INSTRUCTION MANUAL VHF DIGITAL TRANSCEIVERS iF3210D Series UHF DIGITAL TRANSCEIVERS iF4210D Series This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. The photo shows the VHF transceiver.
FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL— This instruction manual contains important operating instructions for the IC-F3210D VHF DIGITAL TRANSCEIVER and the IC-F4210D UHF DIGITAL TRANSCEIVER. See the operating guide for details of IDAS (ICOM Digital Advanced System) system operations. Ask your dealer for details. EXPLICIT DEFINITIONS WORD DEFINITION RDANGER! Personal death, serious injury or an explosion may occur.
FCC INFORMATION • FOR CLASS A UNINTENTIONAL RADIATORS: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PRECAUTIONS R DANGER! NEVER short the terminals of the battery pack. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom chargers. Only Icom battery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause smoke, fire, or cause the battery to burst.
DO NOT modify the transceiver. The transceiver warranty does not cover any problems caused by unauthorized modification. DO NOT use harsh solvents such as benzine or alcohol when cleaning, as they will damage the transceiver surfaces. BE CAREFUL! The transceiver will become hot when operating it continuously for long periods of time. KEEP the transceiver away from heavy rain, and never immerse it in the water. The transceiver meets IP54* requirements for dustprotection and splash resistance.
VOICE CODING TECHNOLOGY The AMBE+2™ voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment.
TABLE OF CONTENTS FOREWORD................................................................................... i EXPLICIT DEFINITIONS................................................................. i FCC INFORMATION.......................................................................ii PRECAUTIONS..............................................................................iii VOICE CODING TECHNOLOGY................................................... v SUPPLIED ACCESSORIES.................................
1 ACCESSORIES ■■Accessory attachments DD Flexible antenna Connect the flexible antenna to the antenna connector. CAUTION: • NEVER carry the transceiver by holding only the antenna. • DO NOT connect the antenna other than listed on page 34. • Transmitting without an antenna will damage the transceiver.
ACCESSORIES 1 1 2 DD Belt clip To attach the belt clip: ➥➥ Slide the belt clip in the direction of the arrow until the belt clip locks in place, and makes a ‘click’ sound. 3 4 5 Belt clip 6 7 Battery pack 8 9 10 11 12 To detach the belt clip: qq Remove the battery pack from the transceiver, if it is attached. (p. 3) ww Lift the tab up (q), and slide the belt clip in the direction of the arrow (w).
1 ACCESSORIES DD Battery pack or case To attach the battery pack or case: qq Fit the battery pack/case in the direction of the arrow, then close it. ww Hook the latch until it makes a ‘click’ sound. q Battery pack/case w Latch To remove the battery pack/case: Be careful! The latch is tightly locked, so use caution when releasing it. DO NOT use your finger nail. Use the edge of a coin or screwdriver tip to carefully release it. q Unhook the latch.
ACCESSORIES 1 1 NEVER remove or attach the battery pack/case when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver, battery pack/case, and may result in them being damaged. NOTE: Keep the battery terminals clean. It’s a good idea to occasionally clean them. 2 3 4 5 6 DD Jack cover 7 Attach the jack cover when optional equipment is not used. To attach the jack cover: qq Attach the jack cover to the [SP MIC] jack. ww Tighten the screws.
2 PANEL DESCRIPTION ■■Front, top and side panels q ROTARY SELECTOR i ANTENNA CONNECTOR u PTT SWITCH y UPPER KEY t LOWER KEY w VOLUME CONTROL e LED INDICATOR Speaker r SPEAKERMICROPHONE JACK Microphone q ROTARY SELECTOR Rotate to select the preprogrammed memory channels or TX Status list number*, depending on the preprogrammed. *Digital operation only w VOLUME CONTROL [VOL] Rotate to turn the power ON or OFF, and adjust the audio level.
PANEL DESCRIPTION 2 1 e LED INDICATOR (p. 7) ➥➥ Lights red* while transmitting. * When the attached battery type is set to “Alkaline Dry,” the LED indicator lights orange. ➥➥ Lights green while receiving a signal, or when the squelch is open. ➥➥ Lights or blinks orange while receiving a status call, a SDM (Short Data Message) or a Call Alert call. r SPEAKER-MICROPHONE JACK [SP MIC] Connect the optional speaker-microphone or VOX adapter cable.
2 PANEL DESCRIPTION ■■LED indicator The LED indicator indicates the status of various parameters of the transceiver as follows; (Reference: R=Red, G=Green, O=Orange) • TX: Lights while transmitting a signal. R* • RX: Lights while receiving a signal. G • Scan: Blinks when the scan is activated. G G • Low Battery 1: You should charge the battery. (blinks slowly) G G • Low Battery 2: You must charge the battery. (blinks fast) G G G G • TX low Battery 1: Low Battery was detected during TX mode.
