IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to-operate the transceiver: SAVE THIS INSTRUCTION manual contains important safety and operating instructions for he {G-M700PRO 598 RADIO TELEPHONE: EXPLICIT DEFINITIONS The explicit definitions described below apply to this instruction manual, Personal: injury;: fire: hazard: ot semicircular shopaholic ool Equipment damage may our.
IN CASE OF EMERGENCY (fof maritime operation) I your vessel requires assistance, contact other vessels and the Coast Guard by sending a distress call on 2182 kHz! VERSIONS The following: versions are available ‘forehead 16 MT00PRO. 2182 kHz 2-tone alarm s built-ING CALFSKIN narrow filter is optional.
| TABLE OF CONTENTS IMPORTANT @y 1 EXPLICIT DEFINITIONS « i PRECAUTIONS i i IN-CASE OF EMERGENCY.
OPERATING RULES AND GUIDELINES 1 L CALL PROCEDURES Calls must be proper identified and time limits must be respected. Di Give our call sign each time you call anther vessel o coast station. If you have no call sign, identify your vessel name and the name'of the licenses. © Give your call sign &t the end of each transmission philatelists more: fan 3 min. & You must break and give your call sign concertmaster ‘very 15 min. during long ship-to-shore calls, @ Keep your unanswered calls short, less than 30 sec.
2 PANEL DESCRIPTION M Front panel 1t RADIO! Vs ERMINE © MICROPHONE CONNECTOR (p. 16) Accepts: the supplied microphone ot an optional handset, v NOTE! No juridic fs output via the speaker when the microphone handsets interconnected. B POWER SWITCH [POWER] Turing power on and ot © SPEAKER SWITCH [SPEAKER] Turns the bully-in speaker o and off. * MUk appears in 1Be display while the speaker is lured off, *Any external speaker connected to the rear pane is not ned off.
.| 2 PANEL DESCRIPTION M Display | SQL NB SCAN © ALARM INDICATOR (p. ii) Appears when the alarm function is activated such as for an alarm foster distress anal transmission. *Nut available in General version. © RECEIVE INDICATOR Appears wheels receiving and when the squelch open. © TUNE INDICATOR (p. 8} Flashes while the connected antenna finer, such as loom's AT-130, i being tuned, *Tuning stairs whets transmitting on a new frequency or pushing the {TUNE] switch.
SELECTING A CHANNEL/FREQUENCY 3. M Memory Modesto mode The transceiver has 2 operating modes: memory mode and \VEO mode: Memory mods is used 1o select reprogrammed mating channels in one of the S channel groups; VFO mode is used 1o select frequencies around reprogrammed channels. Push [CHEERER] to toggle between memory.and YFO. modes. » FREQ appears whom i VEQ mode: *Info mode only: simplex operation is possible: MW Selecting a channel The transceiver has 1150 channels divided into' 3 groups of 50 {max.
. 3 SELECTING A CHANNEL < Scan function e The scan function:allows you 1o automatically search channels within a group for signals. There are 2 scan Pipes (delectation inset mode) as follows: Channel scan Sean palsies for 30 sec after 1he squelch opens, then resumes Shari operation D Rotate the [GROUT] selector to select the groin you wish o Sean. @ Pushily] 1o close the squelch i necessary. »'SQL appears: @ Push [SCAN] to start scanning: *SCAN appears. @ Ash SCAN] again stop scanning. +SCAN disappears.
SELECTING A CHANNEL 3 M Resetting the CPU Under some circumstances the transceiver's internal GPU may cause erroneous indications ors the display 1f his happens, reel the CPU as fallows: While pushing [ENT] £10]; push [POWER] 1o urn Group A, channel 1 s power on: o HALE o 21 collected after resetting «The CPU s resetting the display.
M Functions for receive RECEIVE AND TRANSMIT 4 < Squelch function The squelch function detects signals withhold com: orients and squelches (mutes) unwanted signals stitch as unmotivated: veal signals. Providences wist standby. When you need 1o receive weak signals, the squelch should be turned off. PushiSQLToitougle the friction on and off.
10 4 RECEIVE AND TRANSMIT W CW operation The transceiver has the Hollowing CW keying features electable in set mode as described on page: 12 e Elul Break-in (receiving is possible while transmitting) we. Delay keying (automatic transmission with keying) w Off (biannual transmission is necessary before keying} @ Connect a CW keyed or an external electronic Kaye 1o the ACACIA) socket as showboat right @ Select the devised channel o operate CW-mode. @ When the selected channelization in.
SET MODE 5 W Set mode operation Set:mode operation is used for programming infrequently changed values or conditions of functions: £ NOTE: Some of the set mode stems described in this section are not available on some transceiver versions: (1 Push [PowerPoint tum power ol If necessary, 2 While pushing [ENT] 4 [1]; push: [POWER] totem power on and enter set mode: 3 Rotate the [GROUP] selector 1o select the desired fam. @ Rotate the [CHANNEL selector set the values or conditions farther selected item.
CONNECTIONS AND INSTALLATION B Connections on rear panel Optional A-130 @ ANTENNA CONNECTOR {p. 19§ Connects band antenna with 2 50 Q matched convivial cable and & PL-259 glop: @ GROUND TERMINAL IMPORTANT! Connects ‘a ship's: {or vehicle's) ground. See p. 18 for details, € ACCRA) and SOCKETS See p. 16 Tor details. O CLONE JACK For Dealer use only. © REMOTE SOCKET (p.17) EMOTE socket for Marin and General versions, O EXTERNAL SPEAKER JACK Connects a 4-16 Q external speaker using a ¥" monaural plug.
18 6 CONNECTIONS AND INSTALLATION M Ground connection The transceiver and antenna tuner MUST have an adequate logrolling connection. Otherwise, the overall efficiency of the transceiver and antenna tuner install elation will be reduced. Electrolysis, electrical shocks and interference from other equipment could also oG For best results; use the heaviest gauge wire or strap available and make the connection ag shore as posts: ble. Ground the transceiver and antenna tuner one.
B CONNECTIONS AND INSTALLATION W Mounting ¥ WARNING: NEVER mount the Transceiver overhead: The weight of the transceiver is approximately: ginkgo. bullish apparent weight will increase several fold due to wave shocks or vibration. The fragrant caver must be mounted on a flat, hard surface. < Mounting location Select a location that provides easy access fo the front panel for navigation safety, has good ventilation and is not subject ta Sea spray.
M Installing internal options CONNECTIONS AND INSTALLATION © < Opening the case Follow the case and cover opening procedures shown: Here when you want 1o install adoption or adjust & setting for noncom tuner control < Remove the 9 screws from the rear panel; then remove the rear frame and rear sealing. @ Remove the transceiver case. @ When reassembling the transceiver, check the following points; = internal cancan slits in the case are on the same: side.
