, I channels are fixed and cannot be hanged o cleared. Bl Push (CE). *The CE indicator lights. Enter the desired frequency in kHz using the keyboarder.
10 WRITING A FREQUENCY H B 2808 EEo, 'GCC The:diagram shows: the order Jor waiting & frequency into'a memory channel. W Writing a frequency The 1G:M800 has 160 user-programmable memory channels: M Writing a comment Capitol 7 characters can be 'snored in 'gate memory Bl Science the desired memory chanson to be stored. channel for your reference. * For selecting a memory channel, sae p. 14, i Pisa [FUN then push [CE]. »The ‘cursor ‘appears: under ' the ‘character in the bottom st corner.
OPERATING THE SCAN 111 ‘The diagram shows:the order for operating the groan, M Scanning The transceiver 'scans desired memory ‘channels: ha tween 12160 :Bean channels are sel as follows: S Select the desired memory chansons 10 be scanned: * For selecting memory channel, sea 0. 1% JE Rush (BEL] to Set the channel 3s 4 Scan chanticleer. » %M appears: 151839 § (Wolsey M Push [SCAN] o start the scan: #CANCAN appears: ¥ Scanning does not 'stop vane when signalizes received: 13183.
SETTING THE DISPLAY CONTRAST 1 3 CRUET R o The:diagram: shows: the order for changing the display contrast. M Changing the display contrast The:contrast: of idisplayed:icharaciers: can b varied:in 7 pitapat. Change the .
INTERCOM OPERATION (OPTIONAL) 15 a (v} Tr men E.E B Operating the intercom function The Intercom: function ‘allows vou 1o talk o the deck from the cabin or vice versa. Mare than 2 controllers {(optional) are. necessary for using this function: H Rush [DUNCE Push [MOREL + L INTERCOM “ appears, == INTERCONNECT o Bl push aad hold the PTY switch on the microphone and Spookiness the microphone, *Countervail is transferred to either controllers: Fastidious audio: revel through the speaker on ihe receive.
MAINTENANCE 17 HER M Replacing a fuse i the fuse blows or the transceiver stops functioning, find The BAMBOO has fuses installed in 3 different places: the ‘spruce: of the ‘problem it possible; and: replace: the Transceiver DG power cable: SAN'A damaged: fuse with ‘a’ new, rated: fuse. | See diagrams = Contractile DG power tabla: 13 A below for relapsing the fuse. “inside the transceiver i5A (Transceiver bottom view} M Installing an optional FL-32A filter 1 Unscrew 10 resows and sift up: the MAIN unit: 3.
CHANNEL chart 19 R User-programmable memory channel CHANNEL NUMBER DESCRIPTION Fr:160 User-programmable memory channel! MITE channel list (SSB) CHANNEL NUMBER DESCRIPTION 401427 4 MH2 ITU duplex channel tor 568 $14g 4 MMz ITU simplex channel! for S8B 801608 §: MMz ITU duplex channel for 888 61289 8:MHz ITU simplex channel for 558 80174832 8 MHz ITU duplex channel] fot SSB 8189 8 Mz iTU simplex channel for 558 1201241241 12 MHz ITU duplex channel for 888 142 MHz 1TU: simplex annals for SSB: 1601 -+1856 16 MH