PANEL DESCRIPTION 2 1 2 3 4 • Call LED (ON): Turns ON while receiving a status call, a SDM (Short Data Message) or a Call Alert call, depending on the preprogramming. 6 7 O • Call LED (Blink): B links while receiving a status call, a SDM (Short Data Message) or a Call Alert call, depending on the preprogramming. O 5 O • Success: Blinks slowly when your call is successful. O G • Failure: Blinks slowly when your call fails, or it is refused.
2 PANEL DESCRIPTION ■■Programmable function keys The following functions can be assigned to the [Upper] and [Lower] programmable function keys. Consult your Icom dealer or system operator for details concerning your transceiver’s programming. NOTE: The function keys for the digital mode are described in the operating guide. SCAN START/STOP Push to start and cancel the scanning operation. • W hen the scan started with the Power ON Scan or Auto Scan function, push to pause the scanning operation.
PANEL DESCRIPTION 2 1 MEMORY CHANNELS 1, 2, 3, 4 Push to directly select memory channel 1, 2, 3 or 4, if programmed. Consult your dealer for details. MONITOR Push to turn the CTCSS (DTCS) squelch Mute ON or OFF. LOCK Hold down to electronically lock all programmable keys except [Moni], [Lock], [Emergency]*, [Surveillance], [Siren] and [Lone Worker]*. * For digital operation. See the operating guide for details. HIGH/LOW (p.
2 PANEL DESCRIPTION ■■ Programmable function keys (Continued) SURVEILLANCE ➥➥ Push to turn OFF the Surveillance function. ➥➥ Hold down to turn ON the Surveillance function. • When this function is turned ON and a signal is received, the beep is not heard and the LED does not light even if a key is pushed. SIREN Hold down for 1 second to emit a siren sound. This function can be used for situations other than an emergency alert, such as a security alarm for example.
BASIC OPERATION ■■Turning power ON 3 1 Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. (p. 21) [VOL] ➥➥ Rotate [VOL] to turn power ON. 3 4 5 DD Battery type selection The battery type must be selected according to the battery pack or case when it is changed, but only the first time it is used. Check the battery type before you begin the selection procedure.
3 BASIC OPERATION ■■Channel selection There are several ways to select channels, and they may differ, depending on your system set up. To select a desired operating channel, do one of the following. • Rotate [ROTARY SELECTOR]. • Push one of memory channel keys, [MR-CH 1] to [MR-CH 4]. • Push one of these keys, [Prio A], [Prio B], [Prio A (Rewrite)] and [Prio B (Rewrite)]. AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type.
BASIC OPERATION 3 ■■Receiving and transmitting CAUTION: Transmitting without an antenna will damage the transceiver. See page 1 for antenna attachment. Receiving: qq Rotate [VOL] to turn ON the power. ww Rotate [ROTARY SELECTOR], or push one of the memory channel keys, [MR-CH 1] to [MR-CH 4], to select a channel. ee When receiving a call, adjust the audio output to a comfortable listening level. Transmitting: Wait for the channel to become clear to avoid interference.
3 BASIC OPERATION ■■ Receiving and transmitting (Continued) DD Transmitting notes • Transmit inhibit function The transceiver has several inhibit functions, which restrict transmission under the following conditions: - The channel is busy. However, depending on the preprogrammed settings, you can transmit when the call includes an unmatching (or matching) CTCSS (DTCS), RAN code*, or Individual or Talkgroup ID*.
BASIC OPERATION 3 ■■Setting the microphone gain 1 Adjusts the microphone gain. 2 qq Rotate [VOL] to turn the trans[ROTARY SELECTOR] ceiver power OFF. [VOL] ww Set [ROTARY SELECTOR] to Channel 16. ee While holding down [Upper], rotate [VOL] to turn ON the power and enter the microphone gain adjustment mode. rr Push [Upper] to increase, or push [Lower] to decrease the [Upper] microphone gain. [Lower] • The adjustable range is 1 (minimum) to 4 (maximum).
3 BASIC OPERATION ■■Setting the squelch level The squelch circuit mutes the received audio signal, depending on the signal strength. qq Rotate [VOL] to turn the trans[ROTARY SELECTOR] ceiver power OFF. [VOL] ww Set [ROTARY SELECTOR] to any channel other than Channel 16. ee While holding down [Upper], rotate [VOL] to turn ON the power and enter the squelch level adjustment mode.
