SECTION 3 IN ELATION BE SURE TO READ THE FOLLOWING INSTRUCTIONS CAREFULLY BEFORE OPERATION 351 UNPACKING Carefully remove your transceiver: from the packing carton and examine it for signs of shining damage. Should any: be: apparent.. notify i the: delivering: carrier or dealer im= immediately, stating: the Al sorter of the damage. H s recommendation you Keep the shining cartons, [1n the event storage; nonliving. of reshipment becomes: necessary they wilt she handy.: @ Accessory: cabals; ‘plugs; etc.
3.4 ANTENNA Antennas play Al very [important role i radio: communist cation. 1§ the antenna is inferior, your transceiver cannot give vou: the best performance. With 4 good antenna and feeder cable having 50 ohms impedance; you should easily gt the devised matching and performance.: Carefully install a:high:performance sateen that rusts the frequency band(s) You wish tolerate ion and place it as high impossible.
using: @ tape ‘recorder connected to tHe: headphone jack, With: & stereo headphones set inserted this way, however, the headphones will nose: the send anion side | With the plug inserted completely; only headphone quarks: 311 COOLING FAN The rear of the PA unicorns designed Yo provide for adequate cooling, but with 200 Watts input the final stage produces Quite: a: bit of heat, and. it temperature: may rise during prolonged recommissions.
switch the memory channel i3 locked fans the 'operating frequency (displayed frequency) can be changed by turning the tuning control. 21, BAND SELECT: FUNCTION SWITCH By pushing in this switch, the operating band Js changed by rooming the TUNING CONTROL: anthem HAM BAND made; each Initialized frequency of the band s selected. In the GENERAL COVERAGE mode, the ‘operating frequency Is changed: In: IMHO greps but the tower digits do-shortchange. 22 INCREMENTAL: TUNING: CONTROL Shifts the: receive frequency 9.
4.3 BEAR PANEL CONNECTIONS RECEIVER ANTENNA. OUTPUTTED TERMINAL WTH CONTROL: TERMINAL ANTENNA, CONNECTOR: EXTERNAL ALL TERMINAL: RECEIVER INPUT TERMINAL W SPARE TERMINAL B AROUND TERMINAL G TRANSVERSE TERMINAL 55. ANTENNA (ANT} CONNECTOR This IS used 10 convict 8n antenna to the set s imp ads acne is 50 offish and connect with a PL-258 connector. 66, KEY: JACK For CW aeration, ‘connect a ey here using & sanitarian 174 inch plug: : For electronic Keying the terminal voltage must Hie less thin 0.4V DC.
‘ SECTION 5 OPERATING INSTRUCTIONS 5.1 HOW TO TUNE The Following: instructions Lear for wining Ha any mode: Please read carefully. and: understand fully: before dining ON: Your unit. ! Proper: tuning necessarily for optimizing operation.
in the HAM BAND mode DOWN: 7,050.0 Pz 70800 i & 3.550.0: 10,0500 & 4 1:900.0 14.050.0 + 4 28.050.0 180500 4 § & 24.560.0: 00 21.050.0: 4 % 210800 24,8500 4 : ¥ 18.050.0 28.050.0 4 & 14:050.0 1.800.0 & & 10.060.0 38800 the GENERAL COVERAGE made; when the operating: Frequency teaches the highest ior digestions; of range: by turning the \TUNING .CONTROL cons tenuously: {at: this time: the: BAND: SELECT FUNCTION switches not \pushed N, the operating ‘Frequency goodwill to therein MMz range.
Rotating the control to the direction raises the racing frequent, and to the direction lowers one. To turn OFF the RIT function; push again the RIT switch and the: letters: “RIT and shifted frequency: displayed on the frequency display ‘are ino: longer displayed: :When the RIT circuit is OFF; the transfinite and receive frequencies are the foolhardiness of the shifted frequency: However the shifted frequency iis stored initiate: merry: and Lt will reappear when the RUT switch is pushed again.
i youngish: transfer exasperating frequency 114.206 MHz] and mode {(UBE} into a VFO, push the FREQUENCY: TRANSFER button, and the operating frequency /14,208 MHz: amid mode TUBS! ave transference anti the VFO previously selected. NOTE:: the NEO/MEMORY: switch: before pushing the FREQUENCY TRANSFER button to transfer the: operating: frequency: {at this: time, T4.
6. BY turning the set into the transmit mode. or rotating the TUNING CONTROL: o pushing: the VEQ: switch; RIT o XIT switch; MEMORY switch, or ane of the MODE SELECT snitches the scan stops and clears. When the: operating frequency s higher ‘than tha high edge (14.300MHz) and the SCAN START/STOP Hutton punished, the scan starts from the operating frequency and sun: down to the low edge. but it will retain To the memorized: high' edge frequency [14.