BASIC OPERATION 3 ■■Setting the Beep level 1 The beep function can be turned ON or OFF, and its level can be adjusted between 1 and 5, or 1 (linked) and 5 (linked). When a Linked option is selected, the beep level is adjusted with [VOL]. qq Rotate [VOL] to turn the trans[ROTARY ceiver power OFF. ww Set [ROTARY SELECTOR] to SELECTOR] any channel other than Channel 16. ee While holding down [Lower], rotate [VOL] to turn ON the power and enter the beep level adjust[Upper] ment mode.
3 BASIC OPERATION ■■Setting the Ringer level The Ringer level can be adjusted between 1 and 5, or 1 (Linked) and 5 (Linked). When a Linked option is selected, the Ringer level is adjusted with [VOL]. qq Rotate [VOL] to turn the trans[ROTARY ceiver power OFF. SELECTOR] ww Set [ROTARY SELECTOR] to Channel 16. ee While holding down [Lower], rotate [VOL] to turn ON the power and enter the Ringer level adjustment mode.
BASIC OPERATION 3 ■■Output power level selection If the transceiver has [High/Low] assigned to it, the transmit output power level can be selected. When the battery case is selected as the battery type, or the battery voltage drops to a low power level and the LED indicator status is “Low Battery 2,” the output power automatically switches to “Low 1.” (pp. 7, 12) ➥➥ Push [High/Low] to select the transmit output power level. • One beep sounds when “Low 1” is selected.
4 BATTERY CHARGING ■■Caution (for the BP-264 ni-mh battery) R DANGER! NEVER short terminals (or charging terminals) of the battery pack. Also, current may flow into nearby metal objects such as a necklace, so be careful when placing battery packs (or the transceiver) in handbags, etc. Simply carrying with or placing near metal objects such as a necklace, etc. may cause shorting. This may damage not only the battery pack, but also the transceiver. R DANGER! NEVER incinerate used battery packs.
BATTERY CHARGING 4 1 If your Ni-MH battery pack seems to have no capacity, even after being charged, completely discharge it by leaving the power ON overnight. Then, fully charge the battery pack again. If the battery pack still does not retain a charge (or only very little charge), a new battery pack must be purchased. (p. 33) Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation.
4 BATTERY CHARGING ■■Caution (for the BP-265 Li-ion battery) Misuse of Li-ion batteries may result in the following hazards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! NEVER short terminals (or charging terminals) of the battery pack. Also, current may flow into nearby metal objects such as a necklace, so be careful when placing battery packs (or the transceiver) in handbags, etc.
BATTERY CHARGING 4 1 R DANGER! NEVER incinerate used battery packs, since internal battery gas may cause them to rupture, or may cause an explosion. 2 3 R DANGER! NEVER solder the battery terminals or NEVER modify the battery pack. This may cause heat generation, and the battery may rupture, emit smoke or catch fire. 4 R DANGER! Use the battery only with the transceiver for which it is specified.
4 BATTERY CHARGING CAUTION: Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50˚C; +122˚F) for an extended period of time. If the battery must be left unused for a long time, it must be detached from the radio after discharging.
BATTERY CHARGING 4 ■■Battery chargers 1 DD Using the BC-191 to rapid charge the BP-264 2 The BC-191 provides rapid charging of the Ni-MH battery pack (BP-264 only). Never use it for any other battery pack. Charging time: Approximately 2 hours (for the BP-264) The following item is additionally required: • An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-23L).
4 BATTERY CHARGING DD Using the BC-192 to regular charge the BP-264 The BC-192 provides regular charging of the Ni-MH battery pack (BP-264 only). Never use it for any other battery pack. Charging time (with BC-147S): Approximately 16 hours (for the BP-264) The following item is additionally required: • An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L).
BATTERY CHARGING 4 DD Using the BC-193 to rapid charge the BP-265 The BC-193 provides rapid charging of the Li-ion battery pack (BP-265 only). Never use it for any other battery pack. Charging time: Approximately 2.5 hours (for the BP-265) The following item is additionally required: • An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-23L).
4 BATTERY CHARGING DD Using the BC-197 to rapid charge the BP-264 or BP-265 The BC-197 rapidly charges up to six battery packs. Charging time for the BP-264: Approximately 2 hours Charging time for the BP-265: Approximately 2.5 hours The following additional item is required: • An AC adapter (not supplied with some versions) or the DC power cable (OPC-656) Battery pack Transceiver Turn OFF the power Charger adapters* are installed in each slot.
BATTERY CHARGING 4 1 There are two types of BC-197 chargers for the IC-F3210D series or IC-F4210D series transceivers. One is for Ni-MH batteries, and the other is for Li-ion batteries. Before you purchase a BC-197, check the type of battery you are using, and then be sure to choose the suitable charger.
4 BATTERY CHARGING IMPORTANT: Ensure the tabs on the battery pack are correctly aligned with the guide rails inside the charger.
BATTERY CASE ■■Optional battery case (BP-263) 5 When using the optional battery case, install 6 AA (LR6) size alkaline batteries, as illustrated below. qq Remove the battery case, if it is attached. (pp. 3, 4) ww Install 6 AA (LR6) size alkaline batteries. • Install only alkaline batteries. • Be sure to observe the correct polarity. 1 2 3 4 5 6 7 Be careful! The negative terminals of the battery case protrude from the body, so pay attention not to injure your fingers when inserting the batteries.
6 OPTIONS DD BATTERY PACK Battery pack Voltage BP-263 BP-264 BP-265 Capacity Battery life*1 Battery case for 6 AA (LR6) alkaline 7.2 V 7.4 V 1400 mAh (typ.) 1900 mAh (min.) 2000 mAh (typ.) —*2 VHF 12 hrs. UHF 11 hrs. VHF 17.5 hrs. UHF 16 hrs. *1 When the power save function is turned ON, and the operating time is calculated under the following conditions: TX : RX : standby = 5 : 5 : 90 *2 The average operating time depends on the alkaline cells used.
OPTIONS 6 • BC-197 multi-charger For rapid simultaneous charging of up to six battery packs. An AC adapter may be supplied with the charger, depending on the charger version. There are two types of BC-197 chargers for the ICF3210D/IC-F4210D series. 1 BC-197 Charger Type Chargeable Battery Charging time With AD-120* BP-264 Ni-MH battery Approx. 2 hrs. With AD-121* BP-265 Li-ion battery Approx. 2.5 hrs.
6 OPTIONS DD OTHER OPTIONS • AD-98FSC antenna connector converter Allows you to connect an external antenna with a BNC connector. • HM-158L/HM-159L speaker-microphone Combination speaker-microphone that provides convenient operation while the transceiver is on your belt. • HM-171GP speaker-microphone GPS speaker-microphone for the digital mode operation.
OPTIONS 6 ■■VOX function 1 The transceiver has a VOX function, which allows hands-free operation. An optional headset (HS-94/HS-95/HS-97) and a plug adapter cable (OPC-2004) are additionally required. • The VOX (voice operated transmission) function starts transmitting when you speak into the microphone, without needing to push the PTT switch; then, automatically returns to receive when you stop speaking. DD Optional unit connection qq Rotate [VOL] to turn the transceiver power OFF.
6 OPTIONS DD Turning the VOX function ON or OFF The VOX function can be turned ON or OFF when turning the transceiver power ON. qq Rotate [VOL] to turn the trans[ROTARY SELECTOR] ceiver power OFF. [VOL] ww Set [ROTARY SELECTOR] to any channel other than Channel 16. ee While holding down [PTT] and [Upper], rotate [VOL] to turn ON the power to switch the VOX [PTT] function ON or OFF. • One beep sounds when the VOX function is turned OFF. • Two beeps sound when the VOX function is turned ON.
OPTIONS 6 DD Setting the VOX gain The VOX sensitivity level can be adjusted from 1 (minimum) to 10 (maximum). qq Connect the optional headset (HS-94, HS-95 or HS-97) and OPC-2004. (p. 36) ww Rotate [VOL] to turn the transceiver power OFF. [ROTARY SELECTOR] [VOL] ee Set [ROTARY SELECTOR] to Channel 16. [PTT] rr While holding down [PTT] and [Upper], rotate [VOL] to turn ON the power and enter the VOX [Upper] [Lower] gain adjustment mode.
7 SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize W ARN ING such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment.
SAFETY TRAINING INFORMATION 7 • DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC and IC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. • DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). “50% duty cycle” is also applicable to VOX/PTT mode.
A-7081D-1EX-w Printed in Japan © 2013–2014 Icom Inc. Printed on recycled paper with soy ink.
INFORMATION EN MATIÈRE DE SÉCURITÉ Votre radio Icom produit une énergie électromagnétique de radiofréquences (RF), en mode de transmission. Cette radio est conçue pour un «usage professionnel seulement» et classée comme tel, ce qui signifie qu’elle doit être utilisée uniquement dans le cadre d’un travail par des personnes conscientes des dangers et des mesures visant à minimiser ces dangers. Elle N’EST PAS conçue pour une «utilisation grand public», dans un environnement non contrôlé.
• NE PAS faire fonctionner la radio sans qu’une antenne appropriée y soit fixée, car ceci risque d’endommager la radio et causer une exposition supérieure aux limites établies par la FCC et d’IC. L’antenne appropriée est celle qui est fournie avec cette radio par le fabricant ou une antenne spécialement autorisée par le fabricant pour être utilisée avec cette radio. • NE PAS émettre pendant plus de 50 % du temps total d’utilisation de l’appareil («50 % du facteur d’utilisation»).
